Question about Tools & Hardware - Others

Open Question

Bostitch b5 stapler

I have a vintage Bostitch B5 stapler at work and can't figure out how to open it. The front plat says to "push then pull to load" but it has me stumped. Maybe it's jammed? Maybe I'm just daft? Does anyone have experience with these old timers?

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 1 Answer

SOURCE: B310HDS Stanley Bostitch stapler rod to lock stapes has plastic t

I have the same problem and have found no answers from Stanley Bostitch customer service. They redirect to a telephone number that does not answer.
Solution: Don't buy Stanley Bostitch.

Posted on Feb 02, 2010

Ad
  • 497 Answers

SOURCE: i need a manual for bostitch miiifs floor stapler

www.online-manuals.com

Posted on Nov 06, 2009

  • 18 Answers

SOURCE: I have a bostitch M3FS floor stapler that only

You could try finding your stapler and repair solutions oneReplacementParts.com They have parts, and guides to help repair this stuff.

Posted on Jan 05, 2010

  • 34 Answers

SOURCE: I have a very old Bostitch staple gun Model T5.

You should not need any tools to lift the guard/nose piece. The T5 nose piece cleary has engraved on it "Pull Up To Insert Staples". To remove old staples, use a pencil or similar rod to depress the hammer/striker above the staples while the nose is open.

Posted on Aug 07, 2010

  • 50 Answers

SOURCE: How do I replace the

"The staples load from the rear of the stapler. At the back end of the is a piece of black plastic that extends beyond the end of the stapler. This device holds the staples inside the stapler. To open the area where the staples are placed, push this extended button and lift up on it. The spring device that holds the staples inside the stapler will then slide out. Place a new strip of staples inside the stapler on top of the two metal guide rails. Then insert the spring device to lock the staples in place. The stapler is now loaded and ready to work. " hope this helps you out

Posted on Jan 06, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Open and load staples b660


Hold on to the chrome part near where the staples come out and lift up on the top plastic part. There is a video link on the Bostitch site to the right midway down the page
Stanley Bostitch No Jam Premium Stapler B660 Black

Feb 08, 2015 | Stanley Bostitch B660-BK: NoJam Full Strip...

2 Answers

How do i load the Stanley Bostitch 00540


Hi Diane,

If you look at the back of the stapler, there's a bright red button. Push this in and slightly lift up at the same time, then magazine is withdrawn. Feed a strip of staples in and replace the pusher unit.
Bostitchtools co uk Bostitch Nailers Staplers Fasteners Coil Nails Staples

Jan 29, 2015 | Stanley Bostitch 00540: 00540 AntiJam ?...

2 Answers

Bostitch electric stapler wont open


Hello, Go to this website for support number and downloading of the operators manual for the model of stapler. Bostitch Office Products Staplers Pencil Sharpeners Hole Punchers Tools...

May 01, 2014 | Stanley Bostitch B8 Electric Stapler

1 Answer

I have a bostitch electric stapler B5E6J-3. Cannot figure out how to load the staples, please help!


For reference if you cannot push up the metal face and pull it out to replace staples there could be a jammed staple that has to be removed with pliers.

Jul 31, 2013 | Air Tools & Compressors

1 Answer

I inherited a Bosch T31 bradder and stapler. Couldn't get any help at Home Depot chosinga nails. Bought Porter Cable 16 Ga. 1" finish nails (PFN16100-1). Released arm and slid the nail carrier...


BOSTITCH T31-1 stapler & T31-2 STAPLER and NAILER. Both use 18 gauge (very fine gauge wire). Try using 18 gauge Bostitch staples (used in BT model bostitch staplers). Good Luck

Feb 03, 2011 | Stanley Bostitch N80CB Coil Framing Nailer

1 Answer

How do I replace the staples in Stanley Bostitch B310HDS? I cannot seem to figure out how to open it.


"The staples load from the rear of the stapler. At the back end of the is a piece of black plastic that extends beyond the end of the stapler. This device holds the staples inside the stapler. To open the area where the staples are placed, push this extended button and lift up on it. The spring device that holds the staples inside the stapler will then slide out. Place a new strip of staples inside the stapler on top of the two metal guide rails. Then insert the spring device to lock the staples in place. The stapler is now loaded and ready to work. " hope this helps you out

Jan 06, 2011 | Stanley Bostitch 00540: 00540 AntiJam ?...

1 Answer

How do i load the staple gun?


1 Hold stapler upside down.
2. Release black plastic catch at rear and pull out.
3. Drop staples into bottom of gun, with open side up.
4. Push black plastic catch closed and latched.

wallyp

Oct 30, 2010 | Stanley Bostitch Pc4000oc2 Outward Clinch...

9 Answers

I have a very old Bostitch staple gun Model T5. It has run out of staples, but I cannot figure out how to put new staples in it.


You should not need any tools to lift the guard/nose piece. The T5 nose piece cleary has engraved on it "Pull Up To Insert Staples". To remove old staples, use a pencil or similar rod to depress the hammer/striker above the staples while the nose is open.

Dec 23, 2009 | Stanley Tools & Hardware - Others

Not finding what you are looking for?
Tools & Hardware - Others Logo

Related Topics:

344 people viewed this question

Ask a Question

Usually answered in minutes!

Top Tools & Hardware - Others Experts

Doctor PC
Doctor PC

Level 3 Expert

7733 Answers

Brad Brown

Level 3 Expert

16037 Answers

J.D. Browning
J.D. Browning

Level 3 Expert

2760 Answers

Are you a Tool and Hardware - Other Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...