Question about Dryers

Open Question

Whirlpool dryer awz 7466

No warm air

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get to try the service completely Free afterwhich it costs $6 per call and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 55 Answers

SOURCE: Whirlpool AWZ 3303 Tumble Dryer

http://www.whirlpool.co.uk/ifudocs/501930700361GB.pdf

Posted on Mar 25, 2008

Ad
  • 1 Answer

SOURCE: Whirlpool AWZ 650 condenser dryer

MY FILTER LIGHT IS ONN ALL THE TIME, HOW DO I CLEAN THE FILTER...WHERE IS IT, IS IT THE ONE BELOW THE FRONT DOOR THAT PULLS UP AS IN THAT CASE I'VE CLEANED THAT?

Posted on Aug 27, 2009

rogrrabbit
  • 986 Answers

SOURCE: Whirlpool AWZ 7303 tumbling but not drying.

blower wheels will get loose in dryers. Sometimes they will get a whole lump of lint in them or you can hear a rattling noise in the dryer, this is the blower wheel, its worn out and it can cause the fuse to blow too,or it can half *** work and take fifty forever's to dry the clothes.Or it could be just that the dryer needs a good blowing out .I use a lawn blower to get all the lint out of the dryer as well as the vent pipe and vent to outside. I take the filter HOUSING out and wash it also. That is, I remove the housing and clean is good! Making sure that the dryer is properly flowing air is a good thing!

Posted on Sep 12, 2009

  • 77 Answers

SOURCE: Whirlpool AWZ-7813 won't dry - no heat

it will either be you element or the thermostats that have failed.

Posted on Mar 20, 2010

  • 1 Answer

SOURCE: have to replace broken belt on a whirlpool awz

Double the belt and slide it between the two arms of the tension pulley. Then slip the belt over the drive motor pulley. The belt will be pushing against the tension pulley from underneath.

Posted on Sep 30, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Awz 8676


Try this link http://tumble-dryers.tech-specs.com/whirlpool-awz-8676-n30037723

Aug 29, 2014 | Whirlpool Dryers

1 Answer

Whirlpool awz 8666 all programs working but no hot air


Is this a washer or dryer? If it's a dryer, is it gas or electric? If it's electric then reset the breaker (both) in the box. Need more information

Jan 06, 2014 | Whirlpool Washing Machines

1 Answer

Whirlpool AWZ 410 washer dryer is not generating any hot air when drying. The dryer drum is tumbling but with cool air only.


Unplug the unit and take the top with the screws holding the lid on. Take a look at all of the wires on the top of the machine. You might notice broken/burnt wires on the safeties that are close to or that directly activate the heating element located in the blower housing located at the top of this washer/dryer condensing unit.

Nov 26, 2013 | Whirlpool LER4634J Electric Dryer

1 Answer

Whirpool awz 7466 is not drying


check regulator, gas and thermal fuse

Nov 03, 2013 | Whirlpool Dryers

1 Answer

It's a whirlpool awz 7466. It runs fine, but I do not know which settings it needs to be on to dry my clothes normally. A small load will take at least 2 hours and makes laundry take forever. Any help


Hi Jennifer,

Two hours to dry a small load of laundry (even a large load for that matter) is way too long. You're wasting electricity too. The first thing you should do is consult the manual for the dryer to be sure you've selected the proper setting. The literature for this can be found here.

Consult this literature page 63 for the location and cleaning instructions for the (e) lint filter after each drying cycle and (h) heat exchanger at least monthly. Failure to clean both will result in long drying times. If you have the "Gentle" cycle selected, drying time will be prolonged, too.

Hopefully, these suggestions will help you solve the problem. Good luck!

Jan 07, 2013 | Dryers

1 Answer

I have a whirlpool dryer model AWZ 3513 and the filter light is on but the filter is spotless and I have cleaned out the extract tube


If the ambient air temperature is below 10 Degrees C the drier will not work and I think the filter light is a warning for the temperature as well.

Nov 29, 2010 | Whirlpool AWZ7303 Electric Dryer

1 Answer

Whirlpool AWZ-7813 won't dry - no heat


it will either be you element or the thermostats that have failed.

Mar 20, 2010 | Whirlpool Dryers

2 Answers

HOW DO I LOCATE THE HEATING ELEMENT ON THE 6TH SENSE DRYER


take the back panel off it is located in the rear.

Mar 19, 2010 | Whirlpool Dryers

2 Answers

How to clean a whirlpool awz7913 condenser tumble dryer heat exchanger


how do i clean my heat exchanger on the whirlpool awz 7913 condenser tumble dryer?

Jan 19, 2010 | Whirlpool Dryers

2 Answers

Whirlpool tumble dryer model NO- AWZ 121/3-belt replacement


how do i replace my belt on my tumble dryer

Jan 09, 2010 | Whirlpool Dryers

Not finding what you are looking for?
Dryers Logo

Related Topics:

15 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dryers Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17130 Answers

Brad Brown

Level 3 Expert

15941 Answers

Are you a Dryer Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...