Question about Zebra TLP 2824 Printer

1 Answer

I have wristbands that are continuous without sensing mark. can i set where the print area beings and ends for each band in continous mode on zebra tlp 2824 printer

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 25 Answers

Go to "Printer Settings" and set the size/width/start/end. There will be numbers in MM that you can set everything up by.

Posted on Nov 26, 2013

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
Bubbabear64
  • 2794 Answers

SOURCE: Zebra TLP 2844-Z Test page print within Win XP

This printer requires special software to print labels with. It uses a unique PCL language to work with. Thats why when you use these printers with Fedex or UPS software, it typically downloads forms first before working.

Zebra used to see a label designer program to work with it. You might want to check with them to see if they still carry it.

Posted on Jul 29, 2008

IrishDruid
  • 2712 Answers

SOURCE: Zebra Printer TLP 2844-Z - Will not print from application - prints SM 10 53 4D

Hold the feed button while turning on the printer. After a config label prints, turn the printer off and then on again, and try printing again.

Also, make sure the lid is closed far enough to engage the lid sensor. If the red light comes on again, press down a bit on the lid, hit the feed button and try to print again.

Posted on Oct 23, 2008

  • 62 Answers

SOURCE: Zebra TLP 2824 Labels printing upside down.....How do we correct?

Change orientation in the printer driver.

Open printer & Faxes folder, Double click on printer driver icon,

Zdesigner driver, click on properties, click printing preferences, tick the box "rotate 180%" Click apply & ok.

If driver is Zebra TLP2824, same as above, but hit the + on "Paper output" and turn "rorate 180%" on, then click apply.

Posted on Nov 20, 2009

  • 62 Answers

SOURCE: Hi can you help ? My zebra TLP 2824 printer keeps

If you are using a ribbon remove it and perform a calibration, hold down feed key for 2 seconds as you power on, release key and wait for it to complete its calibration, when it has stopped shifting labels (wait for 10 secs to be sure) HIT THE FEED KEY to exit dump mode. If it has successfully calibrated it will feed a label each time you hit feed key. Re-install ribbon, make sure ribbon is pushed formly onto drive sprockets and then re-run the calibration..

If this does not fix problem. download firmware to latest version. This will automatically reset printer to factory default condition.

Posted on Nov 20, 2009

  • 185 Answers

SOURCE: Zebra TLP 2844 Desktop Printer

The printer driver should be set to Continuous or it will think it is still Gap or Black Mark. Please adjust accordingly

Posted on Dec 20, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

My Zebra printer is skipping three labels


if black bars on the back of tags, go to control panel, printer pref, advanced settings, tracking media should be mark sensing, then if using QBPOS, when printing select
use black bar indexing

Sep 11, 2011 | Zebra TLP 2824 Printer

1 Answer

Contunues shooting


You put the camera into one of the Continuous modes by holding the Release Mode button (to the right of the LCD control panel on the top of the camera, marked with a set of overlapping rectangles) and turning the command dial on the back. The two choices are Continuous Low and Continous High (marked with the overlapping rectangles and the letter "L" or "H"). Frame and shoot as normal.

In continous mode the camera will take pictures as long as your finger remains on the shutter release button or until the buffer fills up. In Continous High the camera will take as many as 4.5 pictures a second. Custom Setting #d6 controls how fast Continous Low shoots.

Bear in mind that the speeds mentioned are only maximums. If your shutter speed is set to half a second, you're obviously not going to take four pictures in one second.

This is all in the manual, under "Release Mode".

Jun 11, 2010 | Nikon D90 Digital Camera with 18-105mm...

1 Answer

How do I configure a Zebrazm4 Plus printer for a


Usually the easiest way to do this is to make sure the printer driver you're using is set for continous labels. This setting will vary depending on the driver / software being used to print labels. You can also go into the SETUP mode on the printer and make sure MEDIA TYPE is set to continous. Be aware that most printer drivers will override the setting in the printer. You may set to continous in the printer but if the software is set for die cut labels, then the printer will act for printing die cut labels when a format is sent to the printer.

Mar 25, 2010 | Zebra Z4Mplus Label Printer

2 Answers

We are in need of thermal printers and Zebra LP


The LP2844 can only print on Direct Thermal labels.

DT labels have the ink within the label and the labels react to heat. If these labels are to be exposed to direct sunlight they will eventually turn black.

Hint:
If you scrape the label with fingernail you can usually see the black ink on label

The physical size of the labels is this max width 1 inch (MInimum) to 4 inches (Max). Maximum length of label depends on the amount of memory in printer but maximum size for standard LP2844 is 11 inches. With full memory can be 22 inches long.

The labels must be on a 1 inch core.

These printer can handle all label types.

1: die cut Labels - Use gap sensing.*
2: Labels with Black mark on back - Use Black mark*
3: Continuous roll - select continuous *

* Select in printer driver media setting

Use the latest ZDesigner Driver V1.5.10
Download from Zebra Website.

Printer Preferences - Advanced Setup - Media Type.

Dec 02, 2009 | Zebra Eltron TLP 2844 Thermal Label...

1 Answer

My printer won't caliberate using a 1.25 inch circular label. The label stock is white, the backing is an opaque whiteish with black lines between each...HELPPPPP


Zebra printers use 2 methods to sense the gap between labels. Transmissive or Reflective. Your labels have a black mark on the backing. Your printer uses these black marks to detect the gap between your labels. Ensure that your printer's mode is set to REFLECTIVE & check that your printer driver media also is set to BLACK MARK. Print a config label to look at your printer settings.

Nov 06, 2009 | Zebra 110Xi III Plus Thermal Printer

1 Answer

Cant print on butterfly label with Zebra TLP 2844 printer


This is a problem of label sensing.

You are probably using the Gap sensor on the 2844, unfortunately the shape of the butterfly labels means you are sensing the wide gap between the labels in the centre, so it will not print anything in the apparent gap area on both ends of the label.

What your label or system supplier should have done is supplied you with the same labels but with a 3mm wide black mark on the underside of the label backing paper, centred between the labels. You can then change the printer sensor setting in the driver to Black Mark. You will then be able to print anywhere between the black marks.
Any problems with this contact us directly at Lancer labels Ltd

Nov 28, 2008 | Zebra TLP 2844-Z Thermal Label Printer

3 Answers

Zebra TLP 2844 Desktop Printer


make sure you have selected the correct media in the printer driver. The tracking mode has 3 options, (1) Web Sensing (Cut Labels), (2) Mark Sensing (Black marks on back of liner) and (3) Continuous . In your case select continuous. It sounds like the printer is in the wrong media mode and is feeding labels looking for a mark or gap and when it doesn't find one it flags a media error.

Aug 15, 2008 | Zebra TLP 2844-Z Thermal Label Printer

1 Answer

Zebra 4m


If you are in rewind mode and don't rewind the printer will pause while the rewind spool tries to catch up.

Jan 10, 2008 | Zebra Z4Mplus Label Printer

1 Answer

Printing die cut labels on Zebra Z4Mplus?


Set the printer to transmissivefrom reflective gap sensing.

This will cause the printer to loog for the inter-label gap to tell it where the top of the label is at.

Steve Weinrich
LazerTek, LLC

Dec 15, 2007 | Zebra Z4Mplus Label Printer

Not finding what you are looking for?
Zebra TLP 2824 Printer Logo

Related Topics:

42 people viewed this question

Ask a Question

Usually answered in minutes!

Top Zebra Office Equipment & Supplies Experts

pkwc

Level 2 Expert

254 Answers

Dave Busselle

Level 1 Expert

54 Answers

CheckitRight
CheckitRight

Level 3 Expert

1362 Answers

Are you a Zebra Office Equipment and Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...