Question about Dewalt 18 Volt Compact Drill Kit

Open Question

Hammer drill wont engage - Dewalt 18 Volt Compact Drill Kit

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 313 Answers

SOURCE: Cannot engage hammer action

the problem is the metal part of the clutch that meets the pin from the transmission. remove the 4 screw from the clutch & check if the the inside of the clutch & the trans pin meets. all you can do is to push back the metal parts of the clutch setting.

Posted on Jun 08, 2008

rowdy45176
  • 2176 Answers

SOURCE: dc925 hammer drill wont drill a hole

try shifting the high/low switch to make sure fully engaged. Also make sure that all the other positions are correct and if so then you have a clutch problem. For a breakdown you can go to Dewaltservicenet.com and get a parts breakdown and list for this tool. Good luck and if I have answered your question would you please rate this response accordingly.

Posted on Sep 19, 2009

  • 142 Answers

SOURCE: dewalt dw567

if i'm confused i'm sorry, but don't confuse and impact driver with a hammer drill

2 different tools altogether

Posted on Feb 27, 2010

  • 180 Answers

SOURCE: Hammer-mode engagement

there should be a slider type switch on top of the drill. and there will be a picture of a hammer, and a picture of a drill. slide accross to the drill picture for drill, and hammer for the hammer drill

Posted on Apr 07, 2010

Testimonial: "Wow, thanks a lot, great service"

  • 304 Answers

SOURCE: can't engage drill or hammer settings on de walt dc 925 xrp

Try turning the ring to 2 or 3 and run the drill holding the chuck so the clutch slips then try turning it to drill setting. Also try to do it in different speed settings. If not it sounds like a fault in the gear module. It might just be a metal clip just under the clip in side. Undo the 4 screws holding the gearbox onto the housing and carefully remove it, you might see the fault or loads of dirt that needs cleaning. Go to http://www.2helpu.com/world/map.aspx for a drawing.

Posted on Jun 02, 2012

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Demolition hammer model D25889 will not hammer motor turns on but not hammering


check the position of the operation lever
it should have 3 positions drill, hammer drill and hammer
make sure it is fully selected or the hammer action will not engage

Dec 31, 2015 | Hammering

1 Answer

Why bosch hammer drill not drilling


its possible the shaft used to engage the drill is broken, how old is the drill? Do you have it under warranty still? if its fairly new i'd return it and get a replacement for it.

Jul 20, 2014 | Bosch Drills

2 Answers

Torque limiter quick to engage Why?


Usually it is a worn clutch that will cause this.

May 26, 2014 | Drills

1 Answer

110 v comb drill does not engage to hammer setting


You don't say which model or make. could be just the selector.

Oct 19, 2012 | Drills

1 Answer

On my BOSCH CSB 470-RLE 470w electric drill the chuck is slipping i can hold it in my hand and it wont move


It is a spring loaded hammer drill. You need to push the chuck down just a bit for it to engage the clutch. If it is still slipping then either the clutch pieces (items 23 and 32) are worn or item 32 is spinning freely on the spindle shaft. Here is a parts diagram.

Bosch CSB470-RLE diagram

Aug 16, 2012 | Bosch Drills

1 Answer

Hammer-mode engagement


there should be a slider type switch on top of the drill. and there will be a picture of a hammer, and a picture of a drill. slide accross to the drill picture for drill, and hammer for the hammer drill

Apr 07, 2010 | Dewalt 18 Volt Compact Drill Kit

1 Answer

Drill works fine but wont engage hammer. the torque ring goes from 1 to 21 ok but i cant engage the drill or hammer setting


On my DW988 the ring would go past 21 a couple of clicks to a symbol that looks like a yellow T and that would be hammer mode when I press down to drill.

Nov 18, 2009 | Dewalt DC925 Cordless Drill

1 Answer

New bosch psb 550 re with hammer action. Hammer action does not seem to engage. even with 5mm bit progress is non existent. The bits were bosch masonary bits and I was drilling into concrete blocks


your pin under the selector switch my have broken off. also the hammer rod could have broken too. if its drilling and not hammering that more likely. you may be under warranty call bosch or log on and go to dealer locator's for the closes dealer to you. hope this helped

Oct 09, 2009 | Bosch Power Tools Hammer Drills

1 Answer

The motor turns but the clutch will not engage


Take the drill out of the hammer drill setting when in reverse.  Using the drill setting with the speed on 1 will give the power to free the bit.  If the clutch will not engage, GENTLY but firmly switch between forward and reverse.  This should work just fine.   I hope this solution brings you success!  Best Regards,  Michael Mittelsdorf

Dec 26, 2008 | Drills

Not finding what you are looking for?
Dewalt 18 Volt Compact Drill Kit Logo

Related Topics:

25 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dewalt Drills Experts

Doctor PC
Doctor PC

Level 3 Expert

7733 Answers

yadayada
yadayada

Level 3 Expert

75822 Answers

Jim Thurston

Level 3 Expert

670 Answers

Are you a Dewalt Drill Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...