Question about Office Equipment & Supplies

2 Answers

Canon NP 6030 Error code E010

The copier turns on, starts warm up, then displays Error Code E010, please turn copier off then back on. Will not get past this error code.

Posted by on

Ad

2 Answers

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Chiudere sportello superiore destro

Posted on Oct 16, 2009

Ad

M/C GEARS JAMMED . MAY BE DP UNIT JAMMED OR MOTER (MAIN) JAMMED OR FULL OF DUST ETC.

Posted on Oct 06, 2007

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Canon ir 2018n error code e010


check the drive of the main motor >may be a broken gear .If that is ok then check the main motor in another machine.If that is also okie then u have got urself a fried DC controller PCB.Replace it

Mar 28, 2012 | Canon Office Equipment & Supplies

1 Answer

I have canon np 6650 it shown E010. i have try to reset, checking the fuse on the dryer paper please help me


if error E010 occure, it means your Main motor not running,
motor or motor drive board or mother board problem,
if show E010 after running the main motor, check motor driver board or mother board,
but 99.9% case of E010, cause of main motor problem so check the main motor first,

Aug 11, 2011 | Canon NP 6650II Copier

1 Answer

Error code e010


This is the code for the main motor. Something is making this motor work extra hard and not rotate as fast as it should. Take off the back cover and turn on the copier. See what direction the motor is turning. See if you can make it move by rotating the motor in the right direction. The fuser may be binding, the drum, or developer. You will have to isolate the problem. I've never had to replace a motor but yours could be a first. Good luck.

Mar 21, 2011 | Canon NP 6035 Copier

1 Answer

I have machine canon 6030 np and there problem called : E224 please send how can I solve it


Basicly, a E224 is a scanning lamp error code. Here's a question for you??? Will the scanning lamp turn "ON" at all? If so, then the problem is with the scanner power cable. If the lamp will not turn "ON" you may have a blown lamp & or thermal fuse on the scanner unit. You can not clear the code until the problem is fixed. Good Luck

Feb 16, 2011 | Canon NP 6035 Copier

1 Answer

Once the np 6050 is turned on it displays error code E010 switch off and on again


E010 code is main motor lock. Open front cover, Release Transport/Fixing Unit tray. Pull the tray out untill it stops. Try rotating the larger knob to see if Fixing unit will turn...if not, raise the exit/stripper assembly to check for jammed paper. If no paper present and the Unit turns freely, reinsert Transport/Fixing tray into copier. Latch into place. Close front cover. Power on machine.
It is possible that the main motor has failed, but not likely.

Jun 19, 2009 | Canon NP 6050 Copier

1 Answer

Once the np 6050 is turned on it displays error code E010 switch off and on again


E010 error code is a main motor lock .
Check for jammed paper in the Fixing unit.
Pull transport/Fixing Unit tray out and rotate large knob on left side to check Fixing unit for obstruction/turnability. Other than this, it could be main motor failure.....

Jun 08, 2009 | Canon NP 6050 Copier

3 Answers

Canon COpier NOP 6030 error code E064


hi.... sir
i've an erorr code for copier np 6030 is 064 how to solve it

Oct 28, 2008 | Canon Office Equipment & Supplies

1 Answer

Canon Copier NP 1020 - error code E0


pretty much the same, the codes are good for several models not just one.

you need to find the other numbers to know exactly which code it is, press the start or stop key to see it display the other #'s.

fuser is on the left side if you replace the parts might as well replace the claws and oil roller.

"E000" Heater lamp, Thermistor, DC controller "E001" Heater lamp, DC power supply / AC Driver circuit board, Thermistor, DC controller. "E010" Main motor clock sensor, DC controller PCB, Main motor, DC power supply / AC Driver circuit board

Sep 16, 2008 | Canon Office Equipment & Supplies

1 Answer

Canon 6650 E010 error


uhhhh, wow. That is a main motor lock error code. As in the main motor is bound up and cant move because of a physical bind or the motor has taken a dirt nap. Very rare code. I have been working on Canon machines for 20+ years and only seen that once. One of those what I call "DUMBO SIZE" paper clips truly kept the motor from turning. GFL.....

Jul 20, 2008 | Canon NP 6650II Copier

2 Answers

Canon np 6030


Is it looking for toner or is there still a jam in it. You may want to try to turn it off and unplug the sorter and turn it back on. If that dose not work turn off again and unplug the adf and turn it on again. If that dose not work if you have unplug the bottom 2 trays. If one of those is causing the problem look deeper in to one of those units. Also, will it showw or flash a error code on the display?

Mar 18, 2008 | Canon NP 6050 Copier

Not finding what you are looking for?
Office Equipment & Supplies Logo

Related Topics:

1,496 people viewed this question

Ask a Question

Usually answered in minutes!

Top Office Equipment & Supplies Experts

k24674

Level 3 Expert

8080 Answers

Cindy Wells

Level 3 Expert

5679 Answers

Marvin
Marvin

Level 3 Expert

83779 Answers

Are you an Office Equipment and Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...