Question about OKI C5650n LED Laser Printer
Posted by Anonymous on
I have experienced a similar problem for quite some time and I am glad that I have found several solutions to the problem. I will be implementing the solutions whenever the problem reoccurs. Otherwise, that was an informative question and answer session and if you need assistance with content writing you can hire our writers by clicking on PROFESSIONAL WRITING EDITING SERVICES
Posted on Aug 23, 2017
You will need to contact the support for that its easy still check out these links <a rel='nofollow' href="https://www.officesetup-com.com/">www.office.com/setup</a>
<a rel='nofollow' href="http://www.nortonhelp.me/">www.norton.com/setup</a>
Www office com setup Office com setup
Posted on Aug 21, 2017
I've faced this problem on my C301dn, I've tried to reset it but no way (I've also broken several plastic part doing it!!!), finally I've solved as below:
- I've bought another fuser (oki original), installed and used for a couple of days, then I've re-installed the old fuser...and it works perfectly!!! Not the most economic way but at least you have a spare fuser for the future
Posted on Oct 17, 2016
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
SOURCE: 980: Fatal Error
From the Service Manual:
*Error by media
clinging to the fuser
*Media has clung to the fuser.
Replace the fuser unit.
Before you replace the fuser, take it out and check for a piece of stuck label, paper, etc. You can spin the fuser roller by turning the gear on the side.
Posted on Apr 07, 2008
SOURCE: does anyone know what is
If you look on top of the fuser roller(upper orange roller), there is a thermistor (orange rectangle plastic that rides on the roller) you will see four wires going into that housing. Two are for the thermistor and the other two is for the fuse that is built into the housing. You would have to use a soldering iron to melt the plastic that the fuse is sitting in. You would have to figure out what to use as a fast blow fuse.
Okidata makes it difficult to take out the thermistor because the nut is locktite on the screw. Try using the soldering iron to melt it. Just make sure you dont damage the thermistor.
Posted on Jul 03, 2009
The instructions below do not apply to my okidata c6100. It does not go to "NV-Ram initial" , after you get to " Engine Dialog Mode" , even if you scroll down.
I bilieve that the okidata c6100 has a different way to reset the drum units.
Anybody can help,
1. Turn machine on while pushing and holding the TWO up/down menu buttons at same time.
2. Menu window will show "OKI USER"
3. Scroll to " Engine Dialog Mode" is indicated. Push Enter button.
4. "Diagnostic Mode xx.xx.xx S-Mode is indicated.
5. Scroll to "NV-Ram initial" is indicated. Push ENTER.
6. Window shows "NV-Ram- Initial Table 1".
7. Push ONLINE and ENTER Buttons simultaneously and HOLD for 10 seconds after you see "Executing Reset" appear in menu window.
8. Restart printer.
Posted on Mar 09, 2011
Tips for a great answer:
Jun 18, 2011 | OKI C5650n LED Laser Printer
Aug 18, 2010 | Office Equipment & Supplies
Jun 18, 2010 | OKI C5500n Printer
Sep 14, 2009 | OKI C5500n Laser Printer
Jul 22, 2014 | OKI C5650n LED Laser Printer
5,133 people viewed this question
Usually answered in minutes!