Question about Samsung HL-S5087W DLP TV

1 Answer

Samsung DLP HL-P5063W. . .no lamp!

I have a 50" Samsung HL-P5063W (2 1/2 yrs old) which does not power on. . ."Lamp" light flashes for 20 seconds and then you hear PS clicking, repeats cycle 3 times before it shuts off and all 3 lamps flash! Samsung Tech told me to replace lamp. . .they transfered me to local auth. service who told me same and sold me lamp. . .to no avail, then Samsung told me it had to be balast. . .local auth. service guy told me same, sold me balast, replaced it. . .to no avail! So $300 later. . .same symptoms. . .same problem! Local Samsung guy, who also told me, and sold me lamp and balast, wants $75 now to diagnose? I'm alittle upset with Samsung and their local service guy! Any ideas? Thanks, Matt mdurrin@msn.com Samsung model HL-S5087W 50" dlp . Lost picture ,then sound. Three flashing lights on console. Contacted Samsung,said replase lamp. Did so with same results. Contacted Samsung ,said probably ballast. Replaced ballast with same result.

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Genius:

    An expert who has answered 1,000 questions.

  • Samsung Master
  • 1,039 Answers

Remove the rear cover and check the lamp cover switch. Earlier versions used a black plastic switch holder that may break due to improper assembly. The part number for the holder is BP61-01240A. Newer versions use a metal tab attached to the engine. In this case, improper assembly may cause the lamp cover switch to be extended past its range, either breaking the switch or causing it to have an open contact. Replace the switch with BP91-01231A.

Note that in these models, when reinstalling the rear cover, it is best to remove the lamp cover first, install the rear cover, then install the lamp cover. This will make sure that the lamp switch is properly engaged.

Posted on May 02, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

HL-P5063W Turns on, but no picture.


remove and inspect the lamp the model indicated uses---you can usually also look from the rear to see if lamp comes on at all---set also prone to bad color wheel--grinding or high pitched fan like sound--it faces the lamp--with lamp removed look to see it is not shattered or missing pieces and that lamp not shattered inside.
10_22_2012_4_53_15_pm.jpgtypical color wheel

Oct 22, 2012 | Samsung HL-P5063W 50" Rear Projection HDTV

1 Answer

My televison keeps randomly turning off. It simply turns off for no reason. Is this the begining of something major? Please let me know -Samsung HL-p5063w


Hi,do you hear any strange noises? If you hear clicking or like wanting to turn on it could be the board that powers the lamp it's called the ballast.Here's the instructions to replace it :http://www.fixyourdlp.com/guides/samsung/bp47-00033a.php But if you don't hear any strange noises,tv is around 6000 hrs,2-4 yrs it could be time to replace the lamp.The lamp you need is BP9600224B.Have a blessed one!

Mar 24, 2010 | Samsung HL-P5063W 50" Rear Projection HDTV

1 Answer

Samsung 50" DLP No picture and very deep & lound vibrating sound. Red lights flashing,Sand By Temp. And Green lights flash Lamp.


Loud sound you are hearing is coming from your color wheel and has your Lamp ever been replaced? this set has 3 Fans they all must be running for set to operate correctly! Encompass Parts has Boards and Color Wheel But for Lamps Mats has them for 99.00 1-800-628-1118 and EC Parts 1-800-638-3328

Jan 21, 2010 | Samsung HL-P5063W 50" Rear Projection HDTV

1 Answer

Tv turns off after watching an hour - then proceeds to turn off every 15 to 20 minutes there after


Hi if your tv is a DLP or LCD and you hear clicking or like wanting to turn on ,most likely its an issue with the ballast which is the board that powers the lamp.(Discard if tv is )If you hear buzzing or spinning noises it could be you color wheel.Also check if fans are running ok or if they are dusty, clean them with an air pressure can if they are dirty.It could also be time to replace the lamp.they normally last 6000-8000 hrs if it's a Philips brand if it's na Osram lamp they will last 4000-5000 hrs 1-2 yrs.God bless you!

Oct 05, 2009 | Samsung HL-P5063W 50" Rear Projection HDTV

1 Answer

I just replaced the lamp on my samsung HL-P5063W (DLP TV)...now the TV will not turn on (no picture...but I do get sound)...when I plug it in, it automatically starts to power on...then it starts making...


Sounds like a bad color wheel. Generally when the color wheel goes bad, when you try and turn the TV on the lamp will ignite for a couple seconds and then turn off. It also makes a rather high pitch squealing noise.

www.Partstore.com should carry a replacement color wheel for your TV

Sep 07, 2009 | Samsung HL-P5063W 50" Rear Projection HDTV

1 Answer

No picture after replacing color wheel


every time I see this itbis a cable or plug that was left out or one that got pulled on and pulled the connector up out of the plug a little, you need, and not by sight by your hands to go over every plug and connector till you find one.
Larry Dillon

Aug 01, 2009 | Samsung HL-P5063W 50" Rear Projection HDTV

2 Answers

Samsung 50" DLP - Lamp Light Blinking after bulb replacement


Listen closely. The tv should make a high pitch whine as it turns on. If it does wait and see if it tries this a few times. If yes then check the bulb, I have seen cases where the lamp shoves the power connector back into the set. If the tv starts with a grown or heavy vibration noise, then your color wheel may have broken and needs replaced.

Jul 11, 2009 | Samsung HL-P5063W 50" Rear Projection HDTV

1 Answer

Hlp5063w 50'' projected samsung lamp won't come back on ?


It could be the lamp but don't overlook the lamp door interlock switch. If the lamp door is not aligned properly, you may have intermittent shutdown or no start conditions. You can temporarily cross the interlock switch to confirm that this is the cause.

michtech

Feb 17, 2009 | Samsung HL-P5063W 50" Rear Projection HDTV

2 Answers

Samsung DLP HL-P5063W


you have the same problem I have. The problem is fixed by changing the new light bulb. The problem appears again after 1500 hours of use. You can keep buying new light bulbs or avoid it by not buying another Samsung TV.

Sep 23, 2007 | Samsung DLP HL-P4663W 46" Rear Projection...

3 Answers

Samsung DLP HL-P5063W. . .no lamp!


You will need to have it diagnosed if you do not have the service manual, or the knowledge of how these circuits work. I can tell you to replace this or that but it would be a guess! You need to start measuring the voltages on the ballast circuit, as I have seen door switches, fan sensors, heat sensors cause all of your symptoms as well. Good Luck

Jul 24, 2007 | Samsung DLP HL-P4663W 46" Rear Projection...

Not finding what you are looking for?
Samsung HL-S5087W DLP TV Logo

788 people viewed this question

Ask a Question

Usually answered in minutes!

Top Samsung Televison & Video Experts

The Knight
The Knight

Level 3 Expert

76046 Answers

Jerry Greenberg
Jerry Greenberg

Level 3 Expert

1691 Answers

Demonic-2011
Demonic-2011

Level 3 Expert

512 Answers

Are you a Samsung Televison and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...