Question about Vacuums

Open Question

Sony transformer E239177 drawing - Vacuums

Posted by Anonymous on


3 Suggested Answers

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017

  • 1 Answer

SOURCE: Sony transformer E239177 is the

I have the same problem... Did you find the solution? Thanks in advance.

Posted on May 01, 2011

  • 1 Answer

SOURCE: Sony transformer E239177 is the

I have a same problem too,, but now i finally solve it LOL. It 10vvvvvvvv. ^W^.

Posted on Jun 09, 2011

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

3 Answers

How do I convert a kirby ultimate G from 110V to 220V

You can't. The Kirby draws too many amps for a step down transformer.

Ask Kirby direct if they can convert your head to 220V. click Support - Contact

Kirby Ultimate Vacuum Kirby Models

Nov 10, 2016 | Kirby Vacuums

1 Answer

How do you rewire a relay

The relay contacts are wired in series with the motor, circuit breaker and switch. The relay coil is wired in series with the transformer secondary circuit, the control wires to the valves in the wall. Also the on switch is wired in parallel with the control wires.

You did not ask about the transformer but the primary windings are wired to be always on. If you need a picture I can draw you one.

Jan 31, 2014 | Electrolux Central Vacuum

1 Answer

From 220V to 110V controller ASM modification, is it possible?

some models and switch behind for convert in that way the transformer had been designed for to do it.
Other models coming according to the country example USA, most of them use 110VAC, other 220VACsuch Europe
However you can ask to the factory by asking if they have a kit for converter to 220vac to 110vac
God bless you

Jul 31, 2012 | Vacuums

1 Answer

New bell. Was working OK but, following a power outage, does not respond when pressed.

Door Bell? Did any of the electrical circuit breakers trip? Boor bells have a low voltage transformer and seems like its not getting power at the transformer.

Feb 12, 2011 | Vacuums

1 Answer

Emerson microwave MW8119 makes a noise when not on. Is this a hazard

It really depends on the particular noise it is making. The control circuitry, clock, etc. will draw some electrical current and consume power when not in use, and will be making use of a smaller step-down transformer within the unit. You may get a slight hum from this, with perfect hearing in a room where you could hear a pin drop. Anything louder than that, and there may be power applied somewhere in the unit where there shouldn't while in a standby mode. If you could get an ammeter and safely use one to measure the current draw of the unit, it may be helpful. Please exercise caution with line voltages though, they can be deadly.

Dec 24, 2010 | Vacuums

1 Answer

What is the wattage onroomba 560

The power supply isn't a transformer, its a switching power supply. The power supply is different for different locations, but you should not plug a 110V only power supply into a 220v source or vice-versa. You should contact iRobot if you wish to obtain the correct power supply for another location or to determine if they have an autosensing model that can sense and adapt to either 110v or 220v. You can also use a step down transformer to convert from 220v to 110v. The charger should be using 20W or less, but it will be pulling the current in narrow surges from the peaks of the voltage wave (aka a high 3rd harmomic current) and you will need to use a 40W or larger transformer to avoid unexpectedly overheating the transformer core.

Aug 25, 2009 | iRobot Roomba 560 Robotic Vacuum

Not finding what you are looking for?
Vacuums Logo

Related Topics:

28 people viewed this question

Ask a Question

Usually answered in minutes!

Top Vacuums Experts


Level 3 Expert

2572 Answers

Les Dickinson
Les Dickinson

Level 3 Expert

18424 Answers

D. Floyd Kolb
D. Floyd Kolb

Level 3 Expert

43501 Answers

Are you a Vacuum Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides