Question about Kenmore 64892 Electric Dryer

1 Answer

Kenmore dyer Dryer will stop running anywhere from 10 minutes into cycle to near the end. Can restart by pushing start button and it will run until it decides to stop. (may finish cycle or not) Seeing how it will restart with the start button I dont think it is over heating ??? Any ideas as to the problem ??? Thanks

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 447 Answers
Re: Kenmore dyer

Sounds like the timer, unless it has a Evenheat contol board and a seperate motor relay, in which case its most likely the relay, or could be the computer

Posted on Sep 29, 2007

Add Your Answer

0 characters

Uploading: 0%


Complete. Click "Add" to insert your video. Add


3 Points

Related Questions:

1 Answer

Why won't the buzzer alarm go off at the end of a drying cycle

Search Results

    Why does my Kenmore dryer model 417.94802/94862 end ... > Manage My Life > Questions
    Why does my Kenmore dryer model 417.94802/94862 end of cycle alarm go off ...washer/dryer unit I do see that it is normal for the end of cycle buzzer to go off ...Why won't my Kenmore dryer model 110.86872100 shut off at the end of the ...

    Why won't the buzzer shut off on my Kenmore 80 Series ... > Manage My Life > Questions
    The buzzer won't stop buzzing after the load is complete. ... or turn on the timer and the dryer will start just by selecting a cycle and closing the door. ... The dryer should continue to run and at the end the buzzer should only stay on as long as ...

    FIXED The Buzzer At The End Of The Dryer Cycle Comes On But Won't ...

    Dec 11, 2010 - 10 posts - ‎2 authors
    My maytag dryer has operated wonderfully until today. All of a sudden the buzzer that goes on at the end of the drying will go on but will not shut off unless I open the door.... To test it: by-pass the push-to-start switch and see if when you turn the timer on and close the door, the ... VERY annoying dryer End of Cycle Signal
    9 posts
    Jun 29, 2012
    Maytag DE8410 electric dryer - End of cycle buzzer stuck ...
    4 posts
    Mar 27, 2011
    Kenmore 80 series, buzzer won't shut off
    2 posts
    Sep 10, 2005
    More results from

Feb 08, 2016 | Whirlpool Dryers

1 Answer

My dryer wont start and the lock button is on

1) Press and hold the End Of Cycle Signal button for 3 seconds to turn this feature off.

2) When the dryer is running and Control lLcked light is on, the dryer can be stopped by pressing the Pause/Cancel button, but cannot be restarted until the control is unlocked.

Mar 13, 2011 | Kenmore Dryers

1 Answer

Dyer is getting power but will not turn on

dyer will not start with start button,but will run with cycle button in cycle when you turn it to the cycle want

Nov 14, 2009 | Kenmore 62602 Electric Dryer

1 Answer

Turns off after a few minutes

sounds like your motor is overheating or going bad. sometimes lint built up around the motor can cause it to overheat. or the motor is dying.

Aug 31, 2009 | Kenmore 73952 Gas Dryer

2 Answers

Kenmore 970 C81062 10 Electric Dyer WILL NOT

It sounds like the drum may be stuck. Turn the dryer on with the door open, just keep the button pushed. Then try to turn the drum by hand, and see if it will start to turn.

Jun 04, 2009 | Dryers

2 Answers

Kenmore dryer keeps on going and going

The timer is bad. It is located behind the knobs and can be replaced really easily. The price for a new timer is about 35 dollars. If this helped please rate

Feb 12, 2009 | Kenmore 64902 Electric Dryer

1 Answer

Kenmore 80 series dryer stoping after running for 10 to 15 minute

Start any cycle. Dryer runs for 10 to 15 minutes, then stops before cycle is complete. Start again, stops again in 10 to 15 minutes.

Nov 11, 2008 | Kenmore 63942 Dryer

1 Answer

Dryer won't stay running

since time specific i would be looking at the contro board as a problem

Apr 25, 2008 | Kenmore Elite HE4 Electric Dryer

1 Answer

Kenmor dryer Series 80 110 668 14690

based from your story, you are tiggering a thermal overheat protection device. as the device heats up, it would trip off the dryer, and comes back on again after a few minutes but as the heat increases, the device is being triggered faster until the device would no longer trips back because the dyer is so hot that it would take about 10 mins to cool down. i think this is just a secondary problem, your primary problem could be lack of air passing through the heating element. please check the stroller blade for dirt of flint and debri, check also the outlet duct, it could be clogged with flint also. i hope i was able to solve your problem.

Feb 21, 2008 | Kenmore 63942 Dryer

Not finding what you are looking for?
Kenmore 64892 Electric Dryer Logo

Related Topics:

120 people viewed this question

Ask a Question

Usually answered in minutes!

Top Kenmore Dryers Experts

Dan Webster
Dan Webster

Level 3 Expert

8147 Answers

Tim Whalen

Level 3 Expert

3056 Answers

Richard Roth
Richard Roth

Level 3 Expert

9472 Answers

Are you a Kenmore Dryer Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides