Question about Dell OptiPlex GX260 PC Desktop

1 Answer

Cover was previously removed - Dell OptiPlex GX260 PC Desktop

Posted by on


1 Answer

  • Level 1:

    An expert who has achieved level 1.


    An expert that got 5 achievements.


    An expert who has answered 20 or more questions within one hour.


    An expert who has answered 20 questions.

  • Contributor
  • 70 Answers

You can go into the bios and one of the settings is 'cover remove alert' or similar words. you can give it 3 settings: on, off, clear

to stop the boot warning u must set this to CLEAR and save&quit.
then you must go in bios again and choose if u want the feature ON or OFF

Posted on Nov 20, 2013


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

How do you remove a throw out bearing on a 1997 harley

Step 1: Remove the magnetic drain plug with a wrench. (The drain plug is underneath the outer primary chain case on the left side of the motorcycle). Drain the fluid into a drain pan.
Step 2: Remove all of the screws on the clutch release cover with an Allen wrench. & also remove the clutch release cover. Discard the gasket that's located right on the inside of the clutch release cover.
Step 3: Loosen the clutch cable adjuster with a wrench to allow it to slack a bit in the clutch cable.
Step 4: Remove the retaining clip of the pushrod assembly with a pick tool. This should also release the two thrust washers located just behind the retaining clip.
Step 5: Remove the throw out bearing & Insert a new one into the same slot.
Step 6: Reinstall the two thrust washers and the retaining clip you previously removed.
Step 7: Tighten the clutch cable adjuster with a wrench.
Step 8: Replace the clutch release cover gasket and reinstall the cover by inserting and tightening the screws that you previously removed.

Aug 14, 2015 | Cars & Trucks

2 Answers

How do I change batteries?

To whom it may concern,

Remove the back panel on the remote, remove the dead batteries and install new ones in the same orientation that you found the previous ones in. Your remote is now ready to go.

Best of luck
Dish guy



Mar 15, 2015 | DISH Network IR Remote Control

1 Answer

1981 Yamaha xj750 seca. How do I change the starter clutch

No You Should be able to remove the one way starter clutch by removing the right-hand side cover and also removing the starter you can Utube the procedure im pretty sure but its pretty basic to do once your inside the cover and also you may wanna drain the oil previously to removing the side cover so it doesn't drain out on the floor while your trying to get cover off also be careful because there are dowels that align the case to the engine and sumtimes they rust together :)

Oct 14, 2014 | 1985 Yamaha XJ 700 S Maxim

1 Answer


I don't know your model but where the light previously was coming through a lens either remove the lens and replace the bulb or remove a square panel just opposite it on the side of the microwave to replace the bulb.

Nov 28, 2013 | Daewoo KOR-1B4H Microwave Oven

1 Answer

How to replace memory cards on a dell laptop D600


There's a great article found online from eHow with the following instructions:

Things you'll need:
  • SO DIMM 200-pin DDR SDRAM memory module
  • Phillips screwdriver

  • Shut down any currently running applications and turn off your laptop. Disconnect the power cord and any other attached cables. Remove any installed PC cards. Turn the laptop over and locate the battery compartment at the front edge of the device. Push the latch in the direction it indicates and remove the battery from the laptop.
  • 2 Examine the memory module cover, located next to the battery compartment. Unscrew the screw securing the memory module cover to the laptop. Remove the cover and set it aside.
  • 3 Push apart the clips located on either side of the currently installed memory module. Slide the module out of the socket and set it aside.
  • 4 Align the notch on the connector end of the memory module with the crossbar in the socket. Insert your replacement module into the socket and apply firm pressure until it is seated properly. Push the module downward until the clips lock it in place.
  • 5 Replace the memory module cover and screw it securely in place. Reinsert the battery into the battery compartment. Reinstall any previously removed PC cards and reconnect the power cable and any other previously disconnected cables. The laptop is now ready for use.

  • Hope this helps.

    Dec 23, 2010 | Computers & Internet

    1 Answer

    How do I remove the lamp on a optoma ep716?

    Lamp Replacing Procedure:
    1. Switch off the power to the projector by pressing the Power/ Standby button.
    2. Allow the projector to cool down at least 30 minutes.
    3. Disconnect the power cord.
    4. Use a screwdriver to remove the screw from the cover.
    5. Push up and remove the cover.
    6. Remove the 2 screws from the lamp module.
    7. Pull out the lamp module.
    8. Replace the lamp module in reverse the previous steps.

    Nov 11, 2009 | Optoma EP716 Multimedia Projector

    1 Answer

    Have driven Honda's all my life (55 YRS),bought a 2001 shadow spirit,found the battery,but how do I get it out (owners manual still wrapped beside it so I guess previous owner had same problem) G!! Paul

    • Remove the seat
    • Remover the ICM (Ignition Control Module) off the battery case cover
    • Remove the cover screw and case cover by releasing the case tabs from the cover slits
    • With the ignition switch off, disconnect the negative cable (black) first. Then disconnect the positive (red) cable
    • Remove the battery
    • Re-connect the POSITIVE cable first, then the negative.
    • Install balance of assembly in reverse order
    Please rate this answer. Thanks waddell 922!

    Apr 13, 2009 | 2001 Honda VT 750 DC Shadow Spirit

    2 Answers

    Back cover on psp

    What happened to the old cover? Did you remove it or is this a PSP you are fixing for someone that lost the parts?

    Mar 03, 2009 | Sony PlayStation Portable (PSP) Slim...

    1 Answer

    Water Filter removal/installation

    Bought the filter replacement and read the instructions. Turn off ice maker and replace filter. Remove by turning 1/4 turn to the right. pull out old filter. Remove cover, slide off, replace cover by sliding on the new filter. Push new filter in to the holding, hold so cover is horizontal, push in and turn back clockwise till the cover is horizontal to the floor.

    Feb 02, 2009 | Whirlpool GS6NBEXR Side by Side...

    1 Answer

    New Cover

    u need a kind of deviice often called "cluther"...that is easily available by local vendors...get it and replace ur handset cover 

    Jul 08, 2007 | Nokia 3250 Cellular Phone

    Not finding what you are looking for?
    Dell OptiPlex GX260 PC Desktop Logo

    Related Topics:

    54 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Dell Computers & Internet Experts

    Les Dickinson
    Les Dickinson

    Level 3 Expert

    18424 Answers

    Alun Cox

    Level 3 Expert

    2678 Answers

    Doctor PC
    Doctor PC

    Level 3 Expert

    7733 Answers

    Are you a Dell Computer and Internet Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides