Question about Kodak EasyShare CX7330 Digital Camera

3 Answers

Turn on camera and set date and time shows up

When I turn on my cx7330, the screen shows up with set date or cancel option I can move the up down arrows however if I press ok nothing happens and I can;t take a picture because I can't get off this screen. HELP

Posted by on

  • Anonymous Nov 12, 2007

    I have the same problem only first the green light flashes for several minutes then the set date screen shows and the ok button wont work. Several more minutes then the lens opens and camera is functional. Shut it off and same thing happens over again ad nauseum. Have tried everything on the support screens that seemed applicable but no joy. Cannot find a1 800 to talk to areal person at Kodak.........Help please

×

Ad

3 Answers

  • Level 1:

    An expert who has achieved level 1.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 1 Answer

Take your camera apart and put a piece of electrical tape over the center button (ok) on the menu.
Worked just fine for me after that.

Posted on Jul 28, 2009

Ad
  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Its not the batteries, if you have been using the camera for an extended amount of years the rubber under the ok button builds up a rubbery gook, take it apart and clean the gook off with a q-tip and it will work perfect, same thing happed to me.

Posted on Jul 01, 2009

Ad
  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Governor:

    An expert whose answer got voted for 20 times.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

  • Expert
  • 110 Answers

Are you using Lithium batteries?

Using alkaline batts (or less) often creates 'issues'.

Worth a try if you haven't been using Lithium batts.

Posted on Dec 28, 2007

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Have never set date on my camera. What do I need to do to accomplish this? Do I needsoft ware, any cords, etc? Tried to go by instructions on line but it didn't work. What am I missing? Thanks


Welcome to FixYa,


Hi I have here the steps on how you can update the date and time of your digital camera. You can chaged it if its your first time to set the date and then you also have here the steps if you want to changed it anytime you want.


Setting the date & time, first time

The Date and Time have been reset message appears the first time you turn on

the camera or if the batteries are removed for an extended time.

1 SET DATE & TIME is highlighted. Press the OK button.

(Select Cancel to set the date and time at a later time.)

2 Go to step 4 below, Setting the date & time, anytime.


Setting the date & time, anytime

1 Turn on the camera. Press the Menu button.

2 Press to highlight Setup Menu , then press the OK button.

3 Press to highlight Date & Time , then press the OK button.

4 Press to adjust the date and time. Press to advance to the next

setting.

5 When finished, press the OK button.

6 Press the Menu button to exit the menu.


Reminders:Depending on your computer operating system, Kodak EasyShare software may let your computer update the camera clock when you connect the camera.


I hope this steps will let you to resolved your issue.

Feel free to reply on this e-mail if this steps will work or won't work.


Thank you for using FixYa.

Mar 23, 2011 | Kodak EasyShare CX7330 Digital Camera

Tip

Stamp Date and Time on Photos in Canon Digital Cameras


Hello Dear,

In all Canon PowerShot and IXUS series cameras date and time can be stamped on the photos shot in Post Card Size, to set the Camera into this mode do the following:
On Camera in Shooting mode (Live view is visible on LCD)
Press Function/Set button once
From right-left move to the Post Card Size
Press Function/Set again.
Now, Press Menu Button
From up-down move down
On Stamp Date (Option Name written, Visible on the Right top Corner of Screen)
From right-left move and select you want only Date or Date and Time both.
Press Menu again
Now, you are ready.

For more clarification please revert.

Warm Regards,
Joseph Manoj

on May 26, 2010 | Cameras

2 Answers

When I print photos, it doesn't show the date on the photo. Also , when I scroll down to Date/Stamp on the menu, it is always "off". And I can't change the setting. Help


You haven't said what make/model your camera is, so it is hard to advise.

Without knowing the camera, I am guessing that you may be in the wrong mode when trying to change this setting. You won't be able to change it while reviewing pictures already taken. You can only change it for pictures to be taken subsequently. Once pictures are taken, you won't be able to add the date stamp, nor remove it if it has been stamped.

It may be that it won't allow you to set this if you haven't already set the date and time in your camera. I can't see why this setting would be shown at all if it was not possible to turn it on (i.e. if your camera did not have this feature).

Nov 03, 2010 | Cameras

1 Answer

How to seup date and time on the screen when we


Hello Dear,

In all Canon PowerShot and IXUS series cameras date and time can be stamped on the photos shot in Post Card Size, to set the Camera into this mode do the following:
On Camera in Shooting mode (Live view is visible on LCD)
Press Function/Set button once
From right-left move to the Post Card Size
Press Function/Set again.
Now, Press Menu Button
From up-down move down
On Stamp Date (Option Name written, Visible on the Right top Corner of Screen)
From right-left move and select you want only Date or Date and Time both.
Press Menu again
Now, you are ready.

For more clarification please revert.

Warm Regards,
Joseph Manoj

May 22, 2010 | Canon Cameras

1 Answer

Change the date


-Turn On camera
-Press menu button to show an options screen
-Go to setup menu or a Icon of a Wrench thats the setup
-Under setup Press down arrow 12 times to show he date and time
-Press Ok buttton again if you already on the date and time to adjust the date setting and time

-Gudluck!

Nov 06, 2009 | Kodak Z8612 Digital Camera

1 Answer

We can turn on the camera, but the OK button does not wok.


hi try to reset ur camera...To do such reset, turn on the camera and hold the menu button down for longer than 5 seconds. A message should hopefully come up on your LCD asking if you want to reset the camera. Select Yes...
thank u!!!
rate me!!

Jul 27, 2009 | Kodak EasyShare CX7330 Digital Camera

1 Answer

Can't reset Date & Time


What you have to do is go to the icon with the spanner (as shown above) and keep tabbing down. There are more options than just the ones you see in the screen (not just High Power , Auto, Set Tag, On), keep going down and it will show you the other options. You will see the date change icon about 7 or 8 down.

May 22, 2009 | Kodak EASYSHARE M1063 Digital Camera

2 Answers

How to set date and time


What you have to do is go to the icon with the spanner (as shown above) and keep tabbing down. There are more options than just the ones you see in the screen (not just High Power , Auto, Set Tag, On), keep going down and it will show you the other options. You will see the date change icon about 7 or 8 down.

Vitally

May 12, 2009 | Kodak EASYSHARE M1063 Digital Camera

2 Answers

Kodak CX7330. turns on but LCD screen is black and won't take a pic


It sounds like a bad connection on the ribbon cable of the LCD screen to the camera's motherboard. The fact that when you physically move the camera around and you can get the screen to then work, tells me something is loose inside.

Good luck!

- Jim

Jan 14, 2008 | Kodak EasyShare CX7330 Digital Camera

1 Answer

Kodak easyshare CX7430


My Kodak camere was really not dropped. I put in new batteries and the camera only gives me one shot and I have to turn it off and try again. I can plug the camera into a charge cord and I can take all the pictures I want. Is it possible the 2 batteries are not enough to power the camera

Mar 28, 2007 | Kodak EasyShare CX7430 Digital Camera

Not finding what you are looking for?
Kodak EasyShare CX7330 Digital Camera Logo

Related Topics:

166 people viewed this question

Ask a Question

Usually answered in minutes!

Top Kodak Cameras Experts

Donald DCruz
Donald DCruz

Level 3 Expert

17130 Answers

Jerry Greenberg
Jerry Greenberg

Level 3 Expert

1689 Answers

Computer Links

Level 3 Expert

2386 Answers

Are you a Kodak Camera Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...