Question about Washing Machines

1 Answer

Washing maching belt replacement

White Westinghouse # wwx233rbs1 washer I can't seem to get it on its to tight

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Expert
  • 209 Answers
Re: washing maching belt replacement

Some machines have stretch belts and are difficult to place, if you have the right belt for the model then its just persistence, believe me we as engineers have same trouble (if we are honest)

Posted on Oct 02, 2007

Add Your Answer

0 characters

Uploading: 0%


Complete. Click "Add" to insert your video. Add


3 Points

Related Questions:

2 Answers

Maytag bravos washer making a grinding noise. It seems to make this noise when the drum is moving, any suggestions?

Unplug machine and tilt it back. Pull down the white insulation board. remove the two screws holding the white/clear plastic guard in place 5/16 nut driver. and check the gear and belt ours had come off. Now it works just like new you will need a 13mm hex for putting the gear back up.

Apr 28, 2012 | Maytag Bravos 3.8 Cu. Ft. Washer

1 Answer

I have a 10 year old White Westinghouse washer. I don,t know the model #. It is heavy duty. Is it direct drive , or is it belt driven

Its belt driven only washer made by the Whirlpool corp. were direct drive during that time period 10 years ago

Sep 14, 2011 | Westinghouse Washing Machines

2 Answers

Does anyone know where can I buy a new belt for my Tecnik tkl 9260 washing maching? Tecnik customer service won't pick up the phone and Spares2go seem to think this appliance has too different belts...


Your washing machine only has one belt. The reason for the two different part numbers is that the original part (1192J5) is no longer manufactured/available. 1185J5E is the replacement part number which is fully compatible with your machine. An appliance spares supplier should have been able to tell you this.

You can order using either part number - some suppliers will have the part listed under both numbers, others may still have stock of the original 1192J5 part.

I generally use UK Whitegoods for appliance spare parts as their prices are good, they deliver quickly and if you need any advice on ordering the correct part, you will get the right information:

Your belt:
Home page:
Parts enquiry:

Hope this helps!


Nov 25, 2010 | Tecnik TKL9260 Front Load Washer

1 Answer

I just replaced the belt on my White WESTINGHOUSE la 560axw2 WASHER. It is now severely out of balance whenever it reaches the spin cycle.

The problem may be with the top springs may be damaged you can replace the spring set completely to get the smooth running in the spin

Dec 30, 2009 | Westinghouse WWS833ES Super Capacity Top...

1 Answer

My washing machine does not have a spin cycle

I just solved this problem myself. It's the lid lock mechanism which is located under the top cover. When I manually moved the aluminum locking tab over my washer prompty drained and spun. There are four wires total going to the switch. Well, the solid white and the white/red wires control the lid lock mechanism. You can either replace the entire switch or bypass the lid lock by wire nutting the two wires I previously mentioned together. Now, if you bypass, be forewarned the lid will open while the washer spins very fast which presents a potential danger. For immediate use, bypass until you get the replacement switch. Hope this helps your problem.

May 10, 2009 | Westinghouse WWS833ES Super Capacity Top...

1 Answer

White-Westinghouse washer will spin but water will not spin out

no its a remote electric pump,no belt.its ither blocked or fail.cut power,pop top remove frount cover an you will see pump.white or tan.remove hoses[watch out 4 water and check 4 blockage

Jan 02, 2009 | Westinghouse WWS833ES Super Capacity Top...

1 Answer

Won't agitate or spin

Try to replace lid lock which is located below the top cover

Feb 10, 2008 | Washing Machines

1 Answer

Removing motor to replace belt for agitator

first unplug washer then there are 4 half inch bolts on the motor holding it to the frame take those out unplug the motor harness. then twist it out you may have to take the hoses off. then there are 3 torxs screws in the pump take them out and put new belt on same way you took off and then reverse the steps and you will be ok

Jan 30, 2008 | Amana NAV8805EWW 3.3 Cu. Ft. Elustra Tub...

Not finding what you are looking for?
Washing Machines Logo

Related Topics:

312 people viewed this question

Ask a Question

Usually answered in minutes!

Top Washing Machines Experts

Dan Webster
Dan Webster

Level 3 Expert

8147 Answers

Richard Roth
Richard Roth

Level 3 Expert

9472 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17129 Answers

Are you a Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides