Question about Teac AG-360 2 Channels Receiver

1 Answer

Please, can you send me a plain of TAC AG-360 Thank you very much. Best regards, Arturo

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.


    An expert whose answer got voted for 500 times.

  • Master
  • 3,130 Answers
Re: Please, can you send me a plain of TAC AG-360 Thank...

Your asking for a service manual I presume. I do not have one, but one can be downloaded from here Good Luck

Posted on Sep 29, 2007

Add Your Answer

0 characters

Uploading: 0%


Complete. Click "Add" to insert your video. Add


3 Points

Related Questions:

1 Answer

Why is the rx v475 sending more power to one speaker than the other? It is about half power.

Is the channel distorted, or just plain low? If you require more assistance, or would like to inquire about repairing your Yamaha, please visit my website at You may contact me there. Thank you.

Dec 17, 2014 | Yamaha RX-V471 Receiver

1 Answer


Have you got the wires connected to the correct voltage D/C outputs.
What interface are you using to send the sound ( If you are using one ) If you are ensure that you are on the correct channel and the the device is sending sound. (This may sound silly but make sure you have the volume up and that you don't have headphone attached, It happens to the best of us)

Apr 29, 2013 | Teac AG-V2050

1 Answer

I need a user/owners manual for TEAC AG-D9260 please

I've the owners (user) manual for your Teac AG-D9260. But I can't send it to you by this window as it does not allow me to upload PDF files by it. I don't remember from which site I've donloaded it. If you send your email address to me by FixYa comment, I'll send a copy of it to you by return mail. OK.

Nov 25, 2011 | Teac AG-D9260 Receiver

1 Answer

My AG-V3050 pro-logic receiver seems to have a volume control issue. The test mode volume works fine but when I switch it to fm the sound is very weak, I have to crank it all the way up to get a little...

Two dump question and than recommendation..
  • First ;During listening FM ,Your " MUTE" switch is "ON" or "OFF" ? if not how about plain STEREO mode ? did you try it ?
  • about the other Modes , i.e ..CD ,DVD etc. ? same problem or it happens only in FM ? the possible solution;
sometimes FM stations do not properly triggers pro-logic circuit and cause such problem and you need to switch to STEREO or A.F.D mode to listen FM (AFM includes sub woofer)..
This is true for FM only and it should not happen in other modes as DVD ,CD,Phone etc..
Hope this helps!..if more help requires pls let me know.
Take care and please
Remember to rate/vote and give me 4 Thumbs Up for me to continue f
or Helping out the Community :)

Jun 29, 2011 | Teac AG-V3050 Receiver

1 Answer


Here are a couple of codes that might work for your TEAC receiver.
0163, 0463.

Here is a link to a site that has Remote Codes.
Hope this helps,
Best Regards,

Jan 26, 2011 | Teac AG-D9260 Receiver

2 Answers

Teac ag-d9100 center and surround speakers are not working , very very low volume.. the others all work fine. Anybody know where to start troubleshooting. Its not a fuse that I can see , at least that i...

You have to enable them and turn the volume on them up separately with the speaker config, level trim, and up/down select buttons on the remote. You can also adjust the rear speaker delay time or just hit the test tone button and adjust the volume on each speaker separately as it goes through them one at a time...

Jun 01, 2010 | Teac AG-D9100 Receiver

2 Answers

TEAC AG-D9100 freeze

Always be that legend when the audio amplifier IC damaged

May 08, 2009 | Teac AG-D9100 Receiver

1 Answer

Teac AG-V8520

same problem exactly

Oct 13, 2008 | Teac AG-V8060 Receiver

1 Answer

Kenwood VR-307 Receiver standby light blinking

Hello, sorry to say this, but there is a hardware error. Possibbly something is wrong at the output stage. Please send it to tech for a repair. But first disconnect the speakers and then try to turn it on. If there is no change the error is still present. Best regards. Arpi

Jul 17, 2007 | Kenwood VR-307 Receiver

3 Answers

Setting Up The System

You can find the requested details at:

Mar 09, 2006 | Teac AG-D8900 Receiver

Not finding what you are looking for?
Teac AG-360 2 Channels Receiver Logo

Related Topics:

134 people viewed this question

Ask a Question

Usually answered in minutes!

Top Teac Audio & Video Receivers Experts


Level 3 Expert

56836 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17129 Answers

The Knight
The Knight

Level 3 Expert

66499 Answers

Are you a Teac Audio and Video Receiver Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides