Question about RCA D770 Remote Control

2 Answers

Rca universal remote

I have a rca universal remote that quit working, I changed batteries, but lost the book with the codes. The red light works when I hit any key, but I need to reprogram it, can you send me the instructions and codes on line?

Posted by on

2 Answers

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer
Re: rca universal remote - RCA D770 Remote Control Remote Controls

Website not working

Posted on Aug 14, 2008

Add Your Answer

0 characters

Uploading: 0%


Complete. Click "Add" to insert your video. Add


3 Points

Related Questions:

1 Answer

My rca universal remote stopped working and it lights up so the batteries are working, i tried reprogramming didnt work..what do to?

You may just need to buy new one Dollar store has RCA 4 in 1 Remote with code book for $6.00
Mats has them for $3.95 and up orginal handunits too.1-800-628-1118

Mar 24, 2010 | RCA 3-Device Universal Remote with...

1 Answer

Need to program my tv with an RCA universal remote and I lost the book

i lost my book too but got told you can press set button and the on that has tv on it hold them down till the red light stays on then press after the power button on remote and hold down till tele turns of they all have auto scan on them incase there aint a code takes a bit longer but works for me. hope this helps

Dec 03, 2008 | RCA RCR450 Remote Control

2 Answers

Program the RCA#rcr312 universal remote control

hold the code search buttton until light comes on then select the device you are programing and enter code

Oct 22, 2008 | RCA Universal Remote Control

9 Answers


I can help. I too have an RCR312W remote and it did not work.
I found this code on message board. The code from the RCR311W remote works.

1) turn on unit

2) press and hold componet button on remote (TV, VCR, etc)
until On/Off lights up

3) press and hold On/Off while holding component button. Light will go out. Continue hoding both buttons until light comes back on.

4) release both buttons. On/Off should stay on.

5) Press On/Off repeatedly until unit turns off.

6) Press the Stop key at bottom.

7) light goes off. Remote is programmed!

Oct 17, 2008 | RCA Universal Remote Control

5 Answers

Converter box codes for rca universal remote rcr3273/3373 for zenith or lg boxes

if It is similar to most RCA universal remotes, to get the code follow these steps(Manual code search MAy take awhile):
1:Manualy turn on the component that u want to control
2: press and hold the component key (ie SAT while holding SAT press ON-OFF key(button) for three seconds until all of the components light up and release the keys(button).
3: keep pressing ON-OFF key until your component turns off.(Note may take awhile)
4: one the correct code is found hit the STOP key and it will save your component IF YOU DO NOT HIT THE STOP KEY THE CORRECT CODE WILL NOT BE STORED.
Hope this works

Oct 07, 2008 | RCA 3-Device Universal Remote

1 Answer

Rca universal remote

If none of the codes work then we have two other solutions:

1. Searching For Your Code

If you have tried all of the set-up codes for your brand of equipment ,or yourbrand is not listed, and you are still not able to get the unit to respond, trythe following procedure to search for your code.
If you don't find a code that works, the remote will flash four times when youreach the end of all the codes for this device type.
  1. PRESS the button for the device you want to program, (TV, VCR, CABLE, etc.), then RELEASE.
  2. PRESS and HOLD the SETUP button until the red LED flashes twice, then RELEASE.
  3. ENTER 9-9-1 (two blinks on the remote)
  4. ALTERNATE slowly between the POWER key and the DEVICE (TV, VCR, CABLE, etc.) button until your device turns off. (On VCR, LD, and CD players use PLAY instead of POWER)
    Make sure that the remote is pointed at your device during the search, You may have to press this sequences of buttons up to 100 times to search the entire library of codes.
  5. When your device turns OFF, PRESS the SETUP button and RELEASE it to lock in the code for your device.

2. Learn the buttons from the original

Line up your original remote and the head-to-head before completing thefollowing steps.
  1. PRESS and HOLD the SETUP button until the red LED flashes twice.
  2. PRESS 9 - 7 - 5, the red LED will flash twice.
  3. PRESS the DEVICE key where you wish to learn the function. The next 3 steps must be completed within 10 seconds.
  4. PRESS the button that will receive the learned function, the LED will flash rapidly.
  5. PRESS the button on the original remote to be learned.

Now you can repeat steps 3 through 5 to learn other functions onto other keysor press and hold SETUP until the Cinema's red light flashes twice to lock inyour new feature. (If the red light does not blink twice, stop and repeat stepsthrough 6).
To test the new feature, press and release the device key in which the newfeature was learned followed by the key on which the feature was learned

More help for programming your remote can be found here:

Hope that helps! Should you have any further questions,please feel free to post them here.
Television Video - DVD Audio Satellite Set Top Box Video - VCR Brand: Model (optional): clip_image001.gifclip_image001.gifWe could not find an exact match, we think this code will work. 10054 clip_image001.gifclip_image001.gifSetup Instructions
· Set the "Mode Switch" to TV.
· Press and hold the "Mute" button and the "Select" button until the visible LED blinks twice.
· Enter the 5 digit Code above.
· Try your new code and tell us how it worked!
You'll have to settle for that, use the middle power key in the tv device to power on & off the tv.

hope this may help;



Aug 14, 2008 | RCA Universal Remote Control

1 Answer

Remote Control wont Work

I cant seem to program my RCA universal remote to my emerson tv

May 28, 2008 | RCA Universal Remote Control

4 Answers

RCA universal remote code

i lost my book with my codes . can you tell me the correct code to my rca to my zenith television

Apr 10, 2008 | RCA RC-U703SP Remote Control

2 Answers

Rca remote

The model number will be in the back, on the lid of the battery cover.

Nov 12, 2007 | Remote Controls

Not finding what you are looking for?
RCA D770 Remote Control Logo

Related Topics:

230 people viewed this question

Ask a Question

Usually answered in minutes!

Top RCA Remote Controls Experts

The Knight
The Knight

Level 3 Expert

66685 Answers

andy williard
andy williard

Level 2 Expert

226 Answers

Cindy Wells

Level 3 Expert

4723 Answers

Are you a RCA Remote Control Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides