Question about Konica Minolta bizhub C250 All-In-One Laser Printer

5 Answers

Error Message C3451

Error displays on main screen stating "malfunction detected. Please call your technical representative" C3451 Any one know what that means and how to fix it? Kindest Regards

Posted by on

Ad

5 Answers

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Expert
  • 146 Answers

It is a fuser error.

Try resetting. To reset a Rank A error follow these steps:

1. Turn OFF the Main Power Switch.
2. Turn Main Power Switch ON while pressing the Utility/Counter key.
3. Touch [Trouble Reset].
4. Check to make sure that [OK] is displayed and the it has been reset.
5. After turning off the Main Power Switch, turn it on again more than 10 seconds after and check if the machine starts correctly.
If the error recurrs then do the following:
1 Check the Fusing Unit for correct installation (whether it is secured in position).
2 Check the Fusing Unit, PWB-M and PU1 for proper connection and correct or change as necessary.
3 Change Fusing Unit
4 Change PWB-M
5 Change PU1

Posted on Jan 04, 2008

  • Kasun Dharaka
    Kasun Dharaka Nov 08, 2013

    Thank You So Much

  • Imran Khan
    Imran Khan Jun 13, 2017

    thanks its work good job. keep helping peoples

×

Ad
  • Level 1:

    An expert who has achieved level 1.

    New Friend:

    An expert that has 1 follower.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 1 Answer

1. turn off your machin.
2. Pess Stop/Reset button and turn on power button.
3. your machine will be ok
thanks.
imranhossain143@rediffmail.com

Posted on Jun 27, 2013

Ad
  • Level 1:

    An expert who has achieved level 1.

    New Friend:

    An expert that has 1 follower.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 2 Answers

Basically the fault is with your fuser unit. Or to be more precise , your unit is not detecting the right temp. in the preditermd time
1.Check the Fusing Unit for correct installation
2.Check the Fusing Unit, PWB-M for proper
connection and correct or change as necessary
ecured in position).
3.Reinstall Fusing Unit
4.Change Fusing Unit
5.also might be the thermistors

good luck g

Posted on Nov 19, 2007

1.Check the Fusing Unit for correct installation
2.Check the Fusing Unit, PWB-M for proper
connection and correct or change as necessary
ecured in position).
3.Reinstall Fusing Unit
4.Open the PWB-P and press reset buton.
If the fuser is OK and jus is overheat will be again operational.

malintzin

Posted on Apr 26, 2008

  • Sujal Sujeel
    Sujal Sujeel Feb 15, 2014

    juat i need solv this problam c3451

×

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Check firmware levels

Posted on Jul 30, 2008

3 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Kevin Hayes
  • 167 Answers

SOURCE: Error C3451 ! Anyone? Pretty Please.

This is an indication of a reoccurring error or faulty part. You MUST place a service call.

Posted on Jan 08, 2008

Kevin Hayes
  • 167 Answers

SOURCE: Error message C4551 anyone? pretty please.

This indicates you have a reoccuring error or faulty part. You MUST place a service call for this.

Posted on Jan 08, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Konica-Minolta bizhub 215 giving c3451 error message?


Error c3451 is a warm up error meaning the machine has not yet reached the correct temperature within a specific time. To Reset switch machine off using the switch inside the front door, not the one on the control panel. While holding the UTILITY key down on the control panel switch the machine back on keeping the UTILITY key held down. Eventually a Trouble reset key will be displayed in the LCD screen. Tap that, OK will be displayed then turn off the machine and then turn it back on. This will reset the error code, if the code reoccurs then there will be a problem with the fuser unit in the machine, and this will require replacing

Sep 18, 2015 | Konica Minolta bizhub Office Equipment &...

1 Answer

Malfunction c3451 detected for bizhub 250 konica minolta


Hi,
Hi,
Try this It could do the trick for you.

The error code c3451 refers to a copier warm up error; the machine had not reached the correct temp within a specific time.
I bet it happened when you first switched on one morning.
Easy to reset and fault usually goes away.

To Reset switch machine off using the switch inside the front door, not the one on the control panel.
Whilst holding the UTILITY key down on the control panel switch the machine back on keeping the UTILITY key held down. Eventually a Trouble reset key will be displayed in the LCD screen, touch this, OK will be displayed then power the machine off and then back on.

This will reset the error code, if the code reoccurs then there will be a problem with the fuser unit in the machine, and this will require replacing.

Read More...
Error Message C3451 and Printer Support and Konica Printer Support

Jul 23, 2014 | Office Equipment & Supplies

1 Answer

C450 c-0204


Remove the 2nd draw and ensure no paper behind it, THEN REMOVE ALL PAPER IN THE DRAW ON THE LEFT SIDE IT IS NOT A STORAGE AREA!!!! IT is use for 11 x 17 paper, or you have a burned out motor worse case a burned out motor that took the main control board that controls the motor also.

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

Feb 24, 2014 | Konica Minolta Office Equipment & Supplies

1 Answer

C-2557


C 2557 - ATDC sensor error.You need to replace the developer in imaging unit.

Jan 03, 2014 | Konica Minolta Office Equipment & Supplies

2 Answers

Malfunction(Code 3451) of Bizhub C252


This is a fuser heat error. The fuser unit is located in the area where the paper exits the machine. It heats up and "fuses" the toner onto the paper. The error code means that it did not heat up properly. This means you will most likely need a service person to come out and diagnose the problem.
You can try to reset the error but I doubt it will help.
Turn off the MAIN power switch (not the one on the control panel)
Now hold down the utility key while turning on the main switch and continue holding the utility key for at least 10 seconds. You should see a screen come up with nothing but "trouble reset"
Touch trouble reset and you should see a small "ok" come on. Then turn off then on the main switch again.
Good Luck and Thank You for using Fixya.

Apr 01, 2010 | Office Equipment & Supplies

1 Answer

Imagistics Error Code C-0B77


May want to check the stapling unit and hole punch. To reset open close front door. After openclosing finisher door

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

Jul 03, 2009 | Office Equipment & Supplies

1 Answer

Konica Minolta Error code C-D351 on a Bizhub C250


Hi

I have come across this kind of problem.

Is your BizHub on the network? If yes, please switch it off completely, and take the Ethernet cable out of the BizHub.

Wait for atleast 30 seconds and reconnect the cable. Now start the printer again and see if the error message goes away.

Hope this helps!

May 12, 2008 | Konica Minolta bizhub C250 All-In-One...

1 Answer

Error C3451 ! Anyone? Pretty Please.


This is an indication of a reoccurring error or faulty part. You MUST place a service call.

Oct 03, 2007 | Konica Minolta bizhub 250 All-In-One Laser...

3 Answers

Error message C4551 anyone? pretty please.


Hi,

C3451: Heat. Heater Trouble

You have to check machine fuser unit .
May be paper on the fuser unit. Check fuser unit rollers.

After check fuser unit you have to ececute a "trouble reset".

Turn on your machine by press and hold "utility counter" botton, after some seconds press to display "TROUBLE RESET" and turn off and on machine.


C4551: Cyan laser Malfunction

Check cyan laser connection and execute trouble reset.

Bye.

Oct 03, 2007 | Konica Minolta bizhub 250 All-In-One Laser...

3 Answers

Konica Milota Bizhub C250 Error Message


First power off the printer completely. Then power it back on while holding the UTILITY/COUNTER button. You will see the minolta logo, then you will see a troubleshoot reset button. Press it, you will see an OK result. Power off the printer again, then power it back on without holding the button and everything should work.

Aug 13, 2007 | Konica Minolta bizhub 250 All-In-One Laser...

Not finding what you are looking for?
Konica Minolta bizhub C250 All-In-One Laser Printer Logo

10,681 people viewed this question

Ask a Question

Usually answered in minutes!

Top Konica Minolta Office Equipment & Supplies Experts

Norman  J Weimar Jr
Norman J Weimar Jr

Level 3 Expert

6696 Answers

Adorjani Laszlo

Level 3 Expert

1297 Answers

carpediemweb

Level 1 Expert

47 Answers

Are you a Konica Minolta Office Equipment and Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...