Question about Sunbeam Coffee Makers & Espresso Machines

Open Question

How to disassemble sunbeam EM0440

Problem with burrs? very hard to assemble, coffee grind is unusably coarse, now can't unassemble to check burr line up

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
z34aga
  • 137 Answers

SOURCE: can't disasseble burr set

take an oil filter remoover for cars(the model with 3 legs and gears will do better job). 2 man required one holding grinder other one start turning left and right the upper holder(during turning hold down the brake pin.) it is bit boring and job wich requires patience. but i think you will manage it

here is the diagram:
http://www.partsguru.com/images/Img844.jpg


Posted on Apr 04, 2009

Ad
dougpopo
  • 1 Answer

SOURCE: cuisinart burr grind and brew coffee maker

The hopper between the burr grinder and where coffee chutes into the filter is jammed with coffee powder...

First, take out the filter holder and carafe, and place a freash empty filter on the pot base to catch stuff.

Next, take out the beans holder and look for the release lever in the lower left section. Sliding it to the left slides open the door, where you'll probably find loads of powder. You can poke your finger through to get the majority, then use the cleaning brush to get it really clean.

Thanks what fixed mine! (I notice I have to do this about once every few months.)

Posted on Aug 03, 2009

  • 1 Answer

SOURCE: cuisinart burr coffee grinder

The best solution I have was referred to me by a mate of mine who services commercial coffee machines.

Step 1. Remove the base of the grinder... this is actually the hardest aspect of this task... as there is one tamper-proofing screw... if you can't get the correct star-hex screw driver I recommend drilling the screw out.
Step 2. Once the base is off you will see the main shaft of the grinders motor. The shaft has a star washer set in behind hew nut, the end of the shaft has a slot cut into for a flat bladed screwdriver. Hold the nut with a pair of pliers & you can adjust the shaft positioning (& hence the burr attached to the motor) by about 3mm....

You will need to experiment to find the correct level of fineness as you require.

If you need further information send me an e-mail as I'd be happy to forward more detailed instructions.

Good Luck.

Cheers.......

Dave (dave@kingkiwi.f9.co.uk)

Posted on Nov 04, 2009

  • 547 Answers

SOURCE: My cuisinart burr coffee grinder will not turn on

This model sometime gets plugged up with grounds.

Unplug the grinder, and remove the bin where the grounds go. Look inside the grinder part where the grounds come from the grinder into the bin. This should be clear, and you should be able to see part of the grinder wheel inside. If this is plugged up with grounds, then you'll want to clean it out, but it's possible that the motor has already burned out (we killed two of them last year at my office this way)

Pour out any whole beans that are in the top part. You can pour them in a bowl to save them, you don't have to throw them away.

Unscrew the top part until it detaches from the grinder. This will take 20 or more rotations -- just keep turning it counter-clockwise.

You'll want to do this next part over a sink or a counter that's easy to clean -- you're going to dump a lot of ground coffee.

Looking into the grinder from the top, you'll see the grinding wheel in the center, and packed coffee grounds around the edges. Use a plastic knife or bamboo skewer to clean out the ground coffee. Don't use a screwdriver, metal silverware, or anything metal, as this can damage the grinder housing. You also want to clean from the bin opening. When you're done cleaning, the grinder wheel should turn freely.

Reattach the top portion, put the bin back in place, and turn the grinder on. It should turn on and spin the grinder wheel. If it still doesn't, then your motor is burned out. :(

If it does turn, then put the coffee beans back in and enjoy a cup -o- joe!

Posted on Jan 30, 2010

  • 1 Answer

SOURCE: My Barista Burr Coffee Grinder suddenly grinds too fine.

If it is any consolation, mine just did the same thing, now takes too long to grind and it is way to fine dispite a thorough cleaning by disassembly.

Posted on Sep 26, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I took everything apart to give it a good cleaning and now all settings produce a very fine grind. Any thoughts?


I had the same problem with too fine a grind when I took mine completely apart to clean (including the lower burr). The solution I finally came around to was to further tighten the star-shaped screw which holds the lower burr assembly in place. I had originally just tightened it until the lower burr until the lower burr assembly started to turn with the screw, but that wasn't enough. So I held the assembly in place and tightened the screw further and I'm back to my previous grind coarseness/fineness.

Jan 13, 2014 | Jura Capresso 560 Electric Burr Grinder

1 Answer

Grinding makes a lot of scratch noise and coffee wouldn't drip. The machine says to fill the beans but container is full.


Likely a foreign object is blocking up the grinder. Remove all beans and run at coarsest grind to try to clear it, chase it through with more beans if necessary. If this does not clear it then the top burr of the grinder assembly can be removed after disassembling the machine. Mark the grinder coarseness cogs before moving them to assist reassembly. Moderately difficult procedure.

Aug 27, 2011 | DeLonghi Magnifica 3300 Espresso Machine

1 Answer

It says to "lift the


BURRS are the metal parts that grinds the coffee. There are 2 BURRS in the grinders, The upper burr is normally the one you adjust (Fine or coarse) and the lower or closer to the motor is the one turning during the grinding process.

Jan 25, 2011 | Starbucks Barista Burr Grinder

1 Answer

Rocky has a tumbling (unbalanced) sensation when grinding you can feel and hear. Seems less if you back off grind # to 20 from 8. Been using 8 for a year with no problem before today.


  1. take the bell(bean container) carefully out.
  2. disassemble the upper holder of burr
  3. you will see now the burrs, clean good coffee remains than disassemble the burrs
  4. after disassembling burrs clean good the lower and upper burr holder.
  5. carefully switch on the grinder tan switch off(few seconds) during lower plate is rolling touch with marker the surface of burr holder very softly,

  • if it is ok you will have complete circle
  • if it is deformed you will have incomplete circle( that you must compensate with letter tape )under the burrs you apply the letter tape
  • after each correction you mark the burr with marker to see did you achieved perfect result. once you have lower burr in place you screw bolts in upper bur holder and assemble it back in his place.

Aug 20, 2010 | Rancilio (RAROCKYND) Grinder

1 Answer

My mazzer coffee grinder brings out medium to almost a whole bean grinds ,,,am trying to get a fine grind(for the espresso) but it's not working ,,, i've tried to move the scale to all the numbers but the...


Lets do this, remove the bean hopper, and make sure there are no beans in the burr chamber. Then looking down at the collar with the numbers back up screw if there is one on it. Now if memory serves me right clockwise is coarse and counter is fine. Look down in the burr chamber, notice the nut in the middle, turn it with your fingers that will move the bottom burr, if burr turns freely we will move on if not plug in grinder and let it grind out remaining beans. With beans gone unplug grinder, then turn collar towards fine until you cannot go no more, now try turning nut it will be hard if not impossible to move, turn collar towards coarse until you can barely move bottom burr with fingers, you will hear and feel the burrs touching, that will be our bottom setting. Now pick a spot on the grinder you can use the small notch in the middle, count out 16 notches towards coarse and turn collar to that point. Use the notches around the collar not the ones on the top next to the numbers. Your grind should be almost perfect, depending on blend and machine you might have to adjust 1 notch to the left or right after testing.

Aug 11, 2010 | Mazzer Coffee-grinder SUPER JOLLY Electric

1 Answer

Cleaned the Solis Maestro grinder and re set it to a fine espresso setting but the grind is coming out very course. What should i do?


Hi Your burr is not locked in. You need to remove the beans from the hopper. Remove the hopper. Remove the burr. Turn the grinder upside down over the trash can. Put the burr back in only make sure that the burr is down. Install the bean hopper and when you turn the bean hopper it should move the burr. Then you can adjust your grind. Make sure that the grinder is running is your going to a finer grind or you could break the grinder. You can turn it to a coarse grind any time.

Jan 12, 2010 | Solis Maestro G385 Electric Burr Grinder

1 Answer

I disassembled the grinding blades and put it back together but now I can not get a find grind


HI
When you reassemble the removable burr assembly, you first must make sure that there are no grinds left in the main body's threads. These grinds will prevent the burrs from going any farther down. The burrs must touch and then back off to zero the grinder. Don't ever leave them touching though.

Nov 07, 2009 | Rancilio Rocky SD Grinder without Doser -...

1 Answer

Krups GVX2-12 Electric Burr... Problem:


First, unlock and unscrew the upper burr carrier. Clean and check the upper burr by gently running your finger over the teeth in the cutting direction. It shoild feel moderately sharp. If it feels very blunt, look at the teeth under a good light. If you see a substantial "flat spot" at the top of the teeth, probably the burr set will need replacement.
For the bottom burr, clean carefully its teeth, and the entire area in which it is housed. Include the outlet orofice as well. You may find a lot of oily deposits within here, so just clean them off as best as possible.
When all is clean, insert the top burr holder back in place. Screw it down until both burrs touch, then back it off (say) 1/4 turn, and lock.
Put some beans in the top, and switch on. Adjust the top burr until the desired grind is obtained.
The ground coffee should feel like a coarse sand when close to the desired grind size.

Mar 13, 2008 | Krups GVX2-12 Electric Burr Grinder

1 Answer

MDF very coarse grind


Several possibilities loom:

1. Same burrs for 25 years? don't be cheap replace them!

2. Dirt in the threads of the burr carrier, or the threads that recieve it?

Let us know what works

Dec 18, 2007 | Gaggia MDF Electric Burr Grinder

2 Answers

Grind


Love your 'handle'!

I'm thinking that there is something in the burr in the unit. Empty the unit and remove the burr. Usually, this is done with a counterclockwise turn. Note how hard it may be to turn...you'll have to reverse this when you put it together. Now, clean out any coffee debris you find. Then, turn the unit over and tap it on a firm surface covered with newspaper. Reassemble and return to service.

Nov 03, 2007 | Grindmaster 810 Electric Burr Grinder

Not finding what you are looking for?
Coffee Makers & Espresso Machines Logo

Related Topics:

121 people viewed this question

Ask a Question

Usually answered in minutes!

Top Sunbeam Coffee Makers & Espresso Machines Experts

ray gallant

Level 3 Expert

45441 Answers

Gil Shultz

Level 3 Expert

3368 Answers

kakima

Level 3 Expert

102366 Answers

Are you a Sunbeam Coffee Maker and Espresso Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...