Question about Goodman GMS90703BXA Heater

1 Answer

Goodman gmt070 inductor fan clicks on, pilot glows, nothing

Inductor fan clicks on, pilot glows, nothing happens. Then it repeats the above cycle & ignites.

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Master:

    An expert who has achieved Level 3.

  • Master
  • 497 Answers

Possible bad igniter...igniter should read somewhere from 50-90 ohms. If not it is going bad. Remove igniter (don't touch carbon silicon rods) see if you see minute cracks or white spots. If ohms testing reads in 90 or above range , replace igniter. ( note some rheem, rudd and weather king igniters normal ohm range can be 130-150 ohms).. You might also want to check the igniters connections and control board module to make sure the the igniter is betting the proper voltage to get the igniter hot enough.. 110 volts or about is the input norm to the igniter.

Posted on Jan 03, 2014

3 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

SOURCE: Inductor blower comes on and runs then the ignitor

I cleaned the sensor that was at the the right further most burner on my Goodman and it worked. got the answer to my problem here at fixya. My burner flame only lasted 5 secs before it shut off. Thanks to all who took the time to send me a response.

Posted on Oct 05, 2011

  • 36 Answers

SOURCE: Goodman GMH80905CN inductor running blower is not

Release the vacuum line and blow into it when it first starts. If this works then it is a bad pressure switch. If not then locate the safety sensors around the burner. Jump them out until the gas valve opens and lights the burner.

Posted on Mar 01, 2013

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Goodman GMH80905CN inductor running blower is not


Release the vacuum line and blow into it when it first starts. If this works then it is a bad pressure switch. If not then locate the safety sensors around the burner. Jump them out until the gas valve opens and lights the burner.

Feb 28, 2013 | Goodman Heating & Cooling

1 Answer

99 gtp console shift inductor not in sync with dash shift inductor


common problem on gm products
the shifter has a cable going to trans. sometimes it stretches and the prndl gets out of sync.
you could also look at the cable going to the dash from steering column. it is about 3" and gets tangled up.

Jan 26, 2013 | 1999 Pontiac Grand Prix

3 Answers

Inductor blower comes on and runs then the ignitor glows flame comes up and burns for approx. 10-15 sec then goes out then fan comes on. Model number is PBKMLB12N0B0F I believe this is a goodman furnace.


I cleaned the sensor that was at the the right further most burner on my Goodman and it worked. got the answer to my problem here at fixya. My burner flame only lasted 5 secs before it shut off. Thanks to all who took the time to send me a response.

Nov 13, 2010 | Goodman Heating & Cooling

2 Answers

Have a Goodman GMT070-3B which the vent motor seems to be sticking. I took apart and cleaned the brushes and reassembled. The furnace will come on only after what seems like the vent motor comes up to...


The whole assembly must be replaced.

The sequence of operation is -

Combustion fan purges the heat exchanger. A pressure switch verifies combustion air fan is running. Usually a 30-45 second purge before the hot surface ignitor glows, or the spark ignition starts.

Gas valve opens after 10-15 seconds and main burners light. Control board monitors for flame and shuts gas valve after 2-3 seconds if main burner does not light.

If burner does not light, some boards repeat this for 3 tries, then locks out and is reset by cycling power.

Air blower comes on after another 30-45 seconds after main burner ignition.

Times may vary based on the specific controller board. A flow chart and timing sequence should be located somewhere on the unit, usually in the fan compartment.

Dec 16, 2009 | Goodman GMS90703BXA Heater

1 Answer

Goodman GMT070-3A heater. When heater is turned


look for flashing code thru blower door peep hole aftter it shuts down and let me know the amount of flashes

Dec 03, 2009 | Heating & Cooling

3 Answers

Inductor L2 Broken of NDS Lite


0 Ohms. You can just bridge it with solder.

Jun 26, 2009 | Nintendo DS Lite Console

1 Answer

GOODMAN CMA80905CXBA FURNACE. INDUCTION BLOWER NOT ENERGIZING. GETTING 3 "BLINKS" FROM DIAGNOSTIC LIGHT (LOW PRESSURE SWITCH OPEN). THE A/C WORKS & THE BLOWER FAN COMES ON WHEN THE STAT IS IN...


the pressure switch is closed before the draft motor closes it.the board is telling you that this is not right.pull the wire(either) off of the pressure switch to see if furnace tries to light.if it does,you should replace the pressure switch.

Oct 02, 2008 | Goodman Heating & Cooling

1 Answer

Ds Lite not power up L2 Inductor is not good not work.


For the L2 L4 inductor specification, I check the following website, on there have original L2,l4 inductor power and specification

http://www.logictoyz.com/nintendo-ds/nintendo-ds-lite-spare-parts/ds-lite-l2-inductor-power-replacement-.html

By the way,L2,L4 is not fuse,
It is Inductor power

May 30, 2008 | Nintendo DS Lite Console

1 Answer

Fan turns on and off rapidly


The fan cycling problem on the T23 series usually indicates a loose solder or missing inductor which is usually on the underside beneath the PCMCIA slot. If you replaced the mobo yourself you may have flexed what is a weak solder joint loose - you will need to pull the board and resolder this or have someone else do this for you. You can sometimes get the laptop to start by flexing the assembled laptop gently around the PCMCIA slot and if so then that almost always means an inductor problem. You can find some photos by googling (images) "T23 mobo" or "T23 motherboard".

Feb 19, 2008 | IBM ThinkPad T23 2647 Notebook

Not finding what you are looking for?
Goodman GMS90703BXA Heater Logo

110 people viewed this question

Ask a Question

Usually answered in minutes!

Top Goodman Heating & Cooling Experts

Dan Webster
Dan Webster

Level 3 Expert

8220 Answers

paulcarew

Level 3 Expert

2460 Answers

Brandon Berry
Brandon Berry

Level 2 Expert

407 Answers

Are you a Goodman Heating and Cooling Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...