Question about Masterbuilt 20010306 Deep Fryer

1 Answer

Charmglow holder shell - Masterbuilt 20010306 Deep Fryer

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Masterbuilt Expert
  • 683 Answers

Hi there.
You may visit the Product Support of Masterbuilt at www.masterbuilt.com for your parts needed.
Regards.

Posted on Nov 22, 2013

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Location of brushes on dremel multi max kit


There should be a second brush. Look along the motor - you're looking for a spot where the armature (the part that rotates) is surrounded by a ring of little straight copper-colored bars. That's the "commutator" section. The brushes run against the copper bars.

Look on the outside of the plastic shell - there may be two large plastic screws, one on the outside of each shell half, right about where the commutator would be on the inside. Those are your brush holder screws; you should be able to change the brushes from OUTSIDE the tool without opening it. Some tools are built without external brush holders like that, but most have external brush holders.

If you find external brush holder screws, then track down the second brush and set it aside. It MAY be hanging from the brush holder in one of the shell halves. Unscrew both brush holders and remove them from the shell. Set them aside and reassemble the motor back into the shell. If the brushes are really short, like if they're nearly cube-shaped, then it's time to replace them. If not, try them again.

Insert one brush into each of the holes the brush holder screws came out of, and put the brush holder screws back in. Be careful not to cross-thread them. Try the tool.

If it still won't run, it's possible that an armature winding has given up the ghost and it's time to replace the tool...

Jul 11, 2014 | Dremel Multi Max Kit

1 Answer

Charmglow electric fireplace - fake flame does not work - serial #21704 DR 1839


If you are not getting any flame effects or the glowing ember bed, the bulbs (60 watt, small base chandelier) may be burner out.

To replace them, remove the plexiglass front and then the logs. The plastic glowing ember bed just lifts out, exposing the bulbs. Before replacing them, check to make sure they are not just loose in the holders.

Hope this helps you and thanks for choosing FixYa.

Sep 11, 2011 | Heating & Cooling

1 Answer

How do i remove the ignitors out of a charmglow grill model number 720 0036 HD 05?


The ignitor electrode(s) are held in place my a small tab that's attached next to each main burner with a small screw. To totally remove the ignitor electrode, disconnect the wire to it first, by pulling the wire's sleeve off the ignitor pin. Then unscrew the holder/tab. There should be no need to replace the wires, if you are just replacing the ignitor electrodes. Be sure to remove the battery from the Ignitor Module, before trying to remove the electrodes.

Apr 10, 2011 | Brinkmann Charmglow Stainless Steel LP...

1 Answer

I need a users manual for Charmglow 5 burner gas BBQ


Unfortunately, you listed 2 different Brinkmann Charmglow Grills, so I don't know which one you need the manual for. In any event, go to the link below and enter the correct model number for your grill and you can download the Owners Manual.

http://www.brinkmann.net/my_grill.aspx

Hope this helps to get you started.

Mar 07, 2011 | Brinkmann Charmglow Stainless Steel LP...

1 Answer

How does one replace charmglow burner tubes on my


most of it yes to get too, the parts you wish to replace

Jun 14, 2010 | Brinkmann Charmglow 810-7400-S Propane...

2 Answers

Charmglow 810-7400-S Propane Grill: have a charmglow patio heater, the pilot comes on ...


I have a Charmglow Patio Heater Model SRPH02, it needed a Thermocouple and searching the net was hard to find an ariginal part, but here it is, call 1-866-814-0585 $3.95 +6.00 shipping the original part.

May 16, 2010 | Brinkmann Charmglow 810-7400-S Propane...

1 Answer

Searching for an owners manual for my grill


In my online research, I was not able to find any free downloads for manuals of this brand. I did find a website that sold Charmglow manuals, though they did not list your specific model. However, they have a toll free # you can call and request your specific model manual. Hope this helps.

http://www.appliancefactoryparts.com/gasgrillparts/brands/charmglow/charmglow-manuals.html

May 16, 2010 | Home Decorators Collection Charmglow...

1 Answer

Charmglow electric fireplace bad remote control


Here is the home site for Charmglow - you could try to call them and see what they say. I would hope they want to keep their customers:

Charmglow Products 3701 Charlotte St, Pittsburgh, PA 15201-3201 (412) 683-6434 .aBtnGetDir { display:inline-block; width:107px; height:22px; text-decoration:none; vertical-align:bottom; cursor:pointer; } .aBtnGetDirLeft { float:left; height:22px; width:92px; overflow:hidden; font-size:0.85em; background:transparent url('http://sp.ask.com/sh/i/a11/shared_sprite_06.png') no-repeat -99px -401px; color:white; font-weight:bold; text-align:right; vertical-align:middle; line-height:22px; } .aBtnGetDirRight { float:left; height:22px; width:15px; overflow:hidden; background:transparent url('http://sp.ask.com/sh/i/a11/shared_sprite_06.png') no-repeat -301px -401px; }

Dec 12, 2009 | Kitchen Appliances - Others

1 Answer

3 burner charmglow gas gril


I am replacing burners and I need to know if the burners if they go tightened or loose.

Oct 20, 2009 | Brinkmann Charmglow Stainless Steel LP...

1 Answer

Need to find download for manual


I need more info, because I don't have the model #, but try here

http://www.appliancefactoryparts.com/gasgrillparts/brands/charmglow/charmglow-manuals.html

May 11, 2009 | Home Decorators Collection Charmglow...

Not finding what you are looking for?
Masterbuilt 20010306 Deep Fryer Logo

Related Topics:

43 people viewed this question

Ask a Question

Usually answered in minutes!

Top Masterbuilt Kitchen Appliances - Others Experts

Richard Lilja
Richard Lilja

Level 3 Expert

381 Answers

Angel Joseph Jr.
Angel Joseph Jr.

Level 2 Expert

683 Answers

Sock Puppet

Level 3 Expert

245 Answers

Are you a Masterbuilt Kitchen Appliances - Other Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...