Question about Baby Lock Ellure

1 Answer

Change the speed controller mode to off - Baby Lock Ellure

Posted by on


1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that gotĀ 5 achievements.


    An expert whose answer gotĀ voted for 20 times.

    New Friend:

    An expert that has 1 follower.

  • Expert
  • 186 Answers

Touch the icon at the bottom of the screen that looks like a sheet of paper. The screen that pops up should have a slider icon in the upper right. You can set it to stitch width or speed control.

Posted on Nov 23, 2013


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

My Janome 1600P does not change speeds by moving the speed control

If you are using a programmed stitch it may be set at a specific speed to accommodate the intricacies of the stitch

Oct 10, 2017 | Janome Sewing Machines

1 Answer

My Bernina 730E is varying in speed even though I am pressing foot pedal to thr floor. The speed does not stay steady, somestimes running extremely slow in full speed mode. What is wrong?

it could be pedal control or the speed control unit on the motor as it is reasonably common for that machine
take it in for a service to ensure that other factors ( thread around bobbin shaft, fluff etc is not slowing the machine

Nov 01, 2016 | Bernina Sewing Machines

2 Answers

Runs backward

I have not heard of that problem before. Small alternating current brush-type motors usually seem incapable of running in any direction other than the one they are designed to run. I am not sure if changing the relationship between the field coils and the armature will change the situation - mostly the design of the internal wiring would defeat efforts to change this.

If the speed control is electronic instead of the usual rheostat then it is possible the alternating current is being changed into a direct current by the speed control and in this case reversing the supply wires from the speed control to the motor should have the desired effect.

May 30, 2016 | Sewing Machines

1 Answer

I was given a brother cs-8150. The manual says it will operate without foot feed. I tried to use auto sew and machine tells me to change speed controller mode to off. Where do I do that.

Not able to find any online instructions for your machine, so here goes. There may be some confusion as to what foot feed means.

I believe foot feed refers to the feed dogs. When you disable the feed dogs (drop them), then you must manipulate the fabric manually--used mostly for darning or free motion quilting. In essence the feed dogs are no longer moving the fabric for you. Instead, you manually move the fabric and control the speed at which it stitches with your foot control. Perhaps that is why you need to turn off the speed control because you will determine the speed with your foot.

Foot control refers to the foot pedal that you use to control the speed that the machine sews (much like the gas pedal in your car). Some machines have the ability to sew without the use of a foot control unit. To do so, there is usually a button or lever somewhere to start and stop the machine. When activated, the machine will continue to stitch until you stop it.

Hopefully this will help you find a resolution.


Mar 28, 2016 | Brother Sewing Machines

1 Answer

How di i turn off speed controller mode

In the Setup pages. Power on your machine. Press the Settings tab. Arrow (>) through to Width Control ON:OFF. Select ON

Nov 23, 2013 | Baby Lock Ellure

1 Answer

Bernina 1000 can i add speed control?

Yes you can replace the foot control if it is no longer regulating the motor speed of your machine.

Jul 15, 2012 | Bernina 1008

1 Answer

Foot controller stays in slow speed mode -- won't go any faster -- but did previously

it probaly is worn out or bad contact, as described it needs to be replacedor cleaned

Jul 17, 2009 | Sewing Machines

Not finding what you are looking for?
Sewing Machines Logo

Related Topics:

240 people viewed this question

Ask a Question

Usually answered in minutes!

Top Baby Lock Sewing Machines Experts

Tally Girl
Tally Girl

Level 3 Expert

1129 Answers

Chris Wetmore

Level 2 Expert

185 Answers

Jon Piercy

Level 2 Expert

67 Answers

Are you a Baby Lock Sewing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides