Question about Thermador SMW272 Electric Double Oven

1 Answer

Burnt wire at spade connector

I removed element in lower oven due to failure to heat and found spade connector on element w/ no wire. can box be removed to access wire for repair or does whole unit need to come out of wall?

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Prodigy:

    An expert who has answered 500 questions.

  • Thermador Expert
  • 650 Answers

If you are unable to catch the wire through the front of the oven where the terminals go through then you will have to pull the oven from the wall and remove the rear panel. Of course make sure the power is off before attempting the repair.

Posted on Nov 20, 2013

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

kachbibi1
  • 979 Answers

SOURCE: Heating element on upper oven of a wall Thermador Oven

The control switch may be bad on it. If there are 2 elements on the top, they both are not bad at the same time.Check to see if the wires have not burned off the control switch first. Check to see if your breakers are O.K. Turn them both(maybe 3) off and then reset.

Posted on Jan 30, 2009

  • 1 Answer

SOURCE: I have a Thermador SC301 wall oven and the display

I have just repaired two SC301 ovens myself, but it is alot of work. You can get the oven's LED lights reconditioned at a company called CGI industries. Look them up on the web and click on the link for thermador. Removing the led panel and oven relay board is an involved job, but easier if you do it the correct way. First, turn off the power to the oven. Then pull the oven out of the wall socket about 1 quarter of the way. Remove the top cover of the oven with a phillips screw driver. This reveals the oven relay board. Take a digital picture of the board to remember the wire positions, or alternatively write them down. You also need to remove the touch panel (two screws underneath) and gain access to the LED. Remove the LED panel and wires. ship both to CGI (boards only) and you will have them back in less than a week. Costs about $170 before shipping. Reinstall and turn power on. All is good.

Posted on May 03, 2010

blackmar
  • 235 Answers

SOURCE: Lower heating element of oven

The element sparking and short circuiting has nothing to do with the cleanliness of the oven. An element will break down internally and short circuit due to it's age or hours of service. Have a look at the element to see if there are any holes/blow marks on it. If there are it requires replacement. Sometimes the element will look fine but will still be faulty.

Posted on Feb 27, 2011

ginko
  • 19396 Answers

SOURCE: Thermador Built in oven scd302 not heating upper

Hi.

Problem is usually either temperature probe or heating element.

Grab a multimeter and set it on impedance (Ohms).
Remove first temperature probe and then heating element.
If either probe or element is reading open (ohms infinity), then replace the part.

If both probe and elements are not open, then the problem is either wiring or oven electronic control. The most common fault resulting in no heat is the temperature sensor located inside the oven cavity.

Regards.

Ginko

Posted on May 31, 2011

  • 195 Answers

SOURCE: Thermador 30" wall oven.

Your touch in put key is stuck, replace ,power relay board and the touch panel

Always unplug the oven first before service

Posted on Dec 02, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Why won't the lower element heat?


DID U TEST THE NEW ELEMENT B4 TRYING IT? U MIGHT BE SURPRISE. OTHER WISE I WOULD D SAY CHECK THE WIRING AND CONNECTIONS IF ITS NOT WORKING, CHECK FOR VOLTAGE AT THE CONNECTORS?


1.Even a bad relay door switch will hinder your oven from operating.

If your oven has internal fuses, a wiring or component problem could have caused a fuse to blow. A blown fuse is an indication that a component has shorted or failed, and the problem will need to be corrected. Most ovens that use fuses will have an indication of the circuits that are affected by a particular fuse. If an oven fuse has blown, then you should inspect the oven element and the associated wiring to determine the cause before replacing the fuse.

THINGS TO CHECK:

the broil element
is the heating element that is found at the top of the oven and produces a very high heat for broiling. If the broil element isn't working, you should first do a visual inspection for signs that the element has blistered or separated. If the element appears normal then you can check for continuity with a multi-meter. Remove power from the appliance before performing this test. Remove the back panel and locate the terminals for the broil element and inspect the terminals and wires for signs of overheating or damage.

If there is no continuity then the element will need to be replaced. If the wires are damaged then they will need to be repaired. If the element is ok then you will need to check the broil circuit to determine the cause. This involves live voltage checks and should only be performed by qualified persons. Components to check include fuses, if the range is equipped, and oven control thermostat or electronic control. Depending on the manufacturer of the element, you will normally read between 19 ohms and 115 ohms


The bake element
is the heating element that is found at the bottom of the oven. Most electric ovens use both the bake element and the broil element in a bake cycle, with the bake element performing 90% of the heating. If the bake element isn't working, the oven may not heat. To help determine if the bake element is defective you should first do a visual check. If the element is blistered or separated then it should be replaced. If the element appears to look normal, then turn the oven on to a bake function for a minute and then turn it off.

Check the element for signs of heating and if it is still cold then it may be defective. Disconnect the power and then remove the back panel. First check the wires as they may have become loose or corroded. If the element appears to be fine visually, test it for continuity with a multi-meter. ( by placing the each of the meter prongs on each end of the heater element connectors) If the element is burned or no longer has continuity, it will need to be replaced. Depending on the manufacturer of the element, you will normally read between 19 ohms and 115 ohms



25760873-h2nezs2ipeosmtwvc0c05nbs-5-2.jpg

25760873-h2nezs2ipeosmtwvc0c05nbs-5-5.jpg

25760873-h2nezs2ipeosmtwvc0c05nbs-5-14.jpg

25760873-h2nezs2ipeosmtwvc0c05nbs-5-20.jpg

Jun 25, 2015 | Ovens

1 Answer

How do I change the lower element


there is usually two screws and one center bolt secures an element
and it will have two spade connectors to remove also
sometimes you need to remove the back
but more and more its done from inside the oven

Dec 04, 2014 | Ovens

1 Answer

Oven will not heat


the bake element has failed. they can be had for around 20 dollars. Unplug unit before
replacing the element. Usually will only need 1/4 inch nut driver to remove two
screws inside oven and slide out element and unplug the spade connectors.
The model and serial should be located behind the lower drawer on the left side.
An appliance parts store should carry this in stock since many models utilize the
same element. Hope this helps.

Sep 25, 2011 | Whirlpool 30" Self-Cleaning Freestanding...

1 Answer

Maytag electric oven model cwe5800acb. The lower element in the upper oven will not heat up. Can the lower element be replaced without removing the oven from the wall.


Yes, replace the lower element by first turning off the circuit breaker to the oven (110V is still to half of the 220V element circuit even though the oven setting is turned off), then unscrew the two screws holding the element to the back wall of the oven, then pull the element out (may have to tug it a bit to get the connectors through the insulation), and pull the wire connector clips off the element.

Mar 14, 2011 | Maytag CWE5800A Electric Double Oven

1 Answer

How do i replace the heating element in a diplomat aca3200 oven?


make sure the oven is switched off.remove all trays etc from oven,remove 2 posidrive screws from bottom of fan plate,remove fan plate,the element is around the fan,remove 2 posi screws from where the element goes through the side of oven and the one screw that holds the top of the element to the back of the oven.slowly pull the element out and remove the 2 poz and neg spade connectors.refit as removed.

Dec 30, 2010 | Ovens

1 Answer

I have a Elba Excelence cooker Px906. the lower heating element doesn't work. And the oven doesn't have enough heat. Is the element burnt out? If the answer is yes how can I replace it?


4 elements, 2 top , 1 back, 1 bottom. remove covers in oven to see rear and bottom if they heat.
possibly selector switch fault.
mine looks wired wrong from factory, cant for life of me see how it can heat as display indicates ???????????????????

Oct 19, 2010 | Ovens

3 Answers

I have a Jenn Air W131 model wall oven and I believe the lower heating element needs to be replaced. I will set the temp at 350 and it doesn't heat up at all. Is my assumption right that that is what...


If this is the problem no it isn't hard at all. Should be able to change right thru the oven without pulling out of wall. Make sure power off while doing this tho. But ist make sure broil does work.

Feb 01, 2010 | Jenn-Air JJW8330D Electric Single Oven

1 Answer

I used the cleaning feature on my kitchen aid architect series oven KEBK101 - now when you turn the oven on it does not heat up - what part do I need to replace - Kitchenaid will not address


Yup Thermofuse stops the elements from heating after the self-cleaning cycle. You have to take out the oven, TURN OFF THE POWER at your circuit breaker, remove all the screws on the oven back panel, you'll see the thermofuse near the center (there are two 1/4" spade connectors (one leads from one leg of the power junction box). Two screws to remove it.

Oct 27, 2009 | KitchenAid KEBC107 Electric Single Oven

1 Answer

My electric oven wont heat up


check the breaker box first, turn breaker off then on. then try oven again

check the timer, sometimes the timer gets set to delay and oven won't work

second, with oven off trace entire element with finger to see if there are any burnt spots.

if no burnt spots found, there may be a burnt wire leading to element in the wall behind

please, don't forget to rate my solution.

thanks

Jun 22, 2009 | Ovens

3 Answers

Oven won't heat.


EUREKA! I found the reset button and my oven is heating as we speak. Ok, open the oven door. there is a thin panel with vents right at the door latch. Unscrew the (6) screws and pull off the panel. There is a red button on the left back behind the wiring. GOOD LUCK!

Dec 08, 2008 | Dacor ECS130 Epicure Electric Single Oven

Not finding what you are looking for?
Thermador SMW272 Electric Double Oven Logo

1,138 people viewed this question

Ask a Question

Usually answered in minutes!

Top Thermador Ovens Experts

Dan Webster
Dan Webster

Level 3 Expert

8220 Answers

 Fix Your Board
Fix Your Board

Level 3 Expert

310 Answers

yadayada
yadayada

Level 3 Expert

75797 Answers

Are you a Thermador Oven Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...