Question about Xerox Office Equipment & Supplies

Open Question

Scanning from workcentre 3045

All seems to go fine until a "no" response is entered to the question "another page?" when the following message appears: SMB Error 031-529 Scan. Log-in failed.

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 1 Answer

SOURCE: SMB Scanning

I had the same issue and fixed it by adding the group "Everyone" to the shared folder permissions (where I was sending my scans) and assigning the "Everyone" group rights to "change" and "read".

Posted on Jan 20, 2009

Ad
  • 1 Answer

SOURCE: Scan job returns error job is done improperly. Check log 6385

I had this problem when sending to mail account.
This can also be changed for ftp/smb.
So maby this is the answer to you problem.

Solution: Extend the time-out from 90 to 300 seconds

Goto the setting of the machine (http://<ip>) and login with Administrator account.
On the page Network click on Email/SMTP.
Change the Time-Out setting to 300 seconds.

Good Luck!

Greets,
Ivan

Posted on Mar 18, 2009

  • 1 Answer

SOURCE: KM 3060 Scan Error 2101

Hi Guys,
I was getting the 2101 error as well. I resolved this by placing the IP address of the computer into the "host name" field. Only thing to remember is that your IP address will change from time to time. You will need to assign a static IP to that particular machine or give it a reserved IP address through your switch. Good luck!

Posted on May 27, 2009

herminio_hal
  • 210 Answers

SOURCE: How to setup scan to pc on Konica minolta bizhub 350 Error ED09C7

Your configuration sharing SMB folder is incorrect. Create desktop folder rename all upper case SMB right click on the folder and click sharing and set full control to everyone. Go to web brouser type in the ip address of the printer log on to administrator password 8 zeros or 12345678 and change the setting.

Posted on Jul 09, 2009

  • 11 Answers

SOURCE: I am getting an error message 027-516 server

SMASH IT WITH A HAMMER NOWWWWWWWWWW

Posted on Nov 17, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I reset xerox 3045


Try this:

1. To reset the NVRAM (this holds the control panel settings), turn off the printer.
2. Press and hold the On Line (0) and Enter (4) buttons, and turn on the printer. Keep the On Line (0) and Enter (4) buttons depressed until the message "Initializing...Please Wait" appears on display (this takes about one minute).
3. Release the On Line (0) and Enter (4) buttons and wait for the front panel to display "Ready." This takes about 45 seconds.
4. Press the Menu Up (1) button until the Reset Menu is displayed.
5. Press the Item Up (2) button until Factory Defaults is displayed.
6. Press the Value Up (3) button to display the choices. To actually reset the factory defaults you would select "Yes."

Aug 03, 2016 | Xerox WorkCentre 3045ni Multifunction...

1 Answer

How to print a configuration page on a m20i


We encourage you to use our knowledgebase, MRC Smart Technology Solutions is here to help! We offer a program to cover up to 3 printers of any manufacturer for an entire year!
We can solve your problem!
Email patrick@mrc360.com for more info.
Solution : Print a Connection Page (Network Connectivity Report / Configuration Page) NOTE: Print the Connection Page to locate the TCP/IP Address for the WorkCentre.
  1. Press the [Machine Status] button on the Control Panel. 'Machine Setup' will be displayed on the Display Screen.

    m20-cntl-pnl-status.jpg
  2. Press the [Up or [Down] arrow button until 'Reports' is selected, and then press the [Enter] button.
  3. Press the [Left] or [Right] arrow button until 'Connect Page' is displayed, and then press the [Enter] button to print the report.
  4. Press the [Stop] button to return to the Standby mode.

    m20-ctrl-pnl-3.jpg
http://www.support.xerox.com/support/workcentre-m20-m20i/support/enus.html

Oct 13, 2014 | Xerox WorkCentre M20i All-In-One Laser...

1 Answer

Help! I'm trying to print a configuration page on a WorkCentre M20i


Hi, you can print a configuration page on the M20i by following the steps below:
- Press the Machine Status button - Select Reports, then press Enter - Select Connect Page, then press Enter
The configuration page will print out. For configuration page instructions for other copiers or printers, visit the How to print config pages website.

Jun 02, 2011 | Xerox WorkCentre M20i All-In-One Laser...

2 Answers

How do I get a meter reading of number of copies?


Here you go.

  1. Press the [Reports] button on the Control Panel

    m15-console-report-but.jpg

  2. Press the [Up] or [Down] arrow until 'Systems Data' is displayed on the Display Screen.
  3. Press the [Enter] button.

    The System Data list will be printed with the following information:
    • Total Page Counts: Total number of pages printed
    • CRU Prints: Number of pages printed using the current Toner (Dry Ink) Cartridge
    • Replaced Toner Counts: Number of new Toner Cartridges installed in the machine
    • Replaced Drum Counts: Number of new Drum Cartridges installed in the machine
    • Current Drum Page Counts: Number of pages printed using the current Drum Cartridge
    • Platen Scan Page Counts: Number of pages scanned using the Document Glass
    • ADF Scan Page Counts: Number of pages scanned using the Automatic Document Feeder (ADF)

Feb 10, 2010 | Xerox WorkCentre M15i Laser Printer

1 Answer

Xerox WorkCentre 4150, 3 vertical white lines in all feeder scans


the problem is in the scanner, open it up and see if you can find any smudges, and clean any obstruction, any ink, liquid eraser residuals, can cause this part to appear as lines on your copied faxed image.
dont concentrate on the printer this is a scanner problem

Jul 28, 2009 | Xerox WorkCentre 4150/X Laser Printer

1 Answer

Changed black cartridge. Machine works fine, but


To align the cartridge from the control panel:

Please follow the steps given below:

1. Please Load a plain paper.
2. Press and hold the "Scan" button for three seconds.
3. An alignment page prints.
4. Place the alignment page onto the scanner glass.
5. Press the "Scan" button.
6. Once scanning is complete, the cartridge has been aligned for optimal print quality. Alignment must be complete before continuing with any print jobs.

Apr 19, 2009 | HP OfficeJet 6110 All-In-One InkJet...

4 Answers

I wish to read the total copy count on Xerox WorkCentre M15i


You have to print out the meter report.
  1. Press the [Reports] button on the Control Panel

    m15-console-report-but.jpg

  2. Press the [Up] or [Down] arrow until 'Systems Data' is displayed on the Display Screen.
  3. Press the [Enter] button.

    The System Data list will be printed with the following information:
    • Total Page Counts: Total number of pages printed
    • CRU Prints: Number of pages printed using the current Toner (Dry Ink) Cartridge
    • Replaced Toner Counts: Number of new Toner Cartridges installed in the machine
    • Replaced Drum Counts: Number of new Drum Cartridges installed in the machine
    • Current Drum Page Counts: Number of pages printed using the current Drum Cartridge
    • Platen Scan Page Counts: Number of pages scanned using the Document Glass
    • ADF Scan Page Counts: Number of pages scann

Apr 19, 2009 | Xerox WorkCentre M15i Laser Printer

1 Answer

H4 message call service


Performing a Fault Reset 14 will reset your WorkCentre and will help to clear error codes.
  1. Find the pink Clear button on the Control Panel of the WorkCentre.
  2. Find the button below the word Auto.
  3. Press these buttons in the following sequence: [Clear], [Auto], [Clear], [Auto] NOTE: All of the lights on the Control Panel should go out and the LED Display should go blank. If the lights do not go out, then repeat step 3 until they do. It may be necessary to increase or decrease the pace of the [Clear], [Auto], [Clear], [Auto] sequence.
  4. Press the [10's] key one time and the [1's] key four times to enter '14' in the LED Display, as if you were to make 14 copies.
  5. Press the green [Start] button.
  6. Press the pink [Clear] button two times.
  7. The WorkCentre should now warm up and come to ready.
  8. If the above steps do not clear the error code, repeat steps 3 to 6 a second time.

May 27, 2008 | Xerox WorkCentre XD125F All-In-One Laser...

Not finding what you are looking for?
Office Equipment & Supplies Logo

Related Topics:

482 people viewed this question

Ask a Question

Usually answered in minutes!

Top Xerox Office Equipment & Supplies Experts

Xeroxrep

Level 1 Expert

33 Answers

Philip Hughes

Level 2 Expert

72 Answers

CheckitRight
CheckitRight

Level 3 Expert

1362 Answers

Are you a Xerox Office Equipment and Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...