What is the wiring harness? - Car Audio & Video

About 3,970 results (0.89 seconds) Search Results

Ford Bluetooth® Wiring Harness - Crutchfield

www.crutchfield.com/.../Ford-Bluetooth-Wiring-...

Crutchfield Corporation
Rating: 4.5 - ‎16 reviews - ‎$19.99 - ‎In stock
Reinstall the factory radio and mount the Bluetooth kit, and you're ready to go. ... 16Reviews ... harness so that I could hook up an aftermarket amp to my factory radio.... works like it's suppose to. says it doesn't work on an 09 Escape but had no .... I purchased this harness to install a parrot ck3100 in my 07 Ford Edge.Missing: pwm

70-5521 wiring harness for ford with 6 CD premium sub amp ...

? 4:30
https://www.youtube.com/watch?v=0jqNafnki0o
Aug 9, 2013 - Uploaded by codieraji
Metra 70-5521 Radio Wiring Harness for Ford 03-Up Amp FordPremium stereo radio 6 CD changer with sub amp inputs. ...16:47. How to wire an aftermarket radio / I Demo install with metra harness and antenna ... How to hook up stock amp/sub to aftermarket head unit "ford sport trac" - Duration: 3:01. Pat.Missing: parakeet ‎pwm ‎98

Car Stereo Wire Harnesses - Radio Wires for all Car Audio ...

www.installer.com/main.php?page=harness
Car Stereo Wire Harnesses - Car Stereo Installation Wiring - Stereo Harness ... If you

It says the tachometer wire is Yellow/Green, you do not have that listed. You will find it in the list below, it is highlighted..

WIRING INFORMATION 2001 Subaru Legacy

WIREWIRE COLOR LOCATION

12V CONSTANT WIRE WHITE Ignition Harness

12V IGNITION WIRE GREEN Ignition Harness

12V ACCESSORY WIRE YELLOW Ignition Harness

STARTER WIRE WHITE/BLACK Ignition Harness

POWER DOOR LOCK (-) WHITE Harness In Driver's Kick Panel

POWER DOOR UNLOCK (-) GREEN/RED Harness In Driver's Kick Panel

PARKING LIGHTS (+) ORANGE At Light Switch

DOOR TRIGGER (-) PINK/BLACK In White Connector Behind Fuse Box

TRUNK TRIGGER (-) YELLOW/BLUE In White Connector Behind Fuse Box

TRUNK RELEASE (5-wire) LT.GREEN/YELLOW At Motor In Tail Gate

FACTORY ALARM ARM (-) Factory remote only

FACTORY ALARM DISARM (-) Factory remote only

TACHOMETER YELLOW/GREEN At Ignition Coil

BRAKE WIRE (+) WHITE/BLACK At Brake Pedal Switch

HORN TRIGGER (-) RED/GREEN Harness At Steering Column

LEFT FRONT WINDOW UP BLUE/RED At Driver Window Motor Inside Door

LEFT FRONT WINDOW DOWN BLUE At Driver Window Motor Inside Door

RIGHT FRONT WINDOW UP BLUE/RED Harness In Driver's Kick From Driver Door

RIGHT FRONT WINDOW DOWN BLUE Harness In Driver's Kick From Driver Door

LEFT REAR WINDOW UP BLUE/RED Harness In Driver's Kick From Driver Door

LEFT REAR WINDOW DOWN BLUE Harness In Driver's Kick From Driver Door

RIGHT REAR WINDOW UP BLUE/RED Harness In Driver's Kick From Driver Door
RIGHT REAR WINDOW DOWN BLUE Harness In Driver's Kick From Driver Door

Engine Control Module Wiring Harness Replacement - 1.4 L ...

workshop-manuals.com/.../repair.../engine_control_module_wiring_harn...

3. Unclip the 3 wiring harness clips (1, 2) from the engine control module wiring harness brackets. ... Disconnect the wiring harness connection adapter plug (4).

Engine Control Module Wiring Harness Replacement - 1.6 L ...

workshop-manuals.com/.../repair.../engine_control_module_wiring_harn...

5. If equipped, disconnect the engine oil level sensor wiring harness plug (7). ... 10. Unclip the 2 wiring harness clips (2, 6) from the wiring harness brackets.

How to fix wires that break out of plug clips on a wire harness

I believe that's a Speed Sensor issue.

Diag:
1. Ensure mainshaft and countershaft speed sensors are installed properly. Disconnect mainshaft speed sensor harness connector. Using a DVOM, measure resistance between sensor terminals.

2. If resistance is not 400-600 ohms, replace mainshaft speed sensor. If resistance is 400-600 ohms, disconnect 25-pin PCM harness connector "B". Check for continuity between ground and 25-pin PCM harness connector "B", terminals No. 15 (Red wire) and No. 14 (White wire).

3. If continuity is present, repair short to ground in Red or White wire between PCM and mainshaft speed sensor. If continuity is not present, reconnect mainshaft speed sensor harness connector. Measure resistance between 25-pin PCM harness connector "B", terminals No. 15 (Red wire) and No. 14 (White wire).

4. If resistance is not 400-600 ohms, go to next step. If resistance is 400-600 ohms, go to DTC
P0720 (FLASH CODE 9) . Check for loose PCM harness connectors. Replace PCM with a
known-good unit if necessary.

5. Disconnect mainshaft speed sensor harness connector. Check Red wire for continuity between 25-pin PCM harness connector "B", terminal No. 15 and mainshaft speed sensor harness connector. If continuity is present, go to next step. If continuity is not present, repair open in Red wire between 25-pin PCM harness connector and mainshaft speed sensor
harness connector.

6. Check White wire for continuity between 25-pin PCM harness connector "B", terminal No. 14 and mainshaft speed sensor harness connector. If continuity is present, check for loose PCM harness connectors. Replace PCM with a known-good unit if necessary. If continuity is not present, repair open in White wire between 25-pin PCM harness connector and mainshaft speed sensor harness connector.

Speed Sensor probably. Try:
1. Ensure mainshaft and countershaft speed sensors are installed properly. Disconnect mainshaft speed sensor harness connector. Using a DVOM, measure resistance between sensor terminals.

2. If resistance is not 400-600 ohms, replace mainshaft speed sensor. If resistance is 400-600 ohms, disconnect 25-pin PCM harness connector "B". Check for continuity between ground and 25-pin PCM harness connector "B", terminals No. 15 (Red wire) and No. 14 (White wire).

3. If continuity is present, repair short to ground in Red or White wire between PCM and mainshaft speed sensor. If continuity is not present, reconnect mainshaft speed sensor harness connector. Measure resistance between 25-pin PCM harness connector "B", terminals No. 15 (Red wire) and No. 14 (White wire).

4. If resistance is not 400-600 ohms, go to next step. If resistance is 400-600 ohms, go to DTC
P0720 (FLASH CODE 9) . Check for loose PCM harness connectors. Replace PCM with a
known-good unit if necessary.

5. Disconnect mainshaft speed sensor harness connector. Check Red wire for continuity between 25-pin PCM harness connector "B", terminal No. 15 and mainshaft speed sensor harness connector. If continuity is present, go to next step. If continuity is not present, repair open in Red wire between 25-pin PCM harness connector and mainshaft speed sensor
harness connector.

6. Check White wire for continuity between 25-pin PCM harness connector "B", terminal No. 14 and mainshaft speed sensor harness connector. If continuity is present, check for loose PCM harness connectors. Replace PCM with a known-good unit if necessary. If continuity is not present, repair open in White wire between 25-pin PCM harness connector and mainshaft speed sensor harness connector.

sounds like a faulty instrument cluster

I am sorry but fixya doesn't have any wiring diagrams. They are copyrighted and not free to share.

Personally owning this car and installing several Hyundai stereo's, I would purchase a wiring harness kit from car audio shop or electronics retailer. The wire harness has a plug that connects to the cars wiring harness. This wiring harness kit will also list the wires to connect your new aftermarket radio to the harness. I would also recommend using crimped **** connectors to attach the two harnesses together.

I Have the wiring harness and can get more of them. Email me @ [email protected] if you want one Jensen vm9510 harness