Question about RCA HD52W140 52" Rear Projection Television

1 Answer

HD52W140YX! Set will power on. No display @ all. Know where to get a schematic? Chassis ATC311. If I get a chassis schematic will that help solve a problem within the TV?

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.


    An expert who has answered 1,000 questions.

  • Master
  • 1,153 Answers
Re: HD52W140YX!

Check first R14705 to see if burnt! If so then HV Trans is bad. Also if you need schematic try

Posted on Oct 08, 2007

Add Your Answer

0 characters

Uploading: 0%


Complete. Click "Add" to insert your video. Add


3 Points

Related Questions:

1 Answer

How do I know if it is L6 or L3 chassis

you need to look on the right side of the set (facing the front of the set) for a small label that says
model code...
serial number..
if the version number is blank or PW01 you have the
L3 chassis.
if it says PU02 then you have the L620 chassis
also the L3 chassis has the ballast on a slight angle and the L620 has the ballast straight.

Dec 29, 2008 | Projection Televisions


HD52W140 White screen with retrace lines then shuts down

This has the ATC311 chassis. I have found that capacitor C14703 has actually been loose on the deflection board and that had caused the set to have a white screen with retrace lines then the set would shutdown. I resolderd this and normal operation was resumed.

on Feb 23, 2008 | RCA HD52W140 52" Rear Projection...

2 Answers

RCA R52WH74 (ITC222A Chassis)

no the board that has the FL231 on is the ITC222 deflection board. The other board is above the chassis in a seperate frame that runs across the set the convergence power supply is the board on the left above the board where the fL231 is. Yes the ITC222 and ITC222A are the same chassis. As for the service manual that site should have the service manual under the thomson category as the ITC 222 chassis is actually a thomson chassis made for RCA.

Sep 11, 2008 | RCA R52WH73 Projection Television

1 Answer


I will need you to look on the rear tag and let me know the chassis number as that model was produced with two different chassis numbers ITC222 and the ATC221 chassis was used, But the chassis number will be on the tag on the rear panel. Please reply to this same post and I will help you locate the power supply board.

Aug 13, 2008 | RCA R52WM24 52" HDTV Projection Television

1 Answer

Binks 5 times

You need to replace the capacitors on the power board. this is a very common problem with the RCA dlps See my tip under my profile for the ATC336 chassis RCA, your model is the ATC311 but it applies to your model as well.

Aug 05, 2008 | RCA HDLP50W151 50" Rear Projection HDTV

2 Answers

RCA HD50LPW42 problem

Your chassis is the ATC311 the capacitor issue is with the ATC336 chassis. How many times does the led blink?

Jun 26, 2008 | RCA HD50LPW42 50" Rear Projection HDTV

1 Answer

Mitsubishi ws-65511 No power green light blinking

yes the capacitors on the DM need replacing. depending on the chassis some have 4 capacitors on the DM board where as other chassis have 7 capacitors on the DM power supply that are causeing the problem. If you dont know which chassis your has go to this link and leave them an email they can help you figure it out,

May 31, 2008 | Mitsubishi WS-65511 65" Rear Projection...

1 Answer

Power supply

Almost, but i would recomend getting the training manual for your set so you dont buy a power supply needlessly as the training manual has step by step proceedures for your Chassis to diagnose whats wrong. You need the ATC311 training manual. They will email it to you at the following link.

May 06, 2008 | RCA HD61LPW42 61" Rear Projection HDTV

1 Answer

How do I access the power supply? I'm Stuck!

Remove electric chassis. Power PCB is under back end cover of chassis unit.

Sep 29, 2007 | Mitsubishi WD-52525 52" Rear Projection...

1 Answer

RCA P52940 Television

The P52940 uses the CTC195 series main chassis. The most common reason for the set not to start up is a shorted flyback (high voltage) transformer. The set actually does try to start, but the computer immediately detects the extra current drawn by the shorted flyback and instantly shuts the set back off. The chassis should be checked and the flyback replaced by a qualified tech familiar with RCA projection TV's.

Aug 12, 2007 | RCA P52940 52" Rear Projection Television

Not finding what you are looking for?
RCA HD52W140 52" Rear Projection Television Logo

Related Topics:

190 people viewed this question

Ask a Question

Usually answered in minutes!

Top RCA Projection Televisions Experts

The Wyzzyrd

Level 2 Expert

83 Answers

D. E. Hev

Level 3 Expert

1059 Answers

Ron Dufek
Ron Dufek

Level 2 Expert

397 Answers

Are you a RCA Projection Television Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides