Question about Epson Stylus CX3200 All-In-One InkJet Printer

2 Answers

Scanner error the red light is on and the message scanner error. tried turning it off and then on again after a few seconds the red light comes on again. Also check to see if the system was locked released that. Tried to reset nothing.

Posted by on

  • 2 more comments 
  • turi Nov 18, 2007

    scanner error

  • Navyav8r Dec 19, 2007

    I have the same problem....Scanner Error...see manual. Tried resetting the lock function, but did not work. Now what? It has been a great printer for me up until now.



    MikeB

  • Anonymous Dec 30, 2007

    scanner warning up the error message scanner not ready. I have tried turning the printer on and off and locking and unlocking.



    Still have the problem

  • sandwoman Mar 19, 2008

    scanner error with red light on. I turned it off and on and even switched the lock and unlock position and even lightly shook it like they said no luck

×

Ad

2 Answers

  • Level 1:

    An expert who has achieved level 1.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 2 Answers

Try flicking the transportation lock (on the left side under the scan lid) on and off. It has a picture of a pad lock shown locked and unlocked. Flip it back and forth and leave it in the unlocked position.

This worked for me. Good luck!

Posted on Oct 17, 2007

Ad
  • Level 1:

    An expert who has achieved level 1.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 1 Answer

Had this problem for over a year now. Lock down the transportation tab. pick it up and shake lightly. unlock. Good to go for a month or so. Hey, when it prints it's great.

Posted on Jan 09, 2008

Ad

2 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

  • 2 Answers

SOURCE: the red light is on and the message scanner error.

Try flicking the transportation lock (on the left side under the scan lid) on and off. It has a picture of a pad lock shown locked and unlocked. Flip it back and forth and leave it in the unlocked position.

This worked for me. Good luck!

Posted on Oct 17, 2007

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Everytime I turn my printer on (Epson Artisan 700 series printer) it waits for about 5 to 7 seconds and then displays a message that says "A scanner error has occured. Please see your...


when I turn my printer on (Epson Artisan 700 series printer) it waits for about 5 to 7 seconds and then displays a message that says "A scanner error has occured. Please see your documentation". Then all the lights start flashing, And then I cant do anything, but turn the printer off.

I have turned it off and unplugged it and tryed again always same result.

bdl12920@aol.com

May 10, 2011 | Epson Stylus Multifunction Inkjet Printer/...

2 Answers

KV-S2026C not scanning


does this unit show any error?

how old is this unit> is it under warranty?

Oct 02, 2008 | Panasonic KV-S2026C Pass-Through Scanner

1 Answer

Scanner stopped in middle of scan . green light in front went out. later red light came on. message on screen said that the carriage was locked. I tried turning scanner on and off and green light comes on...


test the power supply to the scanner also test the leads that attach from the power supply to the scanner if its connected to a computer you might have to uninstall it then reinstall it this applies the driver aswell you can do this control panel admistrive tools,computer management,device manager scroll down you should see a yellow question mark? right click to reinstall drivers or ports(com&lpt)ECP printer port right click update driver
hope this helps

Oct 27, 2010 | Computers & Internet

1 Answer

My cx3200's control panel reads scanner error. I unlocked the transportation lock, turned off, turned on. It stayed off for about 2 minutes then came right back on. While the error light was off tried to...


The only things that can cause a scanner error on this unit is a complete scanner harware failure or the scanner lock. With the unit on lock the transport lock and unlock it a few times quite forcibly. Then leave it in the unlocked position and power off and on again. If the light returns then at his point I think a new printer will be needed.

Jan 18, 2010 | Epson Stylus CX3200 All-In-One InkJet...

3 Answers

2003 saturn vue service light on with wrench how do I reset


Open the hood. You will notice there is a large black box on the right-hand side directly behind the battery. This black box is the fuse box. Pull the top of the fuse box off. There are two clips on either side; once you pop one side, the other comes off very easily. In the top left-hand side of the fuse box where all the fuses sit, you will see a large orange/red block. Below this block is a button that says "reset." Press this button for 5 seconds. Turn the car on and wait for a minute. If the light does not go on, turn off the car and set the key to ACC on the key ring. Push the reset button again, holding it for a total of 15 seconds. Turn the key to off, take out the key, return the key and start the car again. Allow the car to run for 2 full minutes. It is taking the system a few minutes to register that this button has been pressed.

Sep 01, 2009 | 2003 Saturn VUE

2 Answers

Rinnai Energysaver 1004F on indicator light is red (usally green)


If its not producing heat, yep! If it is, it indicates that there is an error code stored in memory.

Feb 18, 2009 | Rinnai RHFE-1004FA 38,400 BTU Energy Saver...

1 Answer

Red light comes when powered


Please try the following to resolve your issue:
1. Unplug the USB cable and the AC adapter from the back of the scanner.
2. Toggle the Transportation lock (located on the bottom of the scanner) back and forth 5 times, ensuring that the lock is all the way in the unlock position.
3. Reconnect the USB cable and the AC adapter cable, and then try to scan.

Jan 04, 2008 | Epson 2580 Perfection Photo Scanner

1 Answer

The red light is on and the message scanner error. tried turning it off and then on again after a few seconds the red light comes on again. Also check to see if the system was locked released that. Tried...


Try flicking the transportation lock (on the left side under the scan lid) on and off. It has a picture of a pad lock shown locked and unlocked. Flip it back and forth and leave it in the unlocked position.

This worked for me. Good luck!

Oct 15, 2007 | Epson Stylus CX3200 All-In-One InkJet...

1 Answer

Scanner not responding to preview scan


Try this as a last ditch effort. Remove the software. Reboot the computer and come off line. Disable the Anti Virus program. Now install the soft ware. Then try. If the red light still flashes then assume it is new scanner time.

Jul 26, 2007 | Epson Expression 1640XL Flatbed Scanner

2 Answers

Error 5


I can't seem to find a error code 5. What software are you using to scan? Did the error start right after your first? Had the scanner been working?

Jul 12, 2007 | Kodak i40 Path-Through Scanner

Not finding what you are looking for?
Epson Stylus CX3200 All-In-One InkJet Printer Logo

516 people viewed this question

Ask a Question

Usually answered in minutes!

Top Epson Office Equipment & Supplies Experts

Alun Cox

Level 3 Expert

2678 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17130 Answers

Les Dickinson
Les Dickinson

Level 3 Expert

18425 Answers

Are you an Epson Office Equipment and Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...