Question about Hobart D300 Stand Mixer

1 Answer

My D300T motor is turning but shaft is not. How do I open the shaft area.

When I turn on the D300T its motor is running but its vertical shaft is not turning. Before it stopped turning it was running heavy, it was making weird sound and eventually stopped turning while it was kneading the dough. I have taken apart the top cover, 4 screws on the small cap, 4 bolts and the spring clip but I can't still not remove the bolted plate cover.

Posted by on

  • Amir Orellana
    Amir Orellana Aug 17, 2017

    I have one and the 1st gear do not wrk what can i

×

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Novelist:

    An expert who has written 50 answers of more than 400 characters.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

  • Expert
  • 126 Answers

Weird sound usually means something in the gear box. I found a copy of the manual which includes many exploded drawings; perhaps something in here might help:
http://www.bakedeco.com/ebay/pdf/HobartD300.pdf

Posted on Nov 23, 2013

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

bigg t
  • 640 Answers

SOURCE: hobart p660

There are 2 set screws.Make sure their both out,if for some reason there is only 1 set screw these are your options.Heat the shaft and remaining pin with a mapp torch (you can buy them at home depot,lowes for $40 bucks),heat it up really good then get a punch and try to knock out the pin,option 2---if you cant get the pin out then youll have to replace the shaft and if thats the case you should also clean out the planetary and replace the bearings and seals.If the hole in the shaft is oblongated or worn you should probably replace the shaft because the dough hook will rock the pin back and forth breaking the pin.Also look inside the hook and make sure thatI its not worn out where the pin sets.IF you see thee hook or shaft pinhole worn you will break the pin again if you are able to replace the pin.I work for hobart and service mixers regulary,if you need part numbers or advise let me know.

Posted on Nov 28, 2007

  • 1 Answer

SOURCE: motor is not running now

Yes, bigg t, since you work for Hobart, is there any way to get a refurbished one cheaper? If so, email me sosdogs@comcast.net. THANKS!

Posted on Jan 20, 2008

bigg t
  • 640 Answers

SOURCE: Dough Hook Stops moveing under heavy load

Does the mixer work in any other speeds?Are you mixing pizza dough and in what speed?I service these mixers alot--i work for hobart.It sounds to me like you have a sheared key on one of the shafts.The mixer doesnt have a clutch.

Posted on Feb 22, 2008

  • 68 Answers

SOURCE: Hobart A-200 Motor Direction

No, do not swap hot and N.

First, verify rotation. As the attachment shaft rotates, it should push the engagement pin into the keeper slot. Looking down on top of the mixer, the planetary should rotate clockwise.

If the unit runs backwards, does it start slow? Can you get it to run either way by giving it a push start before turning on the power? If so, your start switch is not working properly. (Which is my guess) Check your capacitor.

There is mechanical and electronic start switches. (Metal arms and a contact or a little gold rectangular metal can.)

Check it out and let me know what you find -- Mike

Posted on May 19, 2008

ricardok45
  • 135 Answers

SOURCE: bread dough

Hi. There are several possibilities. First, you should always proof your yeast. Take a 1/3 cup of WARM water, add a half tsp.of sugar and yeast, wait 10 minutes. If your yeast becomes frothy its active and can be used. If not, get some fresh yeast. Second, use a flour that has a high protein content (10-12%) if you're not using pans to make your bread. High protein develops more gluten than low protein flour. Gluten development will give your dough body, and prevent your dough from flattening. Third, after mixing. knead the dough by hand for 8-10 min., cover and let rise until doubled, punch dough down and divide. Knead the portions by hand for 8-10 mins. Shape loaves and place on baking sheet or use pans,let it rise untill doubled,then bake as usual. Been there...Done that. Let me know how you make out. Ricardok45.

Posted on Dec 31, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Hobart 20QT guessing old a200 motor runs fine removed top cover to see but gears not working and mixer does not spin Any diagnosis Help greatly appreciated


The first vertical shaft has a brass gear that runs off the rotor. The ancient models had a spring loaded slip clutch built onto the gear. Upgrade it with a worm shaft kit which gives you a complete new shaft and fixed gears. I think it includes the upper and lower bearings. Maybe replace the grease if it has not been done. Or look for a sheared key on the worm shaft.

Feb 19, 2014 | Food Mixers

1 Answer

Braun Vario 280 Watt type 480 hand held blender. The bowl top that the hand mixer fitsd into is frozen. The hand held motor works but the shaft in the top that turns the blade is frozen. I don't...


HI.This steps might be as well helpful.let me just clarify that you can't even manually twist the shafting.If the motor is working an yet it will not turn the shaft.Tha shafting bossing might as well been broken misallign inside..Better remove the cover by unscrewing it and then try to observe how the motor works.If it really does turn when ever it is plugg on to the source.Observe also misallign bosssing that connects the shafting and the motor's rotor.Thank you for choosing FIXYA.

Aug 16, 2011 | Braun M880 MultiMix Hand Mixer

1 Answer

Motor runs, output shaft doesn't.


When you hear the motor running and you can visually see the shaft does not, a gear is stripped. Which gear? You have to open/bring to a repair center to find out.

Nov 15, 2010 | KitchenAid KP2671 Professional 6 Series...

1 Answer

Blade will not turn


motor will hum but no blade turn if bottom seal worn and material leaks into shaft. Rekove drive head and try turning shaft if nio go dissasemble entire unit ,clean and service, replace seals

Sep 20, 2009 | Robot Coupe MP600 750 Watts Hand Mixer

2 Answers

I suspect my D300T Hobart Mixer has a broken shaft I Need a parts/manual listing to help me take apart mixer, retreive broken parts and then order required parts


Hi. Go to hobartservice.com, register for free. This will allow you access to the parts files for your D300T mixer. Download them. When you begin your disassembly, take a photo of every piece that you remove, lay these pieces on a piece of cardboard or something suitable in the order that they were removed. This will help you greatly with your project. Good luck! ricardok45

May 12, 2009 | Hobart D300 Stand Mixer

1 Answer

Motor runs but Beater shaft does not turn


Hi guys. Kitchenaid does not publish a parts catalog for your KSM90's. Your best bet would be to take it to a small appliance repair place and get a quote to repair it. They may have an old catalog for parts. Try to find a place that has experience with KSM90's. Kitchenaid has left you twisting in the wind, like many,many others. Without these parts drawings, self repair is iffy at best. "For the way it's made"! Indeed. Sorry! I wish I could help more.

If this solution has assisted you, please rate it. ricardok45

Mar 29, 2009 | KitchenAid KSM90 Ultra Power Series Stand...

2 Answers

Hobart D300T mixer oil change.


Call your local hobart branch and tell them you need grease for a d300 mixer.Yes this mixer uses grease now.If it's older they used oil but is no longer available.

Mar 15, 2009 | Hobart D300 Stand Mixer

3 Answers

Blade won't release from mixer


Try to push up while you turn the blade. Don't be afraiid to turn hard.

Dec 30, 2008 | KitchenAid K5SS Heavy Duty Commercial...

4 Answers

Bamix slowdown - repair service anywhere out there?


click on the "contact" link in this website http://www.bamix-usa.com/ there's places in Canada & the US to have them serviced. Through contacting them they'll give you the nearest service area.
Good luck, love my Bamix!

Aug 11, 2008 | Bamix De Luxe Hand Mixer

2 Answers

Hobart A-200 Motor Direction


No, do not swap hot and N.

First, verify rotation. As the attachment shaft rotates, it should push the engagement pin into the keeper slot. Looking down on top of the mixer, the planetary should rotate clockwise.

If the unit runs backwards, does it start slow? Can you get it to run either way by giving it a push start before turning on the power? If so, your start switch is not working properly. (Which is my guess) Check your capacitor.

There is mechanical and electronic start switches. (Metal arms and a contact or a little gold rectangular metal can.)

Check it out and let me know what you find -- Mike

May 19, 2008 | Hobart A200 Stand Mixer

Not finding what you are looking for?
Hobart D300 Stand Mixer Logo

Related Topics:

248 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hobart Food Mixers Experts

Ross Keen

Level 3 Expert

1231 Answers

John Tripp
John Tripp

Level 3 Expert

4654 Answers

Pieter Vleeshouwers
Pieter Vleeshouwers

Level 3 Expert

1793 Answers

Are you a Hobart Food Mixer Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...