Question about Printers & Copiers

2 Answers

Error code U8-6 on Xerox 5320 copier

When I push copy button the display reads error code U8-6 and paper jams just out of tray.

Posted by on

2 Answers

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert who has answered 20 questions.


    An expert that has over 10 points.


    An expert whose answer got voted for 2 times.

  • Expert
  • 163 Answers
Re: Error code U8-6 on Xerox 5320 copier

Dear sir please check the exposure lamp unit may be it is dusty so clean it or check exposure lamp circuit fuse etc....

Posted on Oct 07, 2007

  • Level 1:

    An expert who has achieved level 1.


    An expert that got 5 achievements.


    An expert whose answer got voted for 20 times.


    An expert who has written 20 answers of more than 400 characters.

  • Contributor
  • 53 Answers
Re: Error code U8-6 on Xerox 5320 copier

U8-6 suggests low or No light being picked up by the ccd.Does the Scan lamp come on at all?
Yes.?..clean mirrors and underside of platen glass (there is a white reference strip which must be clean
N?.lamp failure or reset the thermostat push button on lamp carriage (disconnect power, this can bite!)

Posted on Nov 16, 2007

Add Your Answer

0 characters

Uploading: 0%


Complete. Click "Add" to insert your video. Add


3 Points

Related Questions:

1 Answer

What does Fault code 078-211 mean on Xerox copier D110?

Found in the Administrator's Guide:

078-210 / 078-211
[Cause] Tray 6 (HCF) malfunction
[Remedy] Contact our Customer Support Center

Before calling, check for paper jam or small pieces of paper in and around Tray 6. There may be a piece jammed around a sensor that is throwing the error,

Mar 17, 2015 | Xerox Printers & Copiers

1 Answer

Xerox workcentre 5020/Dn c1 error

i have one xerox 5020 machine, there is display showing C1 error code in first tray and C3 error code in bypass tray .if open and close the machine will be idle and ready to cpoy. there is no paper pick up in both trays. please help to resolve the problem.

Dec 17, 2012 | Printers & Copiers

2 Answers


What this light sequence means that the printer has a paper jam.

When a paper jam occurs, the printer stops and the operator panel's Paper Jam light and Continue button lights come on. Press and release Continue twice quickly to display the specific secondary error paper jam light sequence.

How to clear Paper Jam

Press Continue button twice quickly to see the secondary error code.

To get the secondary error codes

When the Error light (!) and Continue button lights are both on, a secondary error has occurred.

When the Paper Jam light (4th light) and Continue button lights are both on, a paper jam secondary error has occurred.

Press and release Continue button twice quickly to display the secondary error code light sequence.

Press Continue button to resume printing once all the jammed pages are cleared from the paper path.

We recommend that you clear the entire paper path when a paper jam occurs.

To clear a paper jam:

1 If you are feeding paper from a tray, remove the tray, and then remove any jams.

2 Open the front cover and remove the print cartridge assembly.

NOTE: Do not leave the print cartridge assembly exposed to direct light for an Extended period of time. Extended light exposure can cause print quality problems.

3 Remove any jams in the area behind the print cartridge assembly.

4 Lift the flap at the front of the printer and remove any jams beneath the flap.

5 Open the rear exit and remove any jams.

6 After you have cleared the jams, reinstall the print cartridge assembly, make sure all printer covers and trays are closed, and then press Continue button to resume printing.

NOTE: The printer reprints the pages that caused the paper jam.

Jun 30, 2011 | Lexmark E232 Laser Printer

1 Answer

Printer Error message : Printer Error has occurred. 6000

Error 6000 gets displayed when there is a paper jam or other general malfunction. When the message "6000 Printer error has occurred. Turn off the printer then back on again. If the problem persists, see the manual." Is displayed, something may block the paper feed tray from opening.
If the printer is surrounded with documents or when you copy large documents such as books, make sure that you secure the clear space in front of the tray before printing / copying. When the error message above is displayed and if you find something is in front of the tray, remove it. Then, turn OFF the printer and back ON again and the printer will be ready for printing.
If you still have the trouble, contact the repair service.

Check the printer for any paper jam or try to reset the printer to release memory code errors.

1. Press and hold the Resume button for 1 - 2 minutes.
2. Open the cover.
3. Remove the cartridge and then reinstall it.
4. Close the cover.
5. Turn Off the printer.
6. Turn On the printer.

Dec 21, 2010 | Canon Printers & Copiers

4 Answers


Xerox 5225 keeps showing error 124-373 and cant one to enter into set-up or status mode.How to correct this error?.I have jobs to copy for urgent meeting soon.your email is needed

Aug 28, 2010 | Xerox Workcentre 5225 / Copier, With...

1 Answer

Have a HP Laserjet 2840..error reads "paper jam tray 1" there is no paper jam I can find. Help !!!

There are paper sensing switches above the paper tray. Most likely the actuator has fallen out .

Mar 30, 2010 | Xerox Phaser 6110 Laser Printer

2 Answers

I have xerox workcentre xd105f, can't make copies, paper jamed and letter P on display

to remedy the P display error remove the paper tray and take any paper from under the tray and between the rollers, clean the rollers with alcohol or an acetone solution to remove paper dust and paper debris, refit the paper tray with the paper pushed below the tabs on the tray ensuring that the correct paper size is shown, IE: ltr ltr-r etc.
power the unit off and on and you should be back in business.

If this remedies the problem please rate the solution accordingly



Jun 19, 2009 | Xerox WorkCentre XD105F Laser Printer

1 Answer

Xerox 5314 copier giving error code of u2

A U2 means the machine did not see the lamp scan. The lamp did not leave the right side of the machine. May be hung up on something, may have broken a cable the scan motor may be bad, I would first of all remove the glass and see if there is anything binding the lamp and keeping it from scanning. If you think it feels tight to move, that is normal on a 5314. What I am looking for is the lamp stopping not being able to move.

Mar 14, 2009 | Xerox Printers & Copiers

Not finding what you are looking for?
Printers & Copiers Logo

Related Topics:

252 people viewed this question

Ask a Question

Usually answered in minutes!

Top Printers & Copiers Experts


Level 3 Expert

94113 Answers

old marine
old marine

Level 3 Expert

1313 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17129 Answers

Are you a Printer and Copier Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides