Question about Audio Players & Recorders

1 Answer

Stereo stuck in protect mode - Audio Players & Recorders

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that has over 10 points.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 16 Answers

Unplug it wait a couple minutes plug it back in

Posted on Dec 09, 2013

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do i take my Kenwood car stereo out of protect mode ?


There may be an internal short which will have to be repaired before the radio can be used.

May 25, 2016 | Kenwood Car Audio & Video

1 Answer

Stuck in standby mode on Fisher RS-911A receiver


Does it power up or straight to standby? If it is on but in standby it could be speaker protection issues...check speaker wires and/or speakers for issues. If it's straight to standby and no power, it's repair shop time.

Jan 02, 2014 | Fisher Audio Players & Recorders

1 Answer

My jvc stereo is stuck on protected and it won't change the radio station off protected


Radios that are in "protected" mode often indicate a short in a speaker wire or a really bad speaker. Disconnect all eight speaker wires: white, white/black, gray, gray/black, green, green-black, violet, and violet/black. Turn on the radio and see if it still shows "protected". If it does, the radio is defective. If not, connect each pair of speakers back one at a time and see if it goes into protected mode. The one that causes it is the bad wire/speaker.

Dec 22, 2013 | Car Audio & Video

2 Answers

JVC KD-R610 is stuck in Protect mode


Try disconnecting your battery, reconnecting it, and resetting your stereo. If that doesn't work, the constant power (yellow wire) or ignition wire (red wire) may have come in contact with ground or isn't properly connected. Make sure everything is connected properly and try resetting your stereo. If it is still flashing "protect", the unit needs servicing Contact JVC Customer Care Center at: 800-252-5722.

Jul 22, 2010 | JVC AM FM CD DET FACE CAR STEREO

3 Answers

Kenwood car stereo cd player reads protect mode how do i fix this


i have a kenwood kdc-241 car stereo and it has gone onto protect mode i have done everything it says in the manual and even taken it out of the car just in case it was damp i have tried putting it back in but still is in protect mode can anyone help me please

May 25, 2009 | Kenwood Car Audio & Video

2 Answers

My sharp Stereo is stuck in '' protect'' mode


Protect mode is not something that a reset will fix. Basically it indicates that there is a problem with the final output stage of the amplifier. Normally this indicates that the output transistors are defective. In most boomboxes, the amplifier is a single IC. If you can post the model number, I can provide you with the required part and cost.

Thanks,
Dan

Mar 25, 2009 | Sharp Audio Players & Recorders

2 Answers

My kenwood car stereo says protect how do i fix this


well that means you had a safety stereo in the beggining and you proly didnt put the safety code in so it went into secure mode it to prevent the device from working if stollen

Mar 08, 2009 | Car Audio & Video

6 Answers

Security Code for Protect mode


Turn on the car so the radio is flashing "Protect." Look on the front / removable face of the stereo. On it you will find a small round hole - that's a reset button. Find a small paper clip, unfold the clip and stick it gently into the hole. The "Protect" will stop flashing, and Kenwood will be displayed. Unfortunately all your settings/presets will be gone, but at least the stereo is working again!

Apr 30, 2008 | Kenwood KDC-W3534A CD Player

Not finding what you are looking for?
Audio Players & Recorders Logo

Related Topics:

32 people viewed this question

Ask a Question

Usually answered in minutes!

Top Audio Players & Recorders Experts

kakima

Level 3 Expert

102366 Answers

 Grubhead
Grubhead

Level 3 Expert

5151 Answers

The Knight
The Knight

Level 3 Expert

74379 Answers

Are you an Audio Player and Recorder Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...