Question about Frigidaire 30 in. Electric Gallery Series Self-Cleaning Double Wall Oven

1 Answer

F10 code and shuts off after 15 minutes of using wall oven

Oven shuts off after only 15 minutes and displays error code f10. I already replaced the sensor probe.

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Cheetah:

    An expert who has answered 20 or more questions within one hour.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 107 Answers

What is f10 code

Posted on Nov 22, 2013

4 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 338 Answers

SOURCE: Error F3 on display ovens beeps

the temperature probr is located inside your oven in one of the upper corners. it should be a round stick looking piece. some are removed from the front others are removed from the back.

Posted on Nov 26, 2008

  • 1 Answer

SOURCE: Oven locked so I can't shut door/operate oven

Thanks a million, solved the problem like a charm. For those that can't find it, it is on the left side orf the OVEN, not the stove. Once you open the door, you'll find it on the frame's upper left side corner, can't miss it. Good luck

Posted on May 05, 2009

localwonder
  • 6784 Answers

SOURCE: Frigidaire oven F-10 error

HI. this is a oven temp sensor failure notice. you will need to check the wires leading from the temp sensor to the control. if the wires are in good condition and , the sensor harness is not welded, replace the temp sensor asap.

Posted on Jun 01, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My Frigidaire oven shut off due to an f10 error which should I replace first since I have no tools to measure.ohms... sensor or EOC?


Good Morning mark, thank you for your post!

Based off the information you have provided your Frigidaire range is displaying an error code of "F10". An "F10" error code normally stands for a runaway temperature (overheating). This could be an issue with your RTD (Resistance Temperature Detector) or the EOC (Electronic Oven Control). I would recommend performing a reset on your oven and you can do that by flipping the household circuit breaker off for ten minutes. If you continue to experience an issue with the "F10" error code I would recommend having a professional technician out to your home for proper diagnosis and replacement of any electrical components. This will help you avoid any unnecessary part purchases. Hopefully this information has been helpful. -Matt

Feb 14, 2015 | Frigidaire Ovens

1 Answer

Whirlpool Oven GW395LEGT6 Replaced the oven temp sensor But oven will pre-Heat and run for 15 minutes then shut off with Error code EO F3


Have you tried pulling the connectors off the control board and reinserting them. If you still have problems the control board could be the issue.

Sep 24, 2014 | Ovens

1 Answer

F10 code after frigidaire wall oven on for 15 minutes


Good Morning Dave, thank you for allowing me to assist you!

If you are getting error code F10, it typically means that your range is experiencing an issue with the runaway temperature (overheating). One of the best ways to determine if this is a false error code is to reset the power to your range by either unplugging it or flipping the household circuit breaker off for about ten minutes. If the error code persists, I would be advisable to reach out to a professional to proceed further. Most likely the RTD (Resistance Temperature Detector) or the EOC (electronic oven control) will need replacing. Hope this helps!

Nov 21, 2013 | Frigidaire 30 in. Electric Gallery Series...

1 Answer

Receiving a F 10 message


F10 error code means "runaway temperature condition"

If your oven is overheating, unplug the power cord for a few minutes. When plugged back in if the oven is still overheating, you will need to have the temp sensor and control checked.

The first component to check would normally be the oven temperature sensor probe.
If you have a volt/ohm meter, you can shut off the breaker for the range and remove the screws that mount this sensor to the back wall of the oven. Carefully pull the wire harness into the oven cavity until you get to the wire harness disconnect plug.

You should have enough slack to pull it this far into the oven. Disconnect the sensor but do not let the wire harness retract back through the back wall of the oven or it will be hard to reconnect.
Measure the resistance of the oven temperature sensor with your volt/ohm meter. At room temperature, the resistance should measure around 1100 ohms. The resistance chart is shown in the image below.

If the resistance is above 2200 ohms at room temperature, then the sensor probe is causing the F10 error code and will need to be replaced.

You can order a new sensor probe from the Sears PartsDirect website.


Hope this helps.

Apr 25, 2011 | Kenmore 47833 Electric Single Oven

1 Answer

My Kenmore electric stove, model number 790.96122407 displays error code F10 after preheating for 10-15 minutes.


The F10 indicates that the electronic oven control board senses a runaway temperature condition in the oven through the oven sensor circuit.
This can be caused by a faulty oven temperature sensor probe or a failed electronic control board.
Oven temperature is detected by the control board as it monitors the resistance through the oven temperature sensor circuit.
You could have a failed oven temperature sensor, a wiring harness failure, an open thermal switch or a failed electronic oven control board that would cause this problem.
The first component to check would normally be the oven temperature sensor probe.
If you have a volt/ohm meter, you can shut off the breaker for the range and remove the screws that mount this sensor to the back wall of the oven.
Carefully pull the wire harness into the oven cavity until you get to the wire harness disconnect plug.
You should have enough slack to pull it this far into the oven.
Disconnect the sensor but do not let the wire harness retract back through the back wall of the oven or it will be hard to reconnect.
Measure the resistance of the oven temperature sensor with your volt/ohm meter. At room temperature, the resistance should measure around 1100 ohms.
The resistance chart is shown in the image below.

If the resistance is above 2200 ohms at room temperature, then the sensor probe is causing the F10 error code and will need to be replaced.

You can order a new sensor probe from the Sears PartsDirect website. The part number for the sensor is 316217002.

If the resistance is normal, then one of the other causes mentioned above is producing your F10 code.
You would need to access the electronic oven control board (Timer) in the console and check the resistance at the sensor circuit connection to the control board as the next step in troubleshooting this problem.


http://media.fotki.com/1_p,wbqdsfkrfqtswfqxgtqsskgwtqkq,vi/krdbrtqkgxkrbbqbrwb/1/1303472/5961857/image37801img-or.jpg


Thanks for using FixYa - a 4 THUMBS rating is appreciated for answering your FREE question.
%$#@

Dec 02, 2009 | Kenmore 40494 / 40495 / 40499 Electric...

1 Answer

F10 Error code on double oven.


Sir,
Check out this link

suggest to reset it by shutting off both main breakers to the stove , wait for one minute and switch breakers on again.

Thanks Good Luck
Appreciate to rate as "Fixya"

May 15, 2009 | Frigidaire 30 in. Electric Gallery Series...

1 Answer

F2 and F3 error codes in GE electric wall oven


Call GE answer center 1-800-626-2000 ask for tech help, Have you Model # off you data plate ready.

May 09, 2009 | GE JRP15 Electric Single Oven

1 Answer

F2 and F3 error messages on Tappan wall oven model 12-4980 10/03


These are the F2/F3 error codes for a Tappan oven
F2 Oven too hot Check Bake function, if OK, replace oven temperature sensor F3 Oven temperature sensor open Check oven temperature sensor, should be ~1100 ohms at room temperature. If too high or low, replace oven temperature sensor
please take the time to give this solution a fix ya rating.

clarkco

Feb 09, 2009 | Tappan Ovens

3 Answers

Kenmore oven error code f10


The F10 indicates that the electronic oven control board senses a runaway temperature condition in the oven through the oven sensor circuit.
This can be caused by a faulty oven temperature sensor probe or a failed electronic control board.
Oven temperature is detected by the control board as it monitors the resistance through the oven temperature sensor circuit.
You could have a failed oven temperature sensor, a wiring harness failure, an open thermal switch or a failed electronic oven control board that would cause this problem.
The first component to check would normally be the oven temperature sensor probe.
If you have a volt/ohm meter, you can shut off the breaker for the range and remove the screws that mount this sensor to the back wall of the oven.
Carefully pull the wire harness into the oven cavity until you get to the wire harness disconnect plug.
You should have enough slack to pull it this far into the oven.
Disconnect the sensor but do not let the wire harness retract back through the back wall of the oven or it will be hard to reconnect.
Measure the resistance of the oven temperature sensor with your volt/ohm meter. At room temperature, the resistance should measure around 1100 ohms.
The resistance chart is shown in the image below.

If the resistance is above 2200 ohms at room temperature, then the sensor probe is causing the F10 error code and will need to be replaced.

You can order a new sensor probe from the Sears PartsDirect website. The part number for the sensor is 316217002.

If the resistance is normal, then one of the other causes mentioned above is producing your F10 code.
You would need to access the electronic oven control board (Timer) in the console and check the resistance at the sensor circuit connection to the control board as the next step in troubleshooting this problem.


http://media.fotki.com/1_p,wbqdsfkrfqtswfqxgtqsskgwtqkq,vi/krdbrtqkgxkrbbqbrwb/1/1303472/5961857/image37801img-or.jpg


Thanks for using FixYa - a 4 THUMBS rating is appreciated for answering your FREE question.

Aug 08, 2008 | Kenmore 40494 / 40495 / 40499 Electric...

Not finding what you are looking for?
Frigidaire 30 in. Electric Gallery Series Self-Cleaning Double Wall Oven Logo

269 people viewed this question

Ask a Question

Usually answered in minutes!

Top Frigidaire Ovens Experts

Dan Webster
Dan Webster

Level 3 Expert

8220 Answers

 Fix Your Board
Fix Your Board

Level 3 Expert

310 Answers

ashburton

Level 3 Expert

417 Answers

Are you a Frigidaire Oven Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...