Question about Troy Bilt, Tuffy, Rear - Tine Tiller, 4.0 Tecumseh Engine

1 Answer

Replace tine shaft oil seals - Junior model

How do I remove the tine shaft oil seals on a Troy-Bilt Junior V (Mod # 15006, S/N M0104189)? The outside of the tine drive housing has a silver-colored disc about 45 mm in diameter. Does this disc come off to allow access to the seals? If so, what tool should be used to remove the disc? If not, how are the seals accessed?

Posted by on

  • Anonymous Mar 26, 2014

    Do I have to heat the tine holders to get them off the tine shaft?

×

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Expert
  • 45 Answers

On my pony the disc came off when i removed all of my tine shafts. then i pulled the old seals out an drove the new ones in

Posted on Apr 29, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Leaking tine shaft


your seal on the shaft defective,
www.ask.com/mfg.name/make/model/service/parts/leaking/tine/shaft/

Oct 02, 2015 | Troy-Bilt Troybilt Horse 6, 7 And 8 Hp...

1 Answer

The rear tine seals are leaking ive taken the bolts out but the tines will not come off what can i do


You could try putting the tiller to use, preferably where it will have to work hard to till the ground it unsuccessful you may need a torch and some good old fashion luck to loosen tines from shaft. Now consider this; if the bearings are worn so that the shaft is loose new seals will not hold up and you will risk doing further damage to the worm gear located on rear shaft and possibly other damage to your transmission from contaminated oil.

Mar 04, 2011 | Troy-Bilt Pony Garden Tiller

1 Answer

Troy bult junior has new tines , runs to fast...


MAKE TWO PASSES SET THE DEPTH GUIDE SO IT JUST BREAKS THE GROUND, DON'T TRY TO DO IT ALL AT ONCE. SOON AS THE GROUND IS LOOSE IT WILL DIG MUCH BETTER.. IT SHOULD HAVE A FORWARD AND REVERSE FOR THE TINES, GEARS FOR FORWARD REVERSE DRIVE

May 19, 2010 | Troy Bilt, Tuffy, Rear - Tine Tiller, 4.0...

1 Answer

I cannot get my oil seals of my rear tine tiller It is a Troy Bilt 5.5 hp and I got the left side off but the right side tine attachment will not budge any suggestions please


Have you tried soaking the shaft area with either PB Blaster or Deep Creep penetrating oil. Try this for a few days before trying to tackle getting the tine attachment off.

Jan 26, 2010 | Troy Bilt Pony 6.5 Hp Rear Tine Tiller

1 Answer

I need to replace the seals on my Troy-Built Pony tiller. 6 hp, ser.# 121811201149. I can not seem to remove the tine shafts. I have pulled the bolt thru the shaft but cannot budge it. Does anyone know...


I presume you opened the port and removed the grade 8 placement bolt? If you have then you need to polish the shafts with 400 then 800 sandpaper, clean then lube them before trying to slide thru the support bearings. If your tine shaft is bent? your screwed, or just remove the shaft seals with a screwdriver and replacing them without removing the shaft. REmember to put a thin coat od RTV arround the outer lip to help make a better seal

Nov 15, 2009 | Troy Bilt Pony 6.5 Hp Rear Tine Tiller

1 Answer

Troy bilt pony left side tine assembly fell off


sounds like the shaft is either bent,or the inside diameter is worn and the shaft tube needs to be replaced.

Apr 23, 2009 | Troy-Bilt Pony Garden Tiller

1 Answer

Leaks oil around the tines.


 an new oil seal needs to be put onto the output shaft of the transmission.  remove the plug wire if you attempt to pry out the old seal and tap in the new seal.  Be careful not to damage the case and grease the seal and shaft when you replace the oil seal 

Mar 29, 2009 | Troy-Bilt Garden

1 Answer

How to remove rear tines to replace seals ?


The tines sometimes get frozen to the shaft. You might try penatrating oil and use a heat gun or hair dryer to heat to loosen.
Also tap wiht a hammer around shaft.

Mar 19, 2009 | Troy-Bilt Garden

3 Answers

Oil seal for rear tine shaft


The serial number is located on a flat spot just above the right wheel shaft where the gear housing and the top gear cover meet. It will be a six digit number stamped in the metal.

Frank

Mar 11, 2009 | Troy Bilt Pony 6.5 Hp Rear Tine Tiller

1 Answer

Wheel shaft seals on troy bilt pony 7 hp.


If the seal fits over the axle shaft it should be ok. be sure your axles are very clean as not to ruin the new seals when applying them. probably a good idea to replace them as a pair (right and left side) to save you time down the road.

Oct 20, 2008 | Troy Bilt Pony 6.5 Hp Rear Tine Tiller

Not finding what you are looking for?
Troy Bilt, Tuffy, Rear - Tine Tiller, 4.0 Tecumseh Engine Logo

608 people viewed this question

Ask a Question

Usually answered in minutes!

Top Troy Garden Experts

Neil Hancock

Level 2 Expert

236 Answers

Jay Finke
Jay Finke

Level 3 Expert

1389 Answers

lnbn1975

Level 2 Expert

204 Answers

Are you a Troy Garden Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...