Question about Kenmore 44832 Front Load Washer

1 Answer

Kenmore Elite HE 3T front load washer

When spinning, washer stops and exhibits an "F 09" code. Washer is level and well-supported.

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 447 Answers
Re: Kenmore Elite HE 3T front load washer

Hope this helps ...... F09 is a Overflow Condition If the Overflow contact on the pressure switch is Closed for more than 60 seconds an Overflow condition will occur. In an Overflow condition, the Door will remain locked, and the Drain Pump will run constantly, even if PAUSE/CANCEL is pressed twice and the Display is cleared. Unplug the unit to service. Potential Causes ? Check the drain hose and make sure it is not plugged or kinked ? Check Wire Harness connections to the Drain Pump, Pressure Switch, and Central Control Unit (CCU) ? Check/ Clean Drain Pump Filter of foreign objects ? Check for Drain Pump Failure ? Check the Inlet Valve for proper shut off ? Check the Pressure switch for proper operation PLEASE rate my solution

Posted on Oct 04, 2007

Add Your Answer

0 characters

Uploading: 0%


Complete. Click "Add" to insert your video. Add


3 Points

Related Questions:

1 Answer

Keeps Stopping and saying UE

uE error code 79631512210 Kenmore Elite Washer - Sears ... > Ask an Expert
Jan 10, 2014 - uE error code 79631512210 Kenmore Elite Washer ' SearsPartsDirect. ... After unloading the washer completely, the machine attempts to rebalance the .... to ensure proper fit and to keep appliances running for years to come.

UE Error code on my front loading Kenmore washing machine > Manage My Life > Questions
Jun 13, 2011 - I have a Kenmore 3.5 cu. ft. front loading washing machine (model #4027) and it is 1 year old. ... what does the F35 error code on my kenmore elite front loading washing machine mean? F13 code on Kenmore Elite HE3 front loadingwashing machine.

Jan 21, 2016 | Kenmore Washing Machines

1 Answer

F-24 error code so I ran a clean washer cycle, and the laundry room is now flooded.

what's f24 code? - Kenmore Elite HE3 Washing Machine ...'s+f24+code

iFixitAug 21, 2015 - Aiman, The F24 error code indicates a water temperature sensor reading that is ... The Kenmore Elite HE3 is a washing machine by Kenmore.

F24 Error Code on My Kenmore Washer ' eHow > Home
F24 Error Code on My Kenmore Washer. Kenmore washing machines have several high-tech features, such as a stain treatment option, reduced energy and ...

Kenmore HE2 Plus Front Load Washer F24 error code ... > ... > HE2 > Kenmore HE2 Plus Front Load Washer
...error code F24 I have a Kenmore HE2T washer and I keep getting an F24 error on it.. I have no idea what is means can't find the manual help!!! The "F24" error ...

I have a Kenmore HE2T error code F24 - Fixya
Dec 9, 2009 - Posted on Dec 09, 2009.

Dec 06, 2015 | Kenmore HE2 Plus Front Load Washer

1 Answer

Washer makes knocking noise while in spin cycle. Shock absorbers have been replaced and are good and machine is level. Kenmore Elite H E 3T Model #44932

Check your front and rear counter-weights. They are made of concrete and start to chip away. More so the rear than the front. When you open it up look on the base and see if you have chips or chunks of concrete. I had that problem as well - also make sure you spray lube inside,check your "Spider" wheel, and belt.

Jul 12, 2010 | Kenmore 3.8 cu. ft. HE3t Front Load Washer

1 Answer

My Kenmore Elite 3t is banging in the spin cycle and the plastic ring behind the rubber boot is shredding. Any suggestions?

are you using a gel soap if not that may be your problem powder soaps cannot be used in front load machines it damagege the bearings in the back of the tub

Dec 17, 2009 | Kenmore Elite 45986 Front Load Washer

1 Answer

Kenmore elite 3t the front light to select wash blinks but when s

Press 'drain' & 'spin' together for 3 seconds to see if it clears. This is your control panel lock.
If not cleared unplug the washer & wait for 30 minutes for the CCU (computer) to reset.

If helped you can rate.

Mar 01, 2009 | Kenmore Elite 45986 Front Load Washer

1 Answer

F and then 06 error/ Kenmore elite HE 3T series 4

well i found the answer on browsing through fixya. the following would assist you with the needy.Hoe it is helpful.Pay back with your comments if the problem is solved.

Dec 14, 2008 | Kenmore Elite 45986 Front Load Washer

1 Answer

Kenmore elite HE 3t washer

F32 is the code for a Water Level Switch Failure.
1. Remove the top panel from the washer by removing the three screws in the top back of the washer.
2. Inside the back right corner is a round plastic box, fastened to the side with a plastic snap. In will have a wire connector and a small, rubber hose connected to it.
3. Check to make sure all the connector wires are connected and tight. Unplug washer for 30 seconds to reset it. If the cycle fails still with the F32 code, you'll need to replace the Water Level Switch.
4. If the Water Level Switch does not eliminate the F32 code, it then the machine controller may have failed.

Jul 04, 2008 | Kenmore Elite 45986 Front Load Washer

1 Answer

F 11 Error Code

The door will stay locked if the machine did not drain properly. Try running a Drain & Spin cycle.

Mar 17, 2008 | Kenmore Elite 45986 Front Load Washer

Not finding what you are looking for?
Kenmore 44832 Front Load Washer Logo

Related Topics:

203 people viewed this question

Ask a Question

Usually answered in minutes!

Top Kenmore Washing Machines Experts

Richard Roth
Richard Roth

Level 3 Expert

9472 Answers

Jesus  Colon
Jesus Colon

Level 1 Expert

12 Answers

Fred Sops

Level 2 Expert

271 Answers

Are you a Kenmore Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides