Question about Mitsubishi WS-55807 TV

1 Answer

Convergence problem my tv is experiencing a convergence problem, similar to the other convergence problems posted to this site. i live in rural montana and there isn't a tech for miles. do you have any suggestions or solutions? Any advice would be greatly appreciated. Thanks, Ipson

Posted by on


1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 790 Answers

Mostly defective convergence are subject to replace!

Posted on Oct 05, 2007


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Cycle selection will not work

I also live rural and repairmen drive many miles a day getting to people .

Oct 26, 2015 | Kenmore Washing Machines

1 Answer

Lots of Blue shadows off to side. concaved picture almost

HI, this is a failed convergence chip that is located on the convergence board. it will need to be replace ASAP. you can just replace the chip or , you can order a new board.

Replacing the chip can be a rough job if you don't have tech experience. if you are a fluid tech and you can solder and know your way around a circuit board, just replacing the chip will cost less. if you are not an experienced TV tech, i recommend a service call to the nearest TV tech to replace the convergence board.

May 20, 2009 | Sony KP-46WT510 46" Rear Projection HDTV

2 Answers

Toshiba 46H84 Blue CRT Misaligned

The problem is you convergence IC's. STK392-110. If you are not experienced I would contact a tech to do this work. Repair costs should be 200-400 depending where you live.

Dec 08, 2008 | Toshiba 46H84 46" Rear Projection...

2 Answers

Digital converter box

Greetings kathy76turne,

In February 2009 you will be unable to receive ANY analog television signals therefore the digital converter box will be a necessity to receive any over the air broadcasts.

I am unable to answer the question about the mini van's electrical capability, however you might find the following link handy to get more information.

Thank you!

Go Ahead. Use Us.

Jun 09, 2008 | Mitsubishi HD-6000 DTV Receiver / Video...

1 Answer

Sony KP-46WT510 46 in. ic problem

If you can solder it should be an easy fix for about 50.00 You need two Convergence ICs STK392-560 the link I am posting has replacement ICs and provide free tech support by instant messageing as well as instalation instructions with pics on how to change the ICs. A repair shop will charge between 4 and 6 hundred to do the job which is about an hour. I would also suggest getting about 6 of the 4.7ohm 1/2watt resistors also as sony will sometimes blow a couple with the ICs but the repair tech will help you find the open one if there are any. Heres the link to the site.

May 23, 2008 | Sony KP-46WT510 46" Rear Projection HDTV

1 Answer

Need help

Sounds like the convergence amp ICs need to be replaced. This is a common and easy repair. You need two STK392-110. You can get replacement ICs at the following link and they include free installation instructions with pictures and also free instant messageing with their repair tech on line while you do the repair.
Here's the link

Apr 15, 2008 | Televison & Video

1 Answer

RCA P52937SG Convergence

Convergence amp ic bad
Sony Convergence

Jan 29, 2008 | RCA P52937 52" Rear Projection Television

1 Answer

Picture convergence

There are 2 large convergence output IC's and one of them has burned out. The defective convergence IC should be replaced and the convergence circuits realigned by a qualified tech experienced in projection sets.

Sep 01, 2007 | Philips 60P8341 60" Rear Projection...

Not finding what you are looking for?
Mitsubishi WS-55807 TV Logo

Related Topics:

109 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mitsubishi Televison & Video Experts

matt martin
matt martin

Level 3 Expert

1244 Answers

The Knight
The Knight

Level 3 Expert

75970 Answers

Jaime Hernandez

Level 3 Expert

2337 Answers

Are you a Mitsubishi Televison and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides