Question about Maytag 24 in. MDB5600A Jetclean II Built-in Dishwasher

2 Answers

Maytag Quiet Series 300 only goes to RINSE ONLY

No matter what buttons we push, it automatically goes back to 'rinse only'. We will push 'normal wash' and all the correct buttons will light up. The machine turns on, starts going, then moves straight to 'rinse only' and the goes dark after a bit. No soap flap opening, everything is just rinsed. It's like RINSE ONLY is the ONLY thing it can do!

Posted by on

Ad

2 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Master:

    An expert who has achieved Level 3.

  • Master
  • 492 Answers

Try unplugging the washer to reboot the computer board. Sometime power surges at night can cause undervoltage on the board and make it do funny things. Rebooting by removing power for 10 min will drain the board and start with a fresh program. This is true for microwaves, dishwashers, dryers, etc.....

Posted on May 08, 2009

Ad
  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

I found that unplugging eventually works. however, this seems to be a chronic condition related to the dishwasher itself not power surges because it happens again and again. i guess i'll just keep resetting it but quite annoying.

Posted on Feb 20, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Dishwasher control light blinking


1 Press down the overfill protection float on the floor of the dishwasher's tub in the right, front corner near the door. If it cannot move up and down freely, the "clean" light will flash.
2 Make sure the dishwasher's water supply is turned on.
3 Look for suds on the inside of the dishwasher and wipe them off with a wet cloth. If the washer's sensor detects suds or foam, it may not run. Use the correct amount of dishwasher soap, not hand soap or detergent for washing dishes in the sink, to ensure suds and foam do not form. Also, make sure the cap on the rinse aid dispenser is secure--this will keep suds and foam from forming as well.
4 Close the dishwasher door. Push the "normal wash" button, then push the "heated dry" button. Push the "normal wash" button again, and push the "heated dry" button again.
5 Watch for all of the lights on your Kenmore dishwasher's panel to turn on and then turn off. The washer may start a new wash cycle at this point; if you do not want it to do so, press the "cancel" button. Otherwise, allow the dishwasher to run through this cycle.

Nov 25, 2010 | KitchenAid 24 in. KUDI01FLSS Stainless...

1 Answer

I used the "rinse only" cycle on the dishwasher a little while ago. I've never used this cycle before. After dinner I tried to start the dishwasher, but no other buttons on the panel respond except the...


Try un-plugging the dishwasher (check for cord under the sink) or turn off the breaker to it to re-set the control board. If this does not resolve your issue you may have a defective key panel.

Jun 18, 2010 | Dishwashers

1 Answer

Kenmore Ultrawash dishwasher Model 665 15810000. Originally "water heating" light was flashing and no water in dishwasher. Replaced water inlet valve. Turned power back on, normal wash light goes on...


lock light is locking the panel push this child lock button for 3 sec and see if it un locks . then try it again .. may have a pannel out. mm

Dec 06, 2009 | Washing Machines

1 Answer

Lock light stays on


It sounds like the circuit bontrol board is cracked or shorted, which means it must be replaced.

Jul 24, 2009 | Kenmore 15762 Dishwasher

1 Answer

Blinking quick rinse and lock on lights


Try holding down the "lock" button.It may be the way to unlock the problem.

May 26, 2008 | Kenmore 16602 / 16604 / 16609 Built-in...

2 Answers

Kenmore Dishwasher #15769


Try this solution first
Push the Hi-temp and then push the Sani-rinse. Go back and forth multiple times on these two buttons. I found that after a handfull of pushes that a "1" came up on the display. I continued to keep rotating the two buttons and then a "2" came up on the display and the dishwater started it's "drain" phase. I then hit cancel to clear and then I selected the cycle I wanted. The washer started up just as normal at this point.

Feb 16, 2008 | Kenmore 15769 Built-in Dishwasher

1 Answer

Flashing quick rinse light on panel


I had the same problem but I found someone wh said that there is a way to reset the dishwasher. I tried it and it has worked so far.

Here is what I did.
Push the Hi-temp and then push the Sani-rinse. Go back and forth multiple times on these two buttons. I found that after a handfull of pushes that a "1" came up on the display. I continued to keep rotating the two buttons and then a "2" came up on the display and the dishwater started it's "drain" phase. I then hit cancel to clear and then I selected the cycle I wanted. The washer started up just as normal at this point.
Good luck!

Oct 24, 2007 | Kenmore 15769 Built-in Dishwasher

2 Answers

Kenmore Ultra Wash Dishwasher - Blinking Quick Rinse Light


I had the same flashing light problem first the normal wash flashing light then the others. I tried shuting of the breakers but nothing. I tried resetting the panel by pushing normal wash and heated dry simultaneously and nothing. So I took the six screws holding the front panel out and unplugged the ribbon type wires and plug and unplugged it several times to help make a better contact and I was able to get it to work right away. This may not work for all but I worked for me. It is very easy to do and it's worth a try if you're having the same problem. It took me less then 10 minutes.

Oct 16, 2007 | Dishwashers

Not finding what you are looking for?
Maytag 24 in. MDB5600A Jetclean II Built-in Dishwasher Logo

1,976 people viewed this question

Ask a Question

Usually answered in minutes!

Top Maytag Dishwashers Experts

Mike

Level 3 Expert

4339 Answers

yadayada
yadayada

Level 3 Expert

76070 Answers

Brad Brown

Level 3 Expert

15628 Answers

Are you a Maytag Dishwasher Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...