The following reset procedure will completely restore the default settings on your
D-Link
device including your password. This procedure applies to the DI-514,
DI-524, DI-604, DI-614+, DI-624, DI-754, DI-764, DI-774, DI-784,
DI-804V, DWL-700AP, DWL-800AP+, DWL-900AP+, DWL-1000AP+, DWL-2000AP,
DWL-2100AP, DWL-6000AP, DWL-7000AP, and DWL-7100AP.
Step 1 Locate the reset pinhole on the back of the unit.
Step 2
With the unit powered on, press and hold the Reset button.
Step 3 Hold the Reset button for about 10 seconds.
Step 4 Release the Reset button.
Step 5 The unit will reboot.
Allow 20-30 seconds before reconnecting.
Step 6 The device is now at factory defaults.
Note: Do not recycle power during the reset procedure.
The default user name for most D-Link devices is
admin and the password is
left blank.
Hope this helps! Give me thumbs please!
I checked the settings and they are okay, but it is still not working
Thank you for your fast answer.
I only want to have one wlan but now I have two.
You are right, the DI-524 is the DHCP router. The AP is connected via
ethernet.
DI-524 Firmware-Version: V2.03DE
DWL-G700AP Firmware Version v2.12
I´m using the same encryption on the AP and the router : Open System,
WEB-Encrytion: 64-Bit, Key-Type: ASCII
AP config:
Mode: Access Point
(I tried to put them in Repeater-Mode but then the AP finds the
existing Wlan from the router, but he can´t connect)
thernet
MAC Address
00:1b:11:e8:b8:33
IP Address
192.168.0.50
Subnet Mask
255.255.255.0
Gateway
0.0.0.0
DHCP Server
Disabled
var wlan_num = 1;
var wlanMode =new Array();
var networkType =new Array();
var band=new Array();
var ssid_drv=new Array();
var channel_drv=new Array();
var wep=new Array();
var wdsEncrypt=new Array();
var bssid_drv=new Array();
var clientnum=new Array();
var state_drv=new Array();
for (i=0; i< wlan_num; i=i+1)
{
wlan_name= "wlan"+i+"-status";
wlanMode[i] = 0;
networkType[i] = 0;
band[i] = 3;
ssid_drv[i] = 'Richard';
channel_drv[i] = '4';
wep[i] = 'WEP 64bits';
wdsEncrypt[i] = 'Disabled';
bssid_drv[i] = '00:1b:11:e8:b8:33';
clientnum[i] = '0';
state_drv[i] = 'Started';
}
for(i=0; i < wlan_num; i++){
document.write('\
\
Wireless '+'\
\
\
SSID \
' );
if (wlanMode[i] != 2)
document.write(ssid_drv[i]);
document.write('\
\
\
Encryption Function \
');
if (wlanMode[i] == 0 || wlanMode[i] == 1 || wlanMode[i] == 4)
document.write(wep[i]);
else if (wlanMode[i] == 2)
document.write(wdsEncrypt[i]);
else
document.write(wep[i] + '(AP), ' + wdsEncrypt[i] + '(WDS)');
document.write('\
\
\
Channel \
'+channel_drv[i] +'');
}//end of wlan_num for
Wireless
SSID
Richard
Encryption
Function
WEP 64bits
Channel
4
Router
config:
LAN
MAC-Adresse
00-19-5B-B4-52-41
IP-Adresse
192.168.0.1
Subnetzmaske
255.255.255.0
DHCP-Server
Aktiviert
WAN
MAC-Adresse
00-19-5B-B4-52-40
Verbindung
DHCP
Verbundener
Client.
Verbleibende
Lease-Time
01:46:46
IP-Adresse
10.0.0.1
Subnetzmaske
255.255.255.0
Gateway
10.0.0.138
Domain
Name Server
10.0.0.138
Wireless
MAC-Adresse
00-19-5B-B4-52-41
ESSID
WG-Wlan
Sicherheit
64-bit
WEP aktiviert
Kanal
7
Sorry for the last addon, I tried to copy the information from my AP and router in a table but it did not work.
I try it again:.
I only want to have one wlan but now I have two different wlan.
The DI-524 is the DHCP router. The AP is connected via
ethernet.
DI-524 Firmware-Version: V2.03DE
DWL-G700AP Firmware Version v2.12
Could anyone help me??
I´m using the same encryption on the AP and the router : Open System,
WEB-Encrytion: 64-Bit, Key-Type: ASCII
AP config:
Mode: Access Point
(I tried to put them in Repeater-Mode but then the AP finds the
existing Wlan from the router, but he can´t connect)
Can you provide me with more information about your products?
For DI-524, what rev number and firmware installed? (There are rev's. A,C,D and E)
For DWL-G700AP, what firmware (only two, shipping and 1.02)
Please check those for me.
I'm assuming your DI-524 is the DHCP router and the DWL -G700AP is connecting as a client? Are you using encryption between the two devices?
×