Question about Frigidaire Washing Machines
The washer dosnt drain, i all ready chek the pump work perfect.the washer makes a click sound but the pump dosnt work.
SOURCE: Frigidaire Front Load Washer
You need to replace the Motor controller speed asm part number 134149220 they are about 165.00. very easy part to replace you have to remove the back panel and the control board is on the bottom left side two scews and two plugs.
Posted on Dec 18, 2007
SOURCE: Washer won't drain
There was a obstructin in the motor fan blades i think there were 4 screws to remove to get 2 it, but it back together and it eas fine. I did how ever have to remove the the wire connector from the pump motor and reconnect to rerest the pump.
Thanks for the help
Posted on Jan 06, 2008
As I have not received a response, I'm assuming these hints have taken care of your problem. If you have any more troubles, feel free to drop me a note back.
Posted on Jul 09, 2008
Does the bottom of your agitator work correctly? We had the same problem if you pop the cap off the top of your agitator there is a cam in there with 3 dogs that engage the agitator causing it to spin. If the bottom part is agitating correctly then chances are the dogs in the cam assembly are shot. If the bottom is agitating correctly then it is very possible you have something stuck under the bottom section of the agitator. If this is the case remove the top cover (same as before it's just a lid that pops off) inside you will see a 1/2" square use a 1/2" drive ratchet with a 3" or 6" extension unscrew this piece remove the top section of the agitator then the bottom. Once the bottom is out check to make sure all is clear inside the washer. Reassemble in the reverse order making sure the lower section sits all the way down on the splines for the drive mechanism. If neither one of those solve the problem I would suspect you have an issue in the drive train of the washer.
Posted on Dec 30, 2008
SOURCE: Water Will not drain after cycle
The filter for the drain is located under the drum assembly. It is inside the rubber cover between the drum and the pump. It has 3 clamps that you will need to remove, than you can get at the filter inside the rubber housing. It will be clogged with coins, or lint from the wash, and once this is cleaned, the machine will work like new.
Joe the Plumber
Mid Hudson Heating & Plumbing
Posted on Feb 05, 2009
probably has something stuck in the electric drain pump happens alot on frigidaire washers it is accessable after removing front lower acess panel tilt washer back after pulling it from the wall the drain pump will be just right of center at the front use a pan to catch any water that will come out you can either remove the 2 drain hoses to clear obstruction or you can unscrew pump motor from pump body
Posted on Jul 24, 2009
Tips for a great answer:
Apr 14, 2014 | Frigidaire Affinity ATF7000E Front Load...
Hello - The error code "E20" typically means the water is not draining properly or not pumping out fast enough. Does the washer making a humming noise? If so, either the drain hose may be kinked or the drain in the house is clogged. Once you have confirmed and cleaned the hose and issue continues contact a professional to move forward accurately. The unit may possibly have a faulty pump or control board.
Oct 12, 2012 | Frigidaire Affinity ATF7000E Front Load...
Jul 28, 2012 | Frigidaire Affinity ATF7000E Front Load...
Sep 23, 2009 | Frigidaire ATF6000ES Front Load Washer
Jul 30, 2009 | Frigidaire Washing Machines
Jun 05, 2009 | Kenmore 22422 Top Load Washer
Oct 19, 2008 | Frigidaire GLTR1670A Front Load Washer
Oct 15, 2008 | Frigidaire ATF6000ES Front Load Washer
Jun 08, 2008 | Frigidaire GLTR1670A Front Load Washer
Oct 20, 2016 | Frigidaire Washing Machines
32 people viewed this question
Usually answered in minutes!