Question about Televison & Video

1 Answer

Sansui model stv2107 filament is not lit how can i see if the filament are dead or not.everthing is fine in the powersuply the is110v on hot but nothig else.

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 9 Answers

Your power suply is dead, check capacitor 100uF/400V on the primair side en BUT12F or other sipmos transistor. replace and it will work

Posted on Nov 21, 2013

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Black screen but still here shows


only about two possible reasons bad solder connections or the picture tube is not getting the 6.3 volts for the filaments in the neck of the picture tube.

If set is opened carefully and turned on look to see if 3 faint filaments are lit or not. If not that is your problem.

Dec 22, 2012 | Sansui 27 inch TV

1 Answer

No video only sound on CRT TV


possible no filament lit in the neck of the picture tube (there are 3 and not real bright as source is only 6.3 volts.

Possible no High voltage but most that have sound have high voltage.

You are going to have to remove rear cover to LOOK--be careful and let me know what you find, if no filaments are lit it will be a easy fix and should be easy to find---if no filaments let me know.

Dec 17, 2012 | Televison & Video

1 Answer

I have a sanyo remote and a sansui tv how do i program the tv


Hello

I don't have a code for Sansui TV to be programmed with Sanyo remote control But hava a philips Universal remote model which can be programmed for Sanyo TV and has its codes.

Remote Model ===> Philips CL 034 Universal Remote Controller.
Codes
0115 0632

And herealong with I sends some universal remote codes, that you can check it for.

Four Digit Universal remote code for Sansui TV are

0135 0310

Three digit universal remote code for Sansui TV are

135/ 136

Direct Code Entry
  1. Press and hold the SETUP button until the red indicator stays on, then release the SETUP button.
  2. Press and release the desired Mode button (TV, VCR, etc.). The red indicator blinks, then stays lit.
  3. Enter the 4 digit code from the code tables. Note: after a valid code entry, the red indicator turns off. For an invalid code, the red indicator flashes.
  4. With your device on, press CHANNEL UP. If the device responds, no further programming is required. Note: If some buttons do not operate your device, try one of the other codes for your brand.




Nov 25, 2010 | Sansui Televison & Video

1 Answer

Sansui 1908 sound but no picture, kid was using


Return the thing. Ur LCD inverter board is dead.Or call for warrenty repair.The LCD inverter have no set of times,it dies anytime.Must replaced the LCD inverter board to get picture back.

Nov 06, 2009 | Sansui 19 in. LCD TV

1 Answer

I purchased a new battery for my 1997 hyundi sonta but everything is dead. when time to come home from work hopped in my car everthing was dead jump lead no problems went straight away drove home about 17...


Sounds like the ground wire for the battery is not making clean contact. Trace that wire and clean both ends and the area it connects to the engine block. Good luck!

Aug 06, 2009 | 1997 Hyundai Sonata

1 Answer

Is there a study that not turning your tv off (older model)Sony trinitron will make it last longer ???? my email is onomia7@yahoo.com please help me find the answer


that is nonsense.the heater filament in the picture tube is on anyway,in some tv many years ago the filament went off.all instant on tubes have the filament lit.

Jul 17, 2009 | Sony FWD-50PX3 50 in. Plasma TV

1 Answer

Amana le8107w2 air circulation is fine but air temp is not hot


Heater filament is either dodgy or burnt out ... if you would like to repair it yourself check Espares.com for your model and make.

Apr 22, 2009 | Dryers

1 Answer

Sansui 2110


as your sound is ok so your power supply & high voltage section is ok.(eht). please check 1 filament is glowing, 2 crt base for loose 3 voltages on crt points 4 luminance in chroma ic

Sep 14, 2007 | Sony FD Trinitron WEGA KV-36FS120 36" TV

Not finding what you are looking for?
Televison & Video Logo

Related Topics:

20 people viewed this question

Ask a Question

Usually answered in minutes!

Top Televison & Video Experts

The Knight
The Knight

Level 3 Expert

73619 Answers

Cindy Wells

Level 3 Expert

5056 Answers

Electro Med Services...
Electro Med Services...

Level 3 Expert

6694 Answers

Are you a Televison and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...