Question about GE DVLR223 Dryers

1 Answer

My Hotpoint TVM570P is making a dreadful noise. Looked inside and cant decide if it is the drum bearing or motor bearing. When i spin the motor or drum separately without the belt on, they both seem to spin smoothly. If i put load on the drum shaft there is some noise but not as bad as when it is running. Any clues?

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 8 Answers

Get a piece of hose and listen to each bearing. The hose should help isolate the problem.

Posted on Oct 23, 2013

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
vanni7
  • 163 Answers

SOURCE: dryer belt snaped

Hi!!! Make sure you install the belt correctly maybe this can help you..2447c24.gif

Posted on Jan 04, 2009

  • 50 Answers

SOURCE: dryer makes loud squeaking noise when spinning

there are two possibilities for this question. 1) there is an idler roller that give the belt the correct tension . unplug dryer and remove idler roller see if it spins freely if not replace it @0 there are two drum rollers in back of machine thatdrum rides on remove drum it's self explanitory how to remove drum and very easy also. you can roll these wheels and check for free movement visually check them ,one or both should be worn out or the bearing in the wheel has failed before putting old or new wheels back sand the wheel shafts to get any gunk off them and that's about the only thing that can make a dryer squeek

Posted on Jan 25, 2009

pgh_pa_guy
  • 2992 Answers

SOURCE: cant get drive belt back in place

You might find this site helpful. Good pictures and a sense of humor!

Posted on May 30, 2009

  • 1 Answer

SOURCE: Ge Adora Dryer, Worked great.

the dryer during its cycle squeaks and rumbles it sounds like some thing is not right.

Posted on Jan 03, 2010

  • 1 Answer

SOURCE: Belt Not Tight

The belt gets tight when you press the pulley arm down place the belt over the outer edge of the pulley and then over the motor axis. The belt then runs like in a "eight". Christian

Posted on May 25, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

My Hotpoint vented tumble dryer Model number


tvm 570 bearings
We have made a few videos on these dryers and there are some very good repair guides on these.
if you need parts please feel free to see site or contact me with the full model number of the ID plate How-to-Repair
How replace the bearing kit

And if you have the type with a fixed Riveted Drum shaft then you will need this video


In our repair guides you will find help on all the tumble dryer problems


How to Repair Need help fixing your appliances Need help fixing your appliances

Aug 28, 2014 | Dryers

1 Answer

Smoke coming from inside drum after spin cycle


The noise would possibly indicate that your drum bearings are on their way out, this would more than likely mean a new spider assembly, tripod in shape and houses the bearings through the drum, as well. They come in kits or bearing assembly alone for various prices, usually around 40 pounds for the kit but it would be a very difficult job if you are not familiar with this type of work, bearing extractor kits are best used but more cost, drum seals may also be needed.

Jan 23, 2014 | Hotpoint WMA35 Front Load Washer

1 Answer

Hotpoint Aquarius 1000 WM62 The drum makes a screeching noise when turning ? Any ideas ?


it could be drum bearings or even some thing that has got past the inner drum and is jamed inside hitting the drum when it turns,,,,could also be the motor bearings,,,,open the door and try lifting the inner drum up,,if there is any lift in it then the drum bearings are going,,this will also cause it to screem on spin speed

Dec 01, 2010 | Washing Machines

1 Answer

Final spinning cycle makes very loud noise.


sounds like you have the dreaded bad tub bearings. Does it sound like an aircraft taking off? Open the door and lift the drum and see if you feel any play.
I don't know your technical ability, but you can match up bearings and a seal and repair it ( frigidare will only sell you the complete drum with bearings) but its a big job as appliance work goes. You will have to decide how to proceed from there as far as fixing it or buying a new one.

Aug 11, 2010 | Frigidaire ATF6000ES Front Load Washer

1 Answer

Drum has stopped moving


Hello, these is usually the drive belt,the drive belt is the easiest parts to replace.

Thanks

Jun 10, 2010 | Hotpoint WMM39 Front Load Washer

1 Answer

Noise when agitateing wash only


Remove the belt, and spin drum by hand from inside, there should be little or no noise, if there is then it is possible the drum bearings are failing.
I f no noise, but there is when you put belt back on, then possibly bearing in motor noisy

Mar 06, 2010 | Hotpoint WMA66 Front Load Washer

1 Answer

Aquarius 1100 wm63 very noisy spinning


Remove rear cover of washer.
Remove drive belt.
From inside the drum, spin the drum by hand, if it is noisy or feels rough, then main drum bearings have failed.
If no noise, then possibly motor bearings noisy.
Hope this helps Thankyou.

Nov 27, 2009 | Hotpoint Washing Machines

1 Answer

Hotpoint WF220P has become very noisy during spin, especially at high revs. Can it be worn brushes or motor, or bearings? Otherwise all is OK.


Remove drive belt, and spin drum by hand, if it feels rough or noisy, then the main drum bearings are worn.
If no noise from drum, could be a motor prob.
Please rate ,my solution.
Thanks.

Nov 02, 2009 | Hotpoint Aquarius WF220 Front Load Washer

3 Answers

My Hotpoint WD860 makes a dreadful noise when it spins, but fine at all other times, any idea's?


Just put some grease at the bearings of the drum. This will correct the noise. However, if it persist, your bearing may need replacement.

Nov 02, 2009 | Washing Machines

1 Answer

Loud banging


Several possibilities for noise. check concrete balance wieghts at top and bottom of washer, make sure they are not loose.
Check drum restraint spring(s) are not broken.
Check suspension legs for wear.
Check for loose motor fixings.
Finally, remove drum belt, and spin drum by hand, tjhere should be noise from bearings, if it feels rough or is rumbling , then main bearings have failed.
Please rate my comments.
Thanks.

Jul 27, 2009 | Hotpoint Aquarius WD63 Front Load...

Not finding what you are looking for?
GE DVLR223 Dryers Logo

187 people viewed this question

Ask a Question

Usually answered in minutes!

Top GE Dryers Experts

John Tripp
John Tripp

Level 3 Expert

4654 Answers

JP Services
JP Services

Level 2 Expert

310 Answers

Cindy Wells

Level 3 Expert

5127 Answers

Are you a GE Dryer Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...