Question about Smeg DWI614 Built-in Dishwasher

1 Answer

Smeg Intergrated Dishwasher

The Top shelf water outlet does not seem to be spinning. I open the door mid cycle and it is still in the same place and the dishes have food on them.Can you help me sove this please? I am allergic to washing up.

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 121 Answers

Do any objects hang down (or stick up from below) and block it? Is the shelf pushed all the way in so it gets water through it? Does it seem to be spraying water, but not spinning?

Try spinning it by hand to see if it moves freely. It may just be blockede by a small object in the water.

Posted on Nov 07, 2007

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a Smeg DI 112-1 intergrated dishwasher, when i switch on, light 5 flashes continuously and pressing the program selection button does nothing,


i have had success with dishwashers that have a (frozen) motor this involves
1 turn off electrical supply and or remove plug from receptacle.
2 turn off water supply, usually under sink, hot water side.
3 remove the mounting screws that you can see under the lip of the ledge when dishwasher door is open,once these are removed
4 carefully pull dishwasher out mindful of the hot water supply line that is attached.
5 visually locate the main shaft, use vise-grips to determine if shaft spins freely if not use v_grips to turn shaft two turns or so, check by closing the appliance door and turning power / water back on then try running unit.
this technique will work for some, and only if a (frozen) motor is the problem. this is a temp fix but it is better than nothing.
thanx good luck.

Apr 05, 2018 | Smeg Dishwashers

1 Answer

Loud smeg spin cycle


Open the loading door and place your hand at the top of the inner tub, close to the door opening and lift slightly. Inner and outer tub should move as one solid unit. If there is play between inner and outer tubs, you likely have a tub bearing issue. That is bad news, but repairable if you have the ability to DIY.
If the tubs seem good, then look for a sock between the inner and outer tubs. Often it is in the upper left corner (but could be anywhere) close to the door opening so that you can grab it with your hand or needlenose pliers. If you give the tub a spin you may be able to locate it by sight and feel, or with a flashlight from inside the tub through the drain holes. Also look for an object that may be stuck in one of those drain holes, like a screw, etc. Let me know if this is no help, we will look for other causes.

Jan 25, 2013 | Smeg WDI12 Front Load Washer / Dryer

1 Answer

The machine starts, does not heat the water, and just continues to run unless turned off manually. I am thinking either the timer or the heating element has failed. The machine is a model with the control...


hi test the element,the wires in the door can also break,it may be a thermostat/thermistor.if all these test ok it may be the pcb which is known as an intergrated these boards can be very expensive.

Jun 02, 2010 | Smeg 24 in. STX2 Built-in Dishwasher

1 Answer

Baumatic BFD60SS - Tablet not dissolving


this happened with mine and it turned out that the top shelf was too low, so this meant the spinning arm was being stopped by my plates. When the machine is fully loaded check that the spinners can move freely. if they don't then you can move the top shelf up a level. hope this helps

May 27, 2010 | Baumatic 24 in. BFD60SS Free-standing...

1 Answer

Water dripping from bottom off door during cycle where can I get a door seal


your overflow is most probably full, from turning off mid cycle and opening door and turning on again. take out of where it is tip up to a 45"angle water will come out, now don't turn off just open door.

Mar 27, 2010 | Smeg 24 in. DWI612 Built-in Dishwasher

2 Answers

Smeg integrated dishwasher continually washing - won't move to drying cycle.


you should check the heating element. if the water is not hot enough, the timer will not advance. crack open the door mid-cycle. let the water stop flying around. then open it all the way up. if you don't get a big ball of steam, you have an indication that your heating element may not be working properly. this is not too hard to check the resistance with a multimeter and then replace, if necessary. good luck

Nov 02, 2009 | Smeg STA4645U 18" Fully Integrated...

1 Answer

Whirlpool Gold Mod GU2500XTPQ1


sound like a low water level and or pressure issue. Start machine on normal cycle after filling open door and ck water level. should be up toJUST below heater assy.. assumiong htats good set hte wash arms to a set positon so you can watch for rotation. close the door adn after a few secs open rapidly and look for middle arm to be spinning, even the top 3rd row arm if present, should be spinning spinning . if not its possible that the motor/sumo assy is blocked w/ foriegn debris. remove the lower spray arm (hold the nut and spin arm)then remove 4 or 5 torx 15 screws. probly pretty glogged under there. if not id look into replacing motor sump assy/seals worn and not throwing water where it should go

Mar 03, 2008 | Whirlpool Gold 24 in. Built-In Dishwasher...

1 Answer

I have the same problem with dirty dishes on the top shelf and the utensil baskets


Dump the Kenmore on the seller's doorstep - when the place is full of customers!!

Dec 27, 2007 | Kenmore 24 in. 16264 Built-in Dishwasher

1 Answer

Smeg Dishwasher - model unknown


model numbers for dishwashers are generally where you can get to from the front, if they are noit on the front panel then look inside the door rim where the rubber seal is, either a small sticker on the door rim itself (inside) or where the door fits on the main cabinet, open the door fully to look for this sticker, sometimes placed under the front of the lid

Sep 28, 2007 | Smeg CSU2001 Built-in Dishwasher

1 Answer

Brand New Machine, can't open the door


Threre should be instructions on what you need to remove, but where is this black plastic located, and wher eis the screw positioned?

Apr 21, 2007 | Smeg DWI614 Built-in Dishwasher

Not finding what you are looking for?
Smeg DWI614 Built-in Dishwasher Logo

Related Topics:

218 people viewed this question

Ask a Question

Usually answered in minutes!

Top Smeg Dishwashers Experts

Marvin
Marvin

Level 3 Expert

85160 Answers

Norman Al-Anbar

Level 3 Expert

630 Answers

paul
paul

Level 3 Expert

825 Answers

Are you a Smeg Dishwasher Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...