Question about 2wire HomePortal 1800HG Router (1000400229000)

3 Answers

2wire Router cannot connect to K Corp KLS-611 adapter 802.11g

Router model 1701 HG Gateway 2Wire I was connect to the 2wire site 192.168.1.64 i was making alteration to encrytion from wep to wpa after i pressed enter, my adapter cannot communicate with the router my adapter card is a kcorp lifestyle KLS-611 It must be the encription on the adapter is not set to wpa, but on box its says can do. I need help in settings on adapter, not able to log into 2wire site to changesetting there

Posted by on

  • johncare Oct 01, 2007

    yes there is a reset, i have done that, but does that reset on the 192. address, because thats password protected

  • johncare Oct 02, 2007

    Yes

    First RESTset Modem, its recessed on unit /Router

    Then uplug everything inlc tele line

    Plug in power & ghroadband into Router

    U should see Power & Broad band Lights ON

    Go to Adaper

    U should see yr 2wire there
    Click connect

    The Key u enter is on base of the router

    U then need to complete setup
    Open browser
    type in 192.168.1.254
    That should get u into 2wire page
    U notice there is on bottom right SETUP

    U need to complete that, u might need help from yr broadband provider

×

Ad

3 Answers

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

If you wantd to change the type of encryption from WEP to WPA...aside from accessing the modem through 192.168.1.254....this ip is used on 2wire1000hg series, 2wire1800hg, 1701hg, 2701hg-b and 2700hg-b

*then you might need to indicate the modem password
*if you know it...indicate so, if not, click on the link that says "I forgot password", it would give you a hint...if you still forgot it, click on "I still forgot password"
*after that you need to click on "home network" which is the icon on the top portion of the page
*then you need to click on "wireless settings"
*under "wireless security" you would be able to change the "authentication", whether it is WEP-OPEN, or WPA-PSK"

- you could also go to: 2wire.com for help, just go to the support section
- or you could also see some simulators if you need one on shasta.2wire.com

Posted on Apr 26, 2008

Ad

I moved and the movers lost the power supply for my @ Wire router, it is model HomePortal 1000S. The serial number is 432111000622Please advise where I can obtain a replacement

Tom Crum ? Tradco, Inc. 305 W. Fyffe Ave. Suite 100 Stockton, CA 95203

Thank you for your attention.

Posted on Jul 01, 2008

Ad
  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 9 Answers

There may be a reset button on the back of the router that will set all of its settings to default. If there is it will probably be the kind you need a paper clip to press.

Posted on Oct 01, 2007

  • Omikron Oct 01, 2007

    What do you mean does it reset on the 192 address? I doesn't need to reset the IP.

×

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2wire 1701 hg dsl connection drops when laptop is connected via wireless


This is a known issue with this model.. The power supply is not large enough to handle the extra current that is needed when the unit broadcasts on wifi.

May 05, 2017 | 2wire Computers & Internet

1 Answer

How do I get my brother 1250 printer to print automatically? It used to print automatically when I clicked on Print but now I have to go into the ?Print Options and click on the Hold button twice before...


2wire lost password reset 2wire dsl modem sbc 2wire router modem unlock 2wire 2wire 1701 hg ... 2wire homeportal 2wire 2700 2wire can't get ip address .... default 2wire password 2wire modem att white paper 2wire gateway ip address .... usb 2wire hpna linux working for 2wire wrt350n and 2wire modem ...
groups.google.com/group/alt.languages.catalan/.../a1f780eac37721f2



The 2Wire HomePortal is a wired solution that offers subscribers hassle-free, ... Cisco-Linksys EtherFast Cable/DSL Router with 4-Port 10/100 Switch ... 5.0 out of 5 stars I could not ask for anything better than this., December 17, 2006 ... I waisted my money. My tech guy said it was an older generation unit, ...
www.amazon.com › Video GamesMac GamesHardware

Jul 20, 2010 | Brother HL 1250 Laser Printer

1 Answer

Lost the set up cd for 2wire 1701 hg gateway. how can I get another one?


I suggest you contact 2wire support here, and ask about getting a replacement. Either that or contact your ISP, who sold you the modem. They may have a replacement available.

I hope this information allows you to resolve this issue. If you need further assistance, please post back with a comment to this thread.
If I've managed to answer your question or solve a problem, please take just a moment to rate this post....thanks!

Jan 25, 2010 | 2wire 2700HG-B Router (2700HGB)

1 Answer

Wireless hookup (Roku player) to DSL 2WIRE 1701 HG Gateway


make sure to configure the wireless settings of your roku player matching the wireless settings of your router. You need to do manually, go to the network settings of your roku, go to wlan settings and edit the SSID and wireless security key

Jun 28, 2009 | 2wire (1000-400108-001) Router

1 Answer

I use 2wire 1701 HG Gateway for 3 computers. I have been using a Plug and Play network with a password. My primary computer harddrive crashed. I had the drive replaced, but I have been unable to reconnect...


Hello hopefully ican hel solve your issue i have a 2wire modem myself ans have found that 2wire products are very picky. To answer your question for 2wire products when you try to connect wirelessly it wants you to type in the wep key which is the serial number of the product otherwise you are unable to connect. Now as far as losing your password if you are able to get into the 2wire product via browser so you can bring up the main software page you can try to see if you can get too any info that relates to resetting your info like username and password. Otherwise do a search for your product and search forums and you will most likely find someone that has had to recover there info and they will tell you how they do it. Good luck

Feb 23, 2009 | 2wire (1000-400108-001) Router

2 Answers

2 wire 2700 hg-b


The 2Wire 2700 is a residential gateway, a modem and router in-one. There is an RJ-11 jack in the back of the gateway and this is where your dsl phone cord plugs in. There are four RJ-45 jacks in the back for connecting devices using ethernet cable. As a router is can operate both wirelessly and wired. For wireless operation you'll need the WEP key which is located on the tag on the bottom of the gateway. It's the number enclosed in brackets, between the two bar codes.

Redneck Geek

Sep 09, 2008 | 2wire 2700HG-B Router (2700HGB)

1 Answer

2wire 1701 HG Gateway wireless not working


Hi,

There could be a lot of possibilities why you lost your connections at the same time. Could be windows update or changes had been made in your 2wire 2701 HG.Its impossible to say that your wireless adapters turned bad all at the same time.As what you observed , wireless light is off meaning your 2wire doesnt detect any wireless connection. You can try reconnecting them 1 at a time by going to your wireless connection tool or network connections.

If that didnt help, you can use your PC w/c is connected using the USB connection. Using this step, you 'l have a chance to edit and view your wireless network. For you to access your 2wire you must know what your 2wire address {default gateway}. Using your hardwired pc go to start > run > type in cmd then hit enter > on the Dos command screen type in ipconfig and hit enter> youl see your default gateway . It would look like this 192.168.1.254 for example cos sometimes it would vary depending what ISP you have, Open your fav browser and on your address bar type in your default gateway. That would lead you to your 2wire page, there youl have a chnace to view you home network. Check if your wireless encryption and you network name if everything is still the same. {Best thing is to change your wireless name or SSID. Then try to reconnect on your wireless connection for each computer and make sure you have your wireless encryption.

Hope that helps. Pls let me know asap if you need clarifications.

Cheers.



Jun 15, 2008 | Computers & Internet

4 Answers

2wire 1701 HG configuration/connectivity problems


try to reset the 2wire by holding the reset button in with a pin for a good 20 seconds, wait for all the lites to return, then try a large download again...if problem is not solved, try http://www.2wire.com/?p=72

if no luck there....replaced the router.

Nov 10, 2007 | 2wire (1000-400108-001) Router

Not finding what you are looking for?
Computers & Internet Logo

606 people viewed this question

Ask a Question

Usually answered in minutes!

Top 2wire Computers & Internet Experts

Prashant M
Prashant M

Level 3 Expert

2263 Answers

Michael Galve
Michael Galve

Level 3 Expert

1269 Answers

Ron Stone

Level 2 Expert

223 Answers

Are you a 2wire Computer and Internet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...