Question about Lenze AC Tech Lenze 8100 AC Drive Inverter

Open Question

Oc3 fault ....what are the causes checked motor and checked for binds everything seems normal

Posted by Anonymous on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

KitchenAid Mixer struggling to spin?


Check everything you have done for a mistake, the pin through the planetary, the pin through the fuse gear and the pin in the main shaft that drives the bevel gear. That's the gear that pinion gear on the fuse gear shaft mates with. After that you are left with a fuse gear fault. I am assuming that the motor is turning at normal speeds and not somehow binding up, no reason why it should as motor stays in one piece during gear changing procedure.

Apr 18, 2014 | KitchenAid Food Mixers

1 Answer

Replaced starter clutch pack without a manual or the proper knowledge on doing this now were screwed up on the timii beleave cause motor seems to bind up when we turn it over by hand help us dummies p


replacing the starter should not impact time. best thing for you to do is remove and double check everything as you reassemble, including comparing the new to the old starter.

Jul 23, 2013 | Yamaha Motorcycles

1 Answer

Rear wheels lock up at times,dont do it with heavy load. checked brakes,seems ok. pulled rear axels out drivers side splines worn,all bearing seems ok


look in rear diff. worn gear is binding up. not going to last long. fix now before it blows the whole carrier and everything.also A worn U joint in driveshaft could cause this

Mar 15, 2013 | 2000 Chevrolet Silverado 1500

1 Answer

Inverter error OC3 (over current fault)


Here is a complete guide must have Adobe Reader it's PDF... You will find the error code in this manual and more information on it.

http://www.stroeter.com/preview/_upload/51_00_ENG.pdf?documentID=4934

Mar 25, 2012 | Electronics - Others

1 Answer

Recoil pulley assembly keeps binding. Rope stays in pulley, but won't retract. Must remove motor housing , loosen 3 pulley hold down guides, & uncock the pulley. spring tension on recoil is fine....


Have you ever replaced the recoil rope, if you had is it a larger rope then the one that came with it? If so, that could be the cause of the binding. I had that difficulty once.

Aug 05, 2011 | Garden

2 Answers

When I press the button to make the automatic rear door open it comes up halfway and then reverses. What is causing this?


internal problem with the motor causing high resistance or binding hinges or something binding making the motor have to push harder than normal.

May 30, 2011 | 2008 Chevrolet Tahoe

1 Answer

My pedal oc3 does the octav , but it makes not at the same time I play


A very slight delay would be normal as it takes the pedal electronics time to acquire and creae the second harmonic. The ear is sensitive to about 1/1000 second. You haven't said how much delay it is causing... If it is over 1/20 of a second there is a problem.

May 05, 2011 | Roland Boss OC-3 Pedal Octave/Synth

1 Answer

System error E010


A specific revolution is not detected from the main motor rotation detection
signal (MLOK*), causing the signal to go '1'. (main motor fault)
Possible cause .
The main motor (M101) is faulty. The controller PCB is faulty.
1) Connector
Is the connection of the connector (J903) of the main motor and the
connector (J06) on the DC controller PCB normal?
NO : Correct the connection.
2) Main motor (M101), DC controller PCB
Try replacing the main motor. Is the fault corrected?
YES : Replace the main motor.
NO : Check the wiring; if normal, replace the DC controller PCB.

Dec 30, 2010 | Canon iR1600-2000 PS

2 Answers

DC440st


This problem can be a bad main motor. The motor has gears on it and they can bind when they are worn. The motor assembly itself electrically can be bad.
If there is something binding in the gear train assembly this can cause the motor not to turn. A bound up copy cartridge can cause the motor not to turn.
A bad board can also cause this not to start.
To replace the main motor, it is very detailed and time consuming.
Try a service call, hope it is cheap enough and the copier is in good shape besides the motor being bad.

Dec 30, 2009 | Xerox DC440ST Copier

Not finding what you are looking for?
Lenze AC Tech Lenze 8100 AC Drive Inverter Logo

Related Topics:

102 people viewed this question

Ask a Question

Usually answered in minutes!

Top Lenze AC Tech Electronics - Others Experts

Donald DCruz
Donald DCruz

Level 3 Expert

17130 Answers

kakima

Level 3 Expert

102366 Answers

Brad Brown

Level 3 Expert

15995 Answers

Are you a Lenze AC Tech Electronics - Other Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...