Question about Uniden DCT7585-4 Phone

1 Answer

Handset beeps when turned on

Beeps 4-5 times then goes into a dial tone and works normally. it is trying to tell me something. I have no messages-all are deleted and it still happens... Why?

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    New Friend:

    An expert that has 1 follower.

    Greenhorn:

    A rookie expert who has answered 20 questions on their first day.

  • Expert
  • 125 Answers

Just a test tone

Posted on Nov 27, 2013

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Technician can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Technician (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 1 Answer

SOURCE: Uniden DCT648-3 "welcome Please Wait"

You need to replace the battery

Posted on Dec 25, 2007

CORDLESSGURU
  • 106 Answers

SOURCE: handset does not work

Your handset is no longer communicating with your base. Depending on your model, the solutions can be a couple of different options. If I could view pdf files on this computer I would look it up for you. But here is the link to the manual on Unidens website- http://www.uniden.com/pdf/TRU8865-2om.pdf

Nonetheless, give this a try. Power down your base, and pull the battery out of your handset. Plug the battery back in the handset and set the bad handset in the base cradle, and then power up the base. Wait about 30 seconds, then give the phone a try. If it still does not work, then you need to try to "re-register" the bad handset back to the base. Look in the manual under "registration" procedures. Hope my help fixes it for you. Good Luck, CG

Posted on Feb 18, 2008

  • 1 Answer

SOURCE: The VM indicator displays on my handset but there are no messages

I saw that someone else posted this solution and it worked for me. Unplug the power on the base unit and then reconnect the power while holding the "find hs" button. I just did this and it fixed my blinking light problem.

Posted on Mar 26, 2009

  • 1 Answer

SOURCE: When I get ready to dial, phone beeps 3 times

You must have an answering service from your phone company, and probably don't know about it. Try dialing your own # and wait for the prompts.

Posted on Aug 10, 2009

popsgifts
  • 160 Answers

SOURCE: Has new battery, but no dial-tone,

Replacing the battery reset the phone to the factory defaults, which means you'll have to restore the connection to the base in Menu-Setup

***Don't forget to VOTE for the guys who take an interest in helping!

Posted on Apr 19, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have 2 problems. 1. The orange message light will not stop flashing no matter what I do. 2. Some how the system was switched from touch tone to dial tone. I can't seem to that switched either.


Resetting the voice message waiting indicator
When you receive a new voice mail message, the new message LED on the top of the handset flashes. In the event your message waiting light gets out of sync with your phone company's
voice messaging system, you can manually reset it back to the "No messages waiting" state.
1. Press and hold FiND on the base for five seconds.
Note: The handsets connected to the base will start to beep, however, keep pressing for five seconds.
2. A beep sounds and the message alert tone is reset.
Changing the dial mode
Your phone can communicate with the telephone network in two different ways: tone dialing or pulse dialing. These days, most base networks use a method called tone dialing, so your phone comes programmed for tone dialing. If your phone company uses pulse dialing, you will need to change your phone's dial mode. If you don't get a dial tone or can't connect to the telephone network, please follow the steps below to modify your phone's settings:
1. Press MENU/SELECT.
2. Select the Global Setup menu, and then the Dial Mode submenu.
3. Scroll to highlight Pulse.
4. Press MENU/SELECT. You will hear a confirmation tone.
If you ever need to change the dial mode back to tone dialing, follow the same procedure, but select Tone in step 3.

Finally for future ease of use, here is a link to the user manual were I copied the above information from:

http://www.uniden.com/content/ebiz/uniden/resources/ownersmanuals/DECT1580-3om.pdf

Jul 21, 2011 | Uniden DECT 6.0 Cordless Phone ID

1 Answer

MESSAGE LIGHT CONTINUES TO BLINK ON ALL HAND SETS (THERE ARE NO PENDING MSGS) WHEN I TRY TO DIAL OUT, (INSTEAD OD A STEADY DIAL TONE) I GET A RAPID BEEPING DIAL TONE) AFTER 7 TIMES, THEN IT BECOMES...


You have unheard messages on the voicemail system provided by your telephone company. This system records messages when someone calls while you're already on the phone. Please contact your telephone company for instructions on accessing their voicemail system.

Jul 09, 2011 | Uniden DECT 6.0 Cordless Telephone...

1 Answer

Modem tells me there is no dial tone


Connect the modem to a telephone-jack.
Make sure that the telephone-wire has *FOUR* strands, not just *TWO* strands.

Or, unplug the FAX, and plug a telephone into that telephone-jack, and listen for a dial-tone.

Do you have electronic voice-mail from your telephone company?
If so, does it "beep" a few times when you pickup the handset?
Such "beeps" can confuse any modem that expects *instantly*
to "hear" a dial-tone.

Nov 01, 2009 | Zoom ADSL USB Modem

1 Answer

NO DIAL TONE!!


Hi! I can't say for sure this is your problem, but if you lose power for a time, the handset that is not in the answerer base will quit working. You then have to take that handset and put it in the base cradle (where the working phone sits) and leave it there for at least 20 seconds. After the base recognizes it again, it should work. If this doesn't cure the problem, then probably the phone is damaged. Hope this works for you! Hal

Jun 06, 2009 | Uniden Cordless Phone

1 Answer

Dialtone, but no dialing


Uniden offered a replacement, stating that the base phone was probable beyond repair.

Jun 04, 2009 | Uniden DECT 6.0 Cordless Telephone...

1 Answer

No dial tone in Clarity C4230 setup


if you can get dial tone with another phone, look into manual for any instructions, usually a toll free number for help. ( BEST ) otherwise take phone back for exchange. may be problem in the board.

Apr 16, 2009 | Clarity C4230 Cordless Phone

1 Answer

When preparing making a call, I get a series of short dial tones.


Have you tried erasing all of your recorded messages? Usually the short dial tone beeps mean you have a pending message.

Jan 05, 2009 | Big Button GE 29369GE1 Speakerphone

1 Answer

Handset has No link to base


I was having the same problem with the same model phone, and fixed the problem by rebooting the phone – unplugging the AC and phone cord from the base station and plugging both back it, then removing and replacing the handset to regenerate the security code.

Nov 17, 2007 | Xact Communication XG2200 Cordless Phone

2 Answers

Handset No Link To Base error and no dial tone


I have the problem. I think it is because the battery i have in it was a Ni-MH and it should be a Ni-Cd. I am now looking for the right baterry Good luck Frank wolfgang24@verizon.net

Jan 27, 2007 | GE 900 MHz Phone

1 Answer

Handset ?No Link To Base? error and no dial tone


2/29 Have you registered or re-registered the handset?
"No link" can mean handset is not accepting radio wave of base unit. At Mfgr website pull-down operator's manual and look for registration instructions. Some sequence of buttons will create a radio signal from base (have handset off base) then another sequence of buttons on handset will accept radio signal. If handset has "menu" button, try "menu", then "00" (zero zero) then select an accept or "OK" button. Good luck.

Jan 14, 2007 | Xact Communication XG2200 Cordless Phone

Not finding what you are looking for?
Uniden DCT7585-4 Phone Logo

79 people viewed this question

Ask a Question

Usually answered in minutes!

Top Uniden Lands Phones Experts

kakima

Level 3 Expert

102366 Answers

Cindy Wells

Level 3 Expert

5223 Answers

Les Dickinson
Les Dickinson

Level 3 Expert

18411 Answers

Are you an Uniden Lands Phone Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...