Question about Sport & Outdoor - Others

Open Question

Installing firing pin for cooey 840

Istalling firing pin for a cooey 840 20 guage

Posted by Anonymous on

2 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

kingbenny325
  • 11 Answers

SOURCE: i need to replace a firing pin in remington 1100

I know of a few sites that you should be able to order the part from: http://www.gun-parts.com/remingtonshotgun/, and the Remmington website parts page: http://www.remington.com/support/parts/model_1100.asp, and if you prefer they may have on gunbroker.com

Posted on Nov 29, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have 1985 GMC 4/4 it keeps popping fuseable link on fire wall I have checked all the wiring. The red wire that into the fire wall the fuse block show to have direct short when the ignition switch is


I'm not sure which one you are talking about, if I remember correctly there are 2 on the firewall. One is a 16 guage wire which protects all red 12 guage wiring. The other is a 20 guage wire that protects the generator warning light and the field circuitry on the alternator. It will be protecting a 16 guage wire.

Sep 01, 2014 | 1985 GMC K1500

1 Answer

Tk 840 UHF


you also have to apply power to the pin labeled 'ignition'

Jan 10, 2014 | Kenwood Radio Communications

1 Answer

I just purchased a 1995 GMC K1500 with a 5.7L (350) that has been rebuilt. When i got the truck the temp guage was not working and it would not blow any hot air. Upon a little investigation i found there...


its a possibility. or heater matrix is blocked up ( usual suspect ) remove thermostat and/or hose. undo radiator bleed key ( if has one ) and let a hosepipe run through it for 20 mins or so and see if it clears it.

Dec 22, 2011 | GMC Sierra Cars & Trucks

1 Answer

"HELP" HE ISTALLED NEW 3.0 LONG


year? model? what are you working on?

Dec 21, 2010 | Ford Ranger Cars & Trucks

3 Answers

Hi i have a yaesu ft 840 the display go's blank and then it flashes till a turn it off how can i fix this thankyou


1: Remove regulator board (has the two 78xx IC's mounted on it).
This board is mounted to the mid-chassis, heat-sunk with a gray rubber gasket behind it. It's connected to the main board via pin&pinch pad, in the back by the audio IC.
2: Check the IC's, replace if faulty.
3: re-stress the pins and look for cold or broken solder joints.
4: Re-install and check. You should have your display back and it will probably go to 7.000MHz (default out of the box).
For fills, contact ware103@comcast.net

Oct 30, 2010 | Audio Players & Recorders

1 Answer

How do you get the fuel pump out of the gas tank on a nissan frontier 2003


remove the fue tank,then remove the queck connectors,six screw,then retainer,then fuelpump and fuel level sensor assy....istallation always replace theo ring and install new one after that turn the ignation on, do not start the engine check for leaks, install pressure guage,,,..

Jun 29, 2010 | 2003 Nissan Frontier Crew Cab

1 Answer

I need to replace a firing pin in remington 1100 20 guage and i dont know how to get to it


I know of a few sites that you should be able to order the part from: http://www.gun-parts.com/remingtonshotgun/, and the Remmington website parts page: http://www.remington.com/support/parts/model_1100.asp, and if you prefer they may have on gunbroker.com

Nov 29, 2009 | Remington Sport & Outdoor - Others

4 Answers

Spedometer guage not working


to fix this you have to remove the instrument cluster, it's not hard (4 screws) and take it apart. On the hidden part of the board, there is about 20 contact points (where the cluster connects) all you have to do is reheat the solder around those pins and add solder accordingly and you'll have an instrument cluster that's good as new

Jun 08, 2009 | 1995 Plymouth Neon

1 Answer

Oven touches cabinet inner wall of cabinet. Fire hazard or not?


The rear of the oven has approx 3" or better insulation you are ok

Jan 17, 2009 | Cadco OV-250 Electric Single Oven

Not finding what you are looking for?
Sport & Outdoor - Others Logo

Related Topics:

50 people viewed this question

Ask a Question

Usually answered in minutes!

Top Sport & Outdoor - Others Experts

yadayada
yadayada

Level 3 Expert

75051 Answers

kakima

Level 3 Expert

102366 Answers

Brad Brown

Level 3 Expert

15451 Answers

Are you a Sport and Outdoor - Other Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...