Question about E-Machines eMachines Desktop PC

1 Answer

Emachine 5210 We have somehow managed to lose the config file from this machine, so it now won't work. Any ideas?

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Novelist:

    An expert who has written 50 answers of more than 400 characters.

    Champion:

    An expert who has answered 200 questions.

  • Expert
  • 231 Answers

Hi, The only way I can think off here is to re-install the O/S. Assuming its XP then run your XP disk and as setup runs choose the SECOND PROMPT TO RUN A REPAIR TO WINDOWS. If you choose the first prompt It wont do anything, if you choose to just reinstall you will loose all your data. the second prompt will appear to completely reinstall but you will save your existing files. Goodluck mistyman

Posted on Oct 08, 2007

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I put new ram in my emachine 5210 why won't it work


If it was working before you put the ram in, then the ram you put in is the problem. Maybe you put in a ram that is not compatible or is bad.

Put the old ram back in to see if it works.

Go to 4 All Memory to make sure you get the memory that is for your computer.

Go to 4 All Memory at:

http://www.4allmemory.com

Jun 08, 2012 | Computers & Internet

1 Answer

What memory do i need for a emachine 5210


You have 2 slots and each slot will take 1GB modules of PC 3200 DDR400 Ram. So with 2 of them you will have 2GB of PC 3200 DDR400 total.

May 19, 2012 | E-Machines eMachines Desktop PC

1 Answer

Setting up the emachine for the first time and keyboard won't work. checked all connections.....???


Is the keyboard a USB Keyboard or PS/2... If it is a USB keyboard try plugging it into a front USB port and see if it works. If it does you might have a lose usb cable going to the back of the computer.

Jun 30, 2011 | E-Machines eMachines Desktop PC

1 Answer

My cisco 4503 keeps losing it's configuration file.. any ideas why this is happening? thx.


Hi,

The case gives me hints towards the configuration register value which is not set to proper value, so the switch is not checking the the saved configuration in the config file.

Please do the below steps.
1. Log into the switch
2. Come to enable prompt
3. Typein the below commands
config t
config-register 0x2142
end
write memory

The find an example of the prompt and the commands below

Switch# config t
Enter configuration commands, one per line. End with CNTRL/Z.
Switch(config)#config-register 0x2142
Switch(config)#end
Switch#write memory


After this you can configure your switch as per your requirement and then save the config by typing write memory

Now you can reboot your switch and the switch will come up with the configuration as you set.

Best Regards

Nov 06, 2010 | Cisco Catalyst 4503 (WS-C4503) 12x1000...

1 Answer

My e machine 5210 needs video drivers as pitcure


Hello
No your wallet can stay shut.First you need to identify your graphics or video device.
Go to control panel,personalization,display,advanced.your graphics device or video card should be listed there.

Write down the manufacturer.Go to there websight and find your device usually at the support section.

Download and save file in my documents,once done open file and install to pc.

E machine also has a update utility at there websight youll need the model and serial # of your pc to use it.This will update all devices on yur pc.

Thanks.

Jan 21, 2010 | E-Machines eMachines Desktop PC

1 Answer

Emachine t3092, no video, can't find certain desktop files


If they're not on the drive, they're not on the drive. Your only other option is to search the free disk space for the remainder of those files. For that you can use the free trial of O&O Unerase Personal. I hope you get those files, never fun to lose memories over a peculiar computer issue.

Mar 22, 2009 | E-Machines eMachines Desktop PC

1 Answer

CDRom stops working when I connect IDE cable


put some different power connector other than you have used now, then check

Nov 20, 2008 | E-Machines eMachines Desktop PC

1 Answer

Emachine 5210 not working


how old is your emachine?? is your display in condition?? if so, your smps might've worn out.. this is what happens when the display is proper but u still don see anything on the screen..

Mar 12, 2008 | E-Machines eMachines Desktop PC

1 Answer

Emachines 5210


Can you hear fan inside the PC? Any flashing lights next to the power button? Please give us more details.

Oct 23, 2007 | E-Machines eMachines Desktop PC

Not finding what you are looking for?
E-Machines eMachines Desktop PC Logo

Related Topics:

226 people viewed this question

Ask a Question

Usually answered in minutes!

Top E-Machines Computers & Internet Experts

Alun Cox

Level 3 Expert

2678 Answers

Les Dickinson
Les Dickinson

Level 3 Expert

18425 Answers

Brad Brown

Level 3 Expert

17473 Answers

Are you an E-Machines Computer and Internet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...