Question about Washing Machines

2 Answers

Zanussi turbodry 1050

When the machine is switched onto to any wash cycle there is no filling of water, i have checked the water pipes - no problems. If i turn the selector then the machine goes into it's spin cycle but still no water. Also works in dry mode.

Posted by on

2 Answers

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Expert
  • 209 Answers
Re: Zanussi turbodry 1050

This may sound silly but check the waste outlet pump electrically, some models are wired up so if the pump fails the water will not enter the machine, this works on the theory that if it fills up it can not empty also check the solenoids for open circuit electrically, double check the water supply to the machine, it may have been fine but you could have kinked the pipe placing the machine back where it should go?

Posted on Oct 04, 2007

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer
Re: Zanussi turbodry 1050

Washing machine zanussi 1050, does washing properly, can not open the

Posted on Sep 06, 2009

Add Your Answer

0 characters

Uploading: 0%


Complete. Click "Add" to insert your video. Add


3 Points

Related Questions:

1 Answer

Zanussi turbodry wdt 1075 washing machine fills & drains but does not perform wash cycles or spin cycles drum does not rotate

Quite probably the motor brushes. Disconnect from mains. Tilt machine backwards as far as possible. On motor, disconnect wires to brushes. With a multimeter, check continuity between brush and any segment if the commutator. If open circuit, replacing the brushes should do the trick. Also visually examine the commutator for damage

Aug 17, 2014 | Zanussi Washing Machines

1 Answer

My washing machine keeps flashing e10 what is the problem

E10 - not filling make sure the water is turned fully on and pipes are not frozen if in garage. when you have checked everything then turn off machine at control panel and then unplug it for 5 mins then plug back in turn on and start cycle it should start to fill. hope this helped.

Dec 28, 2010 | Zanussi FJS1225W Front Load Washer

1 Answer

Zanussi 1050 washing machine will not fill with cold water . Cold water hose replaced because of a leak in old hose but machine will not now fill

Assuming water supply to machine is okay and no kinks in the hose Then its the solonoid valve that is faulty and needs replaced

Apr 01, 2010 | Washing Machines

1 Answer

It wont drain the water away after a wash we

sounds like your pump may be gone, or could be pipe blocked. to check pipe fill machine take outlet pipe at rear of machine and lay this into a bowl. If water flows ok then all pipes are clear. As water is coming through just put machine onto spin cycle and raise hose to see if water will then pump out.

Feb 17, 2010 | Zanussi FS1255S Front Load Washer

1 Answer

When switched on my washing machine doesnt fill with water

the obvious check that there is power to the machine

on normal wash cycle listern to see it you can hear a humming sound round about where the soap dispencer is, if not it could be a faulty electronic inlet valve , check to see if you have duel fill (ie hot and cold fill ) if you have try doing a cold water wash and see if you have the same problem if you have then check themostat, and then onto the more thechnical thing the programmer, the 1st couple of things you can check your self you will need an engineer to check the programmer and stat


Jan 16, 2010 | Zanussi FJ1254W Front Load Washer

1 Answer

What is E 40 on Zanussi Turbodry 1200?

E40 indicates the doors not closed properly. Sometimes it can be the lock itself or the main control board

Nov 24, 2008 | Zanussi FJS1225W Front Load Washer

1 Answer

Washer stuck

i am assuming that water comes in at the start of cycle and machine does not then progress. Points to a timer fault unfortunately. These timers are expensive and quite hard to fit. don't recommend repair in view of age of appliance.
honestly can't see how related to sock problem

Jun 26, 2008 | Washing Machines

1 Answer

Machine filling and then immediately draining

Hi You need to higher your outlet pipe on the back of the machine there is usually a clip to hold the pipe in place 3/4 of the way up the machine so it looks like a u upside down its should stop the machine from emptying straight away

Apr 29, 2008 | Zanussi ZWF1430W Front Load Washer

1 Answer

Zanussi IZ161S Water filling problem

Check the drainpump. It may be clogged with lint or something, or blocked.

Jan 14, 2008 | Zanussi IZ161S Front Load Washer

4 Answers

Zanussi jetsystem Turbodry 1200

It appears that you may have a faulty door interlock or a faulty PCB. pcb is not really a DIY job as some boards require proramming on certain versions. Regards Advisor

Oct 30, 2006 | Zanussi FJS1225W Front Load Washer

Not finding what you are looking for?
Washing Machines Logo

Related Topics:

507 people viewed this question

Ask a Question

Usually answered in minutes!

Top Washing Machines Experts

Dan Webster
Dan Webster

Level 3 Expert

8147 Answers

Richard Roth
Richard Roth

Level 3 Expert

9472 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17129 Answers

Are you a Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides