Question about JVC AV-27850 27" TV

1 Answer

Tv problem i have an older mitsubihi tv its projection tv model vs5071 well i don't know where is the horozontal or vertical buttons located i need to adjust because it just keep on rolling could you please help thanks

Posted by on


1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.


    An expert who has answered 500 questions.

  • Expert
  • 556 Answers

Generally buttons are located at front only. but if it is not there then it will be inside in the shape of small variable res. called preset. vertical hold button will be near vert.section &horz hold near h/ section.

Posted on Sep 30, 2007


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

On a mitsubihi wt42311 tv where are the STK-392-110 convergence chips located?

Pretty easy to see them as they are marked with that number right on them.

They will be side by side and on a metal heat sink to keep them cool.

Dec 02, 2012 | Mitsubishi WT-42311 42" Rear Projection...

1 Answer

Mitsubishi 72" Model VS70705. Picture

The picture rolling up and down is caused by the vertical oscillator running off frequency. Usually caused by a Capicator that has burnt out and started leaking and causing the frequency to be off. Static sounds like weak signal, however the vertical oscillator could be corrupting the picture. If you are not a trained TV Technician don't try to fix it yourself. There's a lot of junk back there and knowing where the vertical oscillator section is located and which capacitor is bad will require a tech manual or a 'Sam's Photofacts' to hunt it down. dhgill1949

Jun 04, 2011 | Mitsubishi Televison & Video

1 Answer

Vertical tearing, unABLE to conver.

you can get the service manuals for most TVs at the following link, they email them.

Jun 15, 2009 | Televison & Video

1 Answer

Horizonal and vertical off.

My picture is too big for my screen also, I have a 27 inch screen and I can't see the scrolling tickers on the bottom and the baseball score readout on the top. When I turn the tv on, the heads are huge on the top and that finally comes into proportion, but it goes too far. I can't find a horozontal or vertical control in the manual or on the tv menu. What can I do?

Apr 29, 2009 | Curtis-Mathis CM27101S TV

1 Answer

Only have one horozontal line across mid screen

Horizontal line shows problem in Vertical Deflection area of TV, please check Vertical Output IC and its voltage supply. You didn't mention model and brand name so I gave you general information for that problem.

Aug 22, 2008 | Televison & Video

1 Answer

Convergence problem with Toshiba TV 42H83

I am still working on it! Need a technician in Alacante Spain!

Jul 25, 2008 | Televison & Video

1 Answer


This is a vertical-deflection problem. Try to adjust the vertical (height and linearity and hold) controls, which should be screwdriver potentiometer controls on the back of the set.

If this does not work, a defective component in the vertical-deflection circuit will need to be repaired.

I hope this helped you. :)

Mar 30, 2008 | Televison & Video

1 Answer


Older Mits TV's have a PIP circuit board that fails,upsetting the is the solution....

1) Remove PIP PC board ..... discard

2) pull chassis... on underside of main board, locate VP plug

3) Using 22mf 50v NP capacitors, connect pin 5 to pin11
and pin 7 to pin 9......

large pix stable.....but no PIP box.....PIP PCB NLA......


Jan 27, 2008 | Mitsubishi VS-45605 50" Rear Projection...

2 Answers

My mitsubishi vs 5071

You might have a bad PIP board, When you say NO picture. Is it totally blacked out or blacked out with "blue snow". The PIP has been alot of problems in this chassis and you will experience what your describing. Capacitors are the root of the PIP boards failure. Let me know if I can assist you further.

Jan 26, 2008 | Televison & Video

1 Answer

Vertical black lines rear projection

Please provide exact model from back of tv........
Possible vertical IC circuit problem===bad caps? IC?

Nov 01, 2007 | Hitachi 50UX57B 50" Rear Projection...

Not finding what you are looking for?
Televison & Video Logo

Related Topics:

72 people viewed this question

Ask a Question

Usually answered in minutes!

Top JVC Televison & Video Experts

The Knight
The Knight

Level 3 Expert

75032 Answers

Jaime Hernandez

Level 3 Expert

2326 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17130 Answers

Are you a JVC Televison and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides