Question about Initial HDTV-322 32 in. LCD Television

1 Answer

Tv wont stay on

The power and standby button work, but when I press power the screen lights up for a second and the words "composite" flash on the screen. unfortanatly I do not have a manual or remote control.

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 2 Answers
Re: tv wont stay on - Initial HDTV-322 32 in. LCD Television Flat Panel Televisions

Press the source button after it comes on

Posted on Apr 09, 2008

Add Your Answer

0 characters

Uploading: 0%


Complete. Click "Add" to insert your video. Add


3 Points

Related Questions:

1 Answer

Emerson TV not working

The capacitors on power board must be changed oth

Aug 02, 2016 | Emerson LC320EM9 32 in. LCD HDTV

6 Answers

55hds69 hitachi plasma

I have had some issues with high ESR readings in the capacitors in the scaler circuits in those units. Do you have an ESR meter to check the caps in circuit?

May 14, 2008 | Hitachi 55HDS69 55 in. Plasma Television

1 Answer

Bush tv 3 weeks old, tried turn it on but just a black screen,standby light turns blue as if it's on also if I press any buttons on it the blue light flashes like working but just a black screen

Here goes:

#Press and hold the on/ off button...
#Whilst holding unplug the plug from the wall...
#Continue holding for 30 seconds...
#Plug in the plug whilst continuing to hold the on/ off button...
#Continue to hold for a further 30 seconds...

And the screen should come back on!

Jul 23, 2016 | Bush Flat Panel Televisions

1 Answer

Tv is stuck on standby. The standby light (red) is steady and when I press the STANDBY button, nothing happens. no response or flashing light.

If your LCD TV or monitor has stopped working, or is displaying one of the following symptoms, then it's a candidate for some new capacitors
- Flickering screen
- Screen image disappears after several seconds
- Dim screen
- Slow start
- Power LED on, but no picture
- Unusual colors and/or lines
The primary cause of LCD TV and monitor failure is caused by faulty capacitors. You can examine the capacitors in your LCD TV or monitor and actually see if they are bad.
If they appear bulged on top, then they need to be replaced.
New capacitors will solve a host of problems in LCD monitors and TV's and will extend the life of your monitor or TV by several years.
Check the cables, connectors and connections.
Take it to a repair shop.
LCD TV Repair No Power Power Supply Common Symptoms Solutions How to...

May 11, 2015 | Flat Panel Televisions

3 Answers

Funai TV will not stay on. It turns on for 1 second and then turns off. Red standby light blinks on and of, what can I do?

Either the power driver board is faulty, or it has a humidity sensor in it, which turns it off. Move it to a very dry place for a few days, then try it again and it might work.

Jan 19, 2015 | Funai Flat Panel Televisions

1 Answer

My sony kdl-46v3000 standby light blinks 5 times tv wont turn on

The TV enters standby mode when there is no signal for 30 seconds.
I searched standby using Ctrl+F and found this information. It seems you should be able to bring it out of standby using the power button on the remote. You want to make sure there is an input connected and if it is connected to a PC that the PC isn't telling the TV to go into standby.
Try pressing the input button and changing inputs once you press the power button and the Standby is flashing.
If this doesn't work you may need to contact Sony Support.

Apr 10, 2014 | Sony Bravia V-Series KDL-46V 46 in. LCD...

1 Answer

How to determine if power board on emerson tv model lc320em1 is shot

The power supply regulator board to your TV is now working fine, and has no problems at all, as, there is standby light. Check all the other voltages comes out from the power board, to main board. If all of it found OK, the fault should be at its main board.
About blinking of standby/power light;
These blinks (flashes) are fault indication. By the number of blinks occur at one time switch ON, you can get an idea about the faulty circuit stage inside the TV. Count the blinks occur at one time switch ON, carefully. Do it once again, and make sure about the number of blinks. If the flashes are continious, non-stop, the main system control IC should be suspected. If you wish to get more details, check the site linked here. It has blinking codes detail to many brand TVs. Pull up older posts. Check the site in 'Mosaic' view. It will make search easy.

Jan 19, 2014 | Emerson Lc320em1 TV

1 Answer

PDP-4340HD keeps turning off.

Continuous blinks of standby light indicates a fault in the IIC data bus. The main board is likely to be faulty. If you wish to know more Check this link.

Feb 03, 2013 | Pioneer PureVision PDP-4340HD 43 in....

Not finding what you are looking for?
Initial HDTV-322 32 in. LCD Television Logo

Related Topics:

85 people viewed this question

Ask a Question

Usually answered in minutes!

Top Initial Flat Panel Televisions Experts

Starnley Johnwells
Starnley Johnwells

Level 3 Expert

1029 Answers

Cindy Wells

Level 3 Expert

4718 Answers

The Knight
The Knight

Level 3 Expert

66330 Answers

Are you an Initial Flat Panel Television Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides