Question about Tools & Hardware - Others

1 Answer

Stanley tre550 Stapler won't fire even when pressed down on material

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 7 Answers

Buy another one

Posted on Dec 03, 2013

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
  • 384 Answers

SOURCE: My Stanley T-50 will not fire staples when the

Stapler is clog. Clean out the magazine.

Posted on Aug 31, 2009

  • 187 Answers

SOURCE: have a stanley tre550 and need to know how to use

The staples are NOT loaded on top of the pull out shaft; they are inserted directly into the slot that opens when you pull the shaft out. If the nose of the tool is not placed firmly against a surface, it will not fire. Go to Stanley’s website’s knowledge base and type in the model number, and you can get a PDF of directions. http://www.stanleytools.com/default.asp?TYPE=STATICLEFT&PAGE=Support.htm&LEFT=left_support.htm Below is the graphic from their pdf. Here is a step by step: Unplug the tool. Squeeze the end of the shaft at the rear bottom of the tool and pull out the shaft. Flip the tool over on it’s back. Insert the staples, (points up) and then slide the shaft back in. Plug it in, press the on button (under the the power cord in the back). Press the nose squarely against the material and press the trigger.c901269.jpg

Posted on Oct 15, 2009

  • 288 Answers

SOURCE: How do you load nails into a stanley tre550 nail

there should be a button on the bottom rear of the gun, when you press it, it should release a bar that you pull back. the nails go in the dirction you nail them. sometimes the clips are too big for the guns and you have to break about an inch off of them

Posted on Dec 06, 2009

blueextc3221
  • 15935 Answers

SOURCE: Don't know how to load stapler tre550

The staplesare NOT loaded on top of the pull out shaft; they are inserted directlyinto the slot that opens when you pull the shaft out. If the nose ofthe tool is not placed firmly against a surface, it will not fire.

CLICK HERE
and click the PDF icon on the right of the model # to start the download.

Here is a step by step:
Unplug the tool.
Squeeze the end of the shaft at the rear bottom of the tool and pullout the shaft.
Flip the tool over on it’s back.
Insert the staples,(points up) and then slide the shaft back in.
Plug it in, press the on button (under the the power cord in the back). Press the nose squarely against the material and press the trigger
.

Thanks for using FixYa - a 4 THUMBS rating is appreciated for answering your FREE question.

Posted on Mar 06, 2010

  • 221 Answers

SOURCE: I cant load the brads

You can go to http://www.stanleytools.com/default.asp?TYPE=STATICLEFT&PAGE=Support.htm&LEFT=left_support.htm

Click on Knowledge base and search for your model. I found it but I am unable to attach a copy here.

Posted on May 06, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

How do I load the stapler?


No you don't. We answer most things here.

If the stapler is like any of these

http://www.amazon.com/s?ie=UTF8&page=1&rh=i%3Aaps%2Ck%3Abostitch%20staple%20gun

You push the back in slightly to unlatch it and then drop it down a bit and the staple pusher comes out completely.

Jan 28, 2016 | Heavy Duty Stanley Bostich Heavy-duty...

1 Answer

Does the tre550 have thermal cut out


There is a piece in side the stapler that may have broke as it did with me

Jun 19, 2014 | Stanley Tools TRE550 Electric Staple/Brad...

1 Answer

Been using stapler for past hour suddenley trigger


Could be a bad power cord: broken wire at the switch; a bad switch; the stapler needs lubrication; or the stapler is shot.

Jun 19, 2014 | Stanley Tools TRE550 Electric Staple/Brad...

1 Answer

Won't fire even when pressed hard against the material


how old is this tool, if it is new take it back to where you bought it, most people try to repair them and get hurt in the process, if you have a repair center in your town take it to them and they will help you

Nov 18, 2013 | Stanley Tools TRE550 Electric Staple/Brad...

1 Answer

Problem with the Stanley Tools TRE550 Electric Staple/Brad Nail Gun Cannot get the staple drive flush help me please


First, try holding the stapler very firm to your project and make sure that the piece that you staple in to is backed solid with no give or springiness.
second, you might try shorter staples,or . . try dialing in more tension by turning the big knob on the back end that has the "+" "-"

Sep 11, 2011 | Stanley Tools TRE550 Electric Staple/Brad...

1 Answer

Don't know how to load stapler tre550


The staplesare NOT loaded on top of the pull out shaft; they are inserted directlyinto the slot that opens when you pull the shaft out. If the nose ofthe tool is not placed firmly against a surface, it will not fire.

CLICK HERE
and click the PDF icon on the right of the model # to start the download.

Here is a step by step:
Unplug the tool.
Squeeze the end of the shaft at the rear bottom of the tool and pullout the shaft.
Flip the tool over on it’s back.
Insert the staples,(points up) and then slide the shaft back in.
Plug it in, press the on button (under the the power cord in the back). Press the nose squarely against the material and press the trigger
.

Thanks for using FixYa - a 4 THUMBS rating is appreciated for answering your FREE question.

Nov 17, 2009 | Electric Stanley Tre500 Staple Gun /...

2 Answers

How do you load staples into the gun?


The staplesare NOT loaded on top of the pull out shaft; they are inserted directlyinto the slot that opens when you pull the shaft out. If the nose ofthe tool is not placed firmly against a surface, it will not fire.

CLICK HERE
and click the PDF icon on the right of the model # to start the download.

Here is a step by step:
Unplug the tool.
Squeeze the end of the shaft at the rear bottom of the tool and pullout the shaft.
Flip the tool over on it’s back.
Insert the staples,(points up) and then slide the shaft back in.
Plug it in, press the on button (under the the power cord in the back). Press the nose squarely against the material and press the trigger
.

Thanks for using FixYa - a 4 THUMBS rating is appreciated for answering your FREE question.

Aug 07, 2009 | Stanley Tools TRE550 Electric Staple/Brad...

1 Answer

Have a stanley tre550 and need to know how to use


The staples are NOT loaded on top of the pull out shaft; they are inserted directly into the slot that opens when you pull the shaft out. If the nose of the tool is not placed firmly against a surface, it will not fire. Go to Stanley’s website’s knowledge base and type in the model number, and you can get a PDF of directions. http://www.stanleytools.com/default.asp?TYPE=STATICLEFT&PAGE=Support.htm&LEFT=left_support.htm Below is the graphic from their pdf. Here is a step by step: Unplug the tool. Squeeze the end of the shaft at the rear bottom of the tool and pull out the shaft. Flip the tool over on it’s back. Insert the staples, (points up) and then slide the shaft back in. Plug it in, press the on button (under the the power cord in the back). Press the nose squarely against the material and press the trigger.c901269.jpg

Mar 29, 2009 | Stanley Tools TRE550 Electric Staple/Brad...

Not finding what you are looking for?
Tools & Hardware - Others Logo

Related Topics:

50 people viewed this question

Ask a Question

Usually answered in minutes!

Top Tools & Hardware - Others Experts

Doctor PC
Doctor PC

Level 3 Expert

7733 Answers

Brad Brown

Level 3 Expert

15667 Answers

J.D. Browning
J.D. Browning

Level 3 Expert

2760 Answers

Are you a Tool and Hardware - Other Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...