Question about Audio Players & Recorders

1 Answer

Sansa mp3 player 2.0gb

My player will not turn on. i have tried everything. and no...its not on hold. the goodbye screen wont even turn off and the computer does not detect the device. not happy jan. and i think i may have picked a player and a brand that has lots of problems. the blue light still comes on but alas, nothing else. very frustrated as this is not the onli problem ive had with this player. can anyone help?

Posted by on

  • 7 more comments 
  • purdee Oct 03, 2007

    how do i do that if i cant even turn it on? and nothing happens when i connect it to the pc

  • purdee Oct 03, 2007

    it also wont charge at all. it turned on to the menu once, all the music that was in there is gone now and then then it saiid battery low and then it went off. and then that was it.

  • purdee Oct 03, 2007

    seriously. i im illiterate when it comes to this stuff. very close to just taking it back. i have no idea what a 'twister series' is?

  • purdee Oct 03, 2007

    so its like a usb stick thing? is there no other way? im in australia dude

  • purdee Oct 03, 2007

    excuse me but when i try to do something to my mp3 it freezes

  • Denia Netro Nov 19, 2007

    i was listening to music , then i turn it off but when i tried to use it again it didn't turn on. i tried to reset the device and nothing happend.i plugged it in my pc and it didn't turn on and there was no notice on the screen that adviced that the device was connected to the pc.

  • david saunders Nov 25, 2007

    i plug my sansa e200 series into the computer and it only turns it on it doesnt say connect like it is supposed to

  • Anonymous Dec 28, 2007

    it freezes

  • Anonymous Jan 05, 2009

    Player will not turn on.

×

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 790 Answers

Your MP3 is have Virus Doomboot Virus! reformat your MP3 to software to removed the virus!

Posted on Oct 03, 2007

  • 1 more comment 
  • carlos fernandez Jr.
    carlos fernandez Jr. Oct 03, 2007

    you can reformat your MP3 with twister series thats connect to software to your MP3! the doomboot is very danger to your Mp3. no one can resolved it unless if you have twister series gadgets.

  • carlos fernandez Jr.
    carlos fernandez Jr. Oct 03, 2007

    because your doomboomt is active! reformat your mp3 with twister series!

  • carlos fernandez Jr.
    carlos fernandez Jr. Oct 03, 2007

    only celpon repair shop is that we have go to cp shop!

×

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Ok now my sansa clip is acting crazy,1st off,it wont barely even come on cause everytime i try,it say "sandisk" then it turn around and say "goodbye" when i know i connected it to the computer for a few...


Try reflashing the firmware for your device you can find the latest firmware and flashing utilities from the manufacturer?s website. Make sure that you back your music up first because when you do this you are setting it back to factory settings.

Oct 01, 2009 | SanDisk Sansa Clip MP3 Player

1 Answer

My Sansa Clip wont turn on.


I just had the same problem. Hold the switch to the on position for 15 Seconds. It worked for me.

Aug 24, 2009 | SanDisk Sansa Clip MP3 Player

1 Answer

My mp3 player wont get past the start up screen


Make sure the hold/lock is not engaged, and that you have reset the player.

These are the most common methods for recovering Sandisk's Sansa Mp3 Players. I have been almost universally successful in recovering Sansa players using one or a combination of these methods. These methods do not work if you are having synchronization or music format issues - they are for recovering a player that will not power up, freezes, flashes, is not recognized by the computer, and a host of other issues.

Reset the Sansa Player first. On most models, restart is done by holding the power button in for 15 seconds or longer. Check your specific manual to be sure. The manuals are available from the Sansa website if they have been misplaced.
Download the Sansa Recovery Tool from the Sansa website.
Format - Erases Everything: Connect your Sansa player to the computer and open Windows Media Player. Click on the Sync tab. Pull down the drop down menu underneath the Sync tab by moving your cursor over the Sync tab and left clicking on the little black arrow underneath the Sync tab. Highlight "Sansa 1GB" (wording may vary slightly), and then select "Format." - this should erase everything.
Firmware Upgrade- Erases Everything: Get the latest firmware upgrade from Sansa - it updates the firmware and erases every song in the player all at once. Note: this method doesn't work if already have the latest firmware. Go to this website and click "Firmware Updater" to find out: http://www.sandisk.com/DriverDownload/driverList.asp
If these fail, then:
Try this: disconnect the player from the computer, turn it off, hold in the volume + button, and reconnect the player to the computer while holding the volume + button in. Keep holding the volume + button for an additional 5-50 seconds. Windows should eventually go into recovery mode and revive the player- it will pop up a window that says Found New Hardware Wizard.
If you get the problem where MTP Device keeps popping up continuously, uninstall the “MTP Device” by going to Start à Control Panel àSystem à Hardware à Device Manager (you computer may vary slightly, depending on Windows Version).
You may have to restart your computer after each of these methods to get them to work properly. Disconnect your Sansa player BEFORE shutting down your computer.
-Tha Mp3 Doctor

Feb 19, 2009 | SanDisk Sansa Clip MP3 Player

1 Answer

My sansa e250 gets frozen


These are the most common methods for recovering Sandisk's Sansa Mp3 Players. I have been almost universally successful in recovering Sansa players using one or a combination of these methods. These methods do not work if you are having synchronization or music format issues - they are for recovering a player that will not power up, freezes, flashes, is not recognized by the computer, and a host of other issues.

Reset the Sansa Player first. On most models, restart is done by holding the power button in for 15 seconds or longer. Check your specific manual to be sure. The manuals are available from the Sansa website if they have been misplaced.
Download the Sansa Recovery Tool from the Sansa website.
Format - Erases Everything: Connect your Sansa player to the computer and open Windows Media Player. Click on the Sync tab. Pull down the drop down menu underneath the Sync tab by moving your cursor over the Sync tab and left clicking on the little black arrow underneath the Sync tab. Highlight "Sansa 1GB" (wording may vary slightly), and then select "Format." - this should erase everything.
Firmware Upgrade- Erases Everything: Get the latest firmware upgrade from Sansa - it updates the firmware and erases every song in the player all at once. Note: this method doesn't work if already have the latest firmware. Go to this website and click "Firmware Updater" to find out: http://www.sandisk.com/DriverDownload/driverList.asp
If these fail, then:
Try this: disconnect the player from the computer, turn it off, hold in the volume + (REC button for Sansa e200 series) button, and reconnect the player to the computer while holding the volume + (REC button for Sansa e200 series) button in. Keep holding the volume + (REC button for Sansa e200 series) button for an additional 5-50 seconds. Windows should eventually go into recovery mode and revive the player- it will pop up a window that says Found New Hardware Wizard.
If you get the problem where MTP Device keeps popping up continuously, uninstall the “MTP Device” by going to Start à Control Panel àSystem à Hardware à Device Manager (you computer may vary slightly, depending on Windows Version).
You may have to restart your computer after each of these methods to get them to work properly. Disconnect your Sansa player BEFORE shutting down your computer.
-Tha Mp3 Doctor

Dec 24, 2008 | SanDisk Sansa e250 MP3 Player

1 Answer

Freeze on goodbye - Sansa e250


make sure to turn off hold/lock
These are the most common methods for recovering Sandisk's Sansa Mp3 Players. I have been almost universally successful in recovering Sansa players using one or a combination of these methods. These methods do not work if you are having synchronization or music format issues - they are for recovering a player that will not power up, freezes, flashes, is not recognized by the computer, and a host of other issues.

Reset the Sansa Player first. On most models, restart is done by holding the power button in for 15 seconds or longer. Check your specific manual to be sure. The manuals are available from the Sansa website if they have been misplaced.
Download the Sansa Recovery Tool from the Sansa website.
Format - Erases Everything: Connect your Sansa player to the computer and open Windows Media Player. Click on the Sync tab. Pull down the drop down menu underneath the Sync tab by moving your cursor over the Sync tab and left clicking on the little black arrow underneath the Sync tab. Highlight "Sansa 1GB" (wording may vary slightly), and then select "Format." - this should erase everything.
Firmware Upgrade- Erases Everything: Get the latest firmware upgrade from Sansa - it updates the firmware and erases every song in the player all at once. Note: this method doesn't work if already have the latest firmware. Go to this website and click "Firmware Updater" to find out: http://www.sandisk.com/DriverDownload/driverList.asp
If these fail, then:
Try this: disconnect the player from the computer, turn it off, hold in the volume + button, and reconnect the player to the computer while holding the volume + button in. Keep holding the volume + button for an additional 5-50 seconds. Windows should eventually go into recovery mode and revive the player- it will pop up a window that says Found New Hardware Wizard.
If you get the problem where MTP Device keeps popping up continuously, uninstall the “MTP Device” by going to Start à Control Panel àSystem à Hardware à Device Manager (you computer may vary slightly, depending on Windows Version).
You may have to restart your computer after each of these methods to get them to work properly. Disconnect your Sansa player BEFORE shutting down your computer.
-Tha Mp3 Doctor

Oct 22, 2008 | SanDisk Sansa e250 MP3 Player

1 Answer

WONT TURN ON AT ALL


Make sure the hold/lock switch is not engaged.
Try another USB port.

These are the most common methods for recovering Sandisk's Sansa Mp3 Players. I have been almost universally successful in recovering Sansa players using one or a combination of these methods. These methods do not work if you are having synchronization or music format issues - they are for recovering a player that will not power up, freezes, flashes, is not recognized by the computer, and a host of other issues.

Reset the Sansa Player first. On most models, restart is done by holding the power button in for 15 seconds or longer. Check your specific manual to be sure. The manuals are available from the Sansa website if they have been misplaced.
Download the Sansa Recovery Tool from the Sansa website.
Format - Erases Everything: Connect your Sansa player to the computer and open Windows Media Player. Click on the Sync tab. Pull down the drop down menu underneath the Sync tab by moving your cursor over the Sync tab and left clicking on the little black arrow underneath the Sync tab. Highlight "Sansa 1GB" (wording may vary slightly), and then select "Format." - this should erase everything.
Firmware Upgrade- Erases Everything: Get the latest firmware upgrade from Sansa - it updates the firmware and erases every song in the player all at once. Note: this method doesn't work if already have the latest firmware. Go to this website and click "Firmware Updater" to find out: http://www.sandisk.com/DriverDownload/driverList.asp
If these fail, then:
Try this: disconnect the player from the computer, turn it off, hold in the volume + button, and reconnect the player to the computer while holding the volume + button in. Keep holding the volume + button for an additional 5-50 seconds. Windows should eventually go into recovery mode and revive the player- it will pop up a window that says Found New Hardware Wizard.
If you get the problem where MTP Device keeps popping up continuously, uninstall the “MTP Device” by going to Start à Control Panel àSystem à Hardware à Device Manager (you computer may vary slightly, depending on Windows Version).
You may have to restart your computer after each of these methods to get them to work properly. Disconnect your Sansa player BEFORE shutting down your computer.
-Tha Mp3 Doctor

Oct 21, 2008 | SanDisk Sansa Clip MP3 Player

6 Answers

My scandisk sansa clip mp3 player is fozen at the refresh database screen


I actually called the 800 sandisk number and the guy was helpful (after some annoying personal questions).
Unplug from your computer
Turn off the device.
Push the button down to be in the "Hold" position
Press down on the "center" button (inside the circle)
While still pressing on the center, plug in the device.
Now you should be able to see the device under "My Computer"
Right click on it and FORMAT --YOU WILL LOSE ANYTHING THAT WAS ON IT! But you will be able to use it again. I was assuming all my stuff was gone, it was just copies from my computer anyway.

This worked for me and now I just have put my music back on it.

Hope this helps everyone else! And don't hook it up to a MAC!! Even just to charge it!


Feb 16, 2008 | SanDisk Sansa Clip MP3 Player

1 Answer

Even after resetting my e250, i still get the sandisk screen and it wont go to my menus after i restart it!


I Think You Should Try Starting Your Sansa In Recovey Mode ( Put The Sansa On Hold, Hold Down The Record Button While Turning The Sansa On) Then Plug It In To Your PC  Than Update Your Firmwire

Jan 31, 2008 | SanDisk Sansa e250 MP3 Player

1 Answer

Dropped MP3 Player/blank screen


Try pressing and holding the power/ menu button while holding down the play/ pause button. Do this till the screen says goodbye or turns off!!

Dec 31, 2007 | SanDisk Sansa e250 MP3 Player

1 Answer

IT wont turn on


tyr holding both the power button and the play button for 20seconds at the sametime

Dec 28, 2007 | SanDisk Sansa e260 MP3 Player

Not finding what you are looking for?
Audio Players & Recorders Logo

Related Topics:

294 people viewed this question

Ask a Question

Usually answered in minutes!

Top Audio Players & Recorders Experts

 Grubhead
Grubhead

Level 3 Expert

5342 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17130 Answers

The Knight
The Knight

Level 3 Expert

75169 Answers

Are you an Audio Player and Recorder Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...