Question about JCPenney Gyropter RC Helicopter

1 Answer

Brand new and right out of the box, the bottom blades do not spin at all.

Any ideaa on how to fix it?

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    MVP:

    An expert that got 5 achievements.

    Habit-Forming:

    Visited the website for 3 consecutive days.

    New Friend:

    An expert that has 1 follower.

  • Contributor
  • 32 Answers

The Jcpenney ones seem to have the most problem with this. Some of the gears might be out together wrong, see if Jcpenney will take it back.

Chaio!

Posted on Dec 07, 2013

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

We have a brand new skyrover navigator YW85816 the bottom blades will not spin, nothing is stuck, you can spin them, but when you give it speed, it will not take off, because they do not go. HELP, 7 yr...


Hi! On all of thses tiny co-axil helicopters, it is common for either the tiny gear on a motor shaft, or the larger gear on the rod for the main blade to slide a bit so that the two gears no longer line up. You may need to open the helicopter by removing the side screws holding the two halvs of the body together. Check and see if the gear on the motor is meshing with the gear for the bottom blades. If not, you should be able to slide the gear on the motor shaft up or down until they mesh well. Hope this helps! Now, if somone can just tell me where I can order spare blades for this little copter!

Jan 10, 2015 | Washing Machines

1 Answer

S107G upper blade doesnt rotate,and leans to the side. lower blade spins...but no take off. brand new out the box......sup?


Hi,

Check that the bottom gear/cog is engaging with the motor drive gear. This is a common fault and usually just need to move the cog on the motor.

Kind regards, Julian

rccontrolfreak.co.uk

Oct 25, 2013 | SYMA Toys industrial New Syma S107 Mini...

1 Answer

Blade comes off wheel on horizontal saw have a wilton 7040 horizontal saw. after cutting about 1/2 thrru a piece of metal the blade sticks and then stars comming off the right wheel and starts cutting into...


if its a new blade, make sure that it is the proper length for the saw, sometimes aftermarket blades look like they are the right size but the difference of a few mm can cause the blade to track. if its an old blade, it could just be dull enough that it is binding on the material you are cutting and this draws the blade off the wheels. even if the blade isnt that old or seems sharp, if you have a brand new blade handy that would be the easiest thing to try.

your manual will have instructions on how to adjust the blade guide bearings. if this is a new saw, it SHOULD be set properly and be working from the factory but they may still need to be adjusted. an older saw obviously may have shifted a bit from normal usage. if you dont have a manual one can be downloaded from the wilton tools website.

before adjusting the guides, though, check to see that the bearings spin freely. if they do not spin smoothly with minimum pressure, they need to be replaced. they also should be replaced if they spin VERY freely because this is also an indication that they are pretty worn and may actually be binding up under pressure.

Dec 02, 2009 | Wilton Saws

1 Answer

I have an apache 3 channel helicopter.the top blades no longer spin so the helicopter just spins clockwise very quickly


Same problem I had. There are two motors. One to spin the top blade and a second to spin the bottom. My motor was defective out of the box to spin the top blade. Very poor quality as my AH 64 had a bad circuit board. I had to take parts from one to fix the other.

Sep 04, 2009 | Apache RC Mini Helicopter AH-64

1 Answer

The rotor on the base for the food processor will not engage. It spins freely, and the black wheel on the bottom rotates, but does not engage the blade spindle. Why?


Usuallt, it is simple - you have the position the gear box of the food processor side until there is no gap between the gear box and the teeth on the base - this usually takes me a few tries to get it right.

If you are confident that there is no gap, call Cuisinart and see about getting a new gear box - 1-800-726-0190

Aug 16, 2009 | Cuisinart BFP-703 Blender

Not finding what you are looking for?
JCPenney Gyropter RC Helicopter Logo

Related Topics:

125 people viewed this question

Ask a Question

Usually answered in minutes!

Top JCPenney Toys Experts

yadayada
yadayada

Level 3 Expert

79077 Answers

Andrew Taylor
Andrew Taylor

Level 3 Expert

19654 Answers

ray gallant

Level 3 Expert

51186 Answers

Are you a JCPenney Toy Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...