Question about Dewalt 6.3 Amp Dry Wall Screwdriver

Open Question

Can't change the end bit - Dewalt 6.3 Amp Dry Wall Screwdriver

Posted by Anonymous on

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Fixya


You can change to any bit, but have to change the compression collar inside the end of the shaft. For example if the tool shaft size is 1/8" you need to use the 1/8" collar etc. Make sure you use the corresponding bit with the corresponding compression shaft size or the bit will not lock in position when you tighten the collar.

Aug 10, 2014 | Dremel Tools & Hardware - Others

1 Answer

Top chuck just clicks but won't change bit size?


It sounds as though you will have to replace the chuck. Remove the screw (l/h tread) from inside the chuck first before removing it.

Feb 02, 2013 | Drills

1 Answer

How do I change bits....have not used router in years


Most routers have a "Pin" that can be depressed to lock the router spindle. But first, rotate the spindle to match a small hole in the spindle with the pin. With the spindle locked in place, use a wrench (routers often come with this) to loosen the "collet" which holds the router bit. The collet nut will turn counterclockwise when loosening the nut, when looking directly at the bottom end of the router bit, i.e. when looking down at the router when the router itself is up side down.

To install a bit, reverse the process above. Do not overtighten. About a on-eighth turn past handtight will suffice. The collet or the threaded end of the spindle can be stripped out.

Hope this helps.

Apr 27, 2011 | Garden

1 Answer

Have never used a hand dill, how do i change the drill bit. i need to drill a small hole. thank you anne


Typically, the end of the drill where the bit is inserted (called the 'chuck') rotates to loosen or tighten the arms holding the bit in place. Grasp the top of the drill with one hand and rotate the end the bit is inserted into counter-clockwise if the bit end is pointed towards you to loosen the arms and release the bit.

If it is an older drill it may have a 'key' that would look similar to end of a phillips screwdriver on a tee that can be inserted into where the chuck and the rest of the drill assembly meet and twisted to loosen the bit.

If neither of these work post what type of drill you are using as not all hand drills are the same. Hope this helps.

Dec 10, 2010 | Garden

1 Answer

Hilti te 10 - how do I change the bit ? and lock it good...


The end of the drill is 2 parts hold the bottom part(closes to the drill) and turn the top part (the end the bits in) and turn it a 1/4 turn counter clockwise that opens the chuck then pull the bit out to replace do the opposite. Don't let the end at the drill spin or it will come off the drill completely if that happens simply line it back up and tap it hard to get it back on

Nov 25, 2010 | Hilti Hammer Drill Bit TECX 1 In x 10 In...

1 Answer

Can you give me step by step on how to change drill bits on the Mastercraft Souce One 18V Cordless Drill.


pull the collar on the front forward and insert hex end of bit in and let collar go back. this locks the bit in.

Aug 29, 2010 | Bosch PS20 2 Factory Reconditioned 10.8V...

1 Answer

I can't change the bit on my Bosch PSB 650 RE drill


see if there's not secured to the shaft with a screw inside at the bottom of the bit. try to slack it by turnig it clockwise. then catch a 19 mm. open end spanner in a bench wise put the shaft with its two flat sides in the spanner and with a pump pliers catch the bit and unscrew the bit turning counterclockwise this time

Oct 03, 2009 | Bosch Drills

3 Answers

I borrowed a black and decker rotary tool (RT 550). I can't seem to get the bit off or be able to change bits. There is no tool to use to open the bit and everywhere on-line it says ''quick swap of bit...


slide the orange on/off switch all the way back then push in the black button the switch slides over. This will lock the shaft-then use small wrench provided w/ tool to turn the collet nut

Jul 13, 2009 | Tools & Hardware - Others

1 Answer

How to change drill bit on black & decker plus pivot cordless drill How to change the bit on a Skil cordless screwdriver 2362 with a keyless check?


Grab the end of the chuck in one hand, and the outer ring of the chuck nearer the motor, and twist the chuck end. try both directions until it loosens.

Jan 28, 2009 | Drills

Not finding what you are looking for?
Dewalt 6.3 Amp Dry Wall Screwdriver Logo

Related Topics:

31 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dewalt Tools & Hardware - Others Experts

John Trevino

Level 3 Expert

1383 Answers

Doctor PC
Doctor PC

Level 3 Expert

7733 Answers

john h

Level 3 Expert

10993 Answers

Are you a Dewalt Tool and Hardware - Other Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...