Question about Lands Phones

Open Question

Siemens gigaset al14h

Is my hand set ready for caller display

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

CORDLESSGURU
  • 106 Answers

SOURCE: Siemens Gigaset 4000 No Sound

Hi Krister,

It sounds from your symptoms (no pun intended) that your handset receiver/speaker has gone bad, or if you use a headset, the circuit might have gotten ripped open from tension from the headset plug. You can try plugging in a standard 2.5 mm plug headset into it (real common headset). My guess is that you will be able to hear dialtone using a headset and use the phone, but the phone will continue not ring or make key beeps.

Its fixable, but with the Siemens models don't let anyone try to open it. To work properly it needs to snap together tight, and guaranteed they will gouge the plastic and break the more than 10 tabs that keep it held snug together, there are no screws. The skill to open them without damaging them is proper training and muscle memory, which is reserved for the people that do it daily, plus if the plastic needs replacing it will add to your costs. Nevertheless, if you want it fixed, just google "Siemens Cordless Repair" and click the first or second non sponsored link to make arrangements to get it fixed. Good Luck and let me know if I was right about the headset audio.

Posted on Jan 11, 2008

CORDLESSGURU
  • 106 Answers

SOURCE: Siemens Gigaset 4200

Hello, Yes this happens when you add a additional handset to the system when all the intercom numbers are full. When registering a new handset, it "kicks out" on of the other handsets when it registers. The only way to correct that problem is to default your base and register each handset again, one by one. You won't lose your handset settings, but you will lose your messages and greetings, so check them before doing so. To default your unit, get all your handsets and go to your base. Unplug the power from your base. Hold down the page/registration key on the bottom of the base and keep it held down while you apply power to the base. After applying power, keeping the button down, count to 20. Then release the button and get each handset. Register each handset, and they will number themselves 1 through 4. If you need additional assistance, service or need to purchase another handset or base (you can register each handset to up to four bases to increase your range, this is unique feature in the cordless industry), you can go to www.cordlessrepair.com for all your Siemens cordless needs. Good Luck ! Let us know how it goes, we have a testimonial page on the website for people to leave comments on the technical tips or assistance they receive from our technicians.

Posted on Jan 11, 2008

supernova278
  • 1932 Answers

SOURCE: I have Gigaset AL14H (base

Hi,

This is because your service provider dont have this caller ID facility.
Some service provider by default have this facility activated but some service provider we need to activate this facility.

Please call your service provider to activate this facility.

Thanx

Posted on Jul 28, 2010

  • 37 Answers

SOURCE: How to tone command with a Gigaset AL14H

you can contact the service provider......

Posted on Sep 29, 2011

lindaloo1960
  • 1 Answer

SOURCE: siemens gigaset al14h what does base mean when it

HOW DO I REG HANDSETS

Posted on Sep 28, 2012

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Siemens gigaset a510ip


These NiMh batteries last a certain life -approx 3 years.

I replaced mine with 700 mAh 1.5V AAA rechargeables. Two per hansdet - buy 4 for $13.80 from EveryBattery. See everybattery.com.au or ask for the long nipple AAA NiMh cells.

Mar 18, 2014 | Siemens GIGASET-A510IP VoIP Phone w/...

1 Answer

Base is flashing and cannot dial out


HERE'S THE LINK TO THE MANUAL.
The handset is either too far from the base or it needs to be registered. The instructions are in the manual.

http://m.gigaset.com/medias/sys_master/A31008-M2050-L101-1-7619_30-10-2008_en_GBR.pdf

Dec 25, 2012 | Siemens Gigaset 4010 Cordless Phone

1 Answer

CLIP not working in siemens gigaset al140


The display should indicate what's going on with CLIP, and why it's not showing up.
You should either see an icon of a BELL, "WITHHELD" or "UNAVAILABLE".
BELL = you haven't requested CLI from your carrier
WITHHELD = if caller has withheld CLI from carrier
UNAVAILABLE = CLI is not requested.


Do you see one of these three on the display when you receive a call?


Other than one of those reasons, I'm not sure what your issue might be.

Dec 20, 2012 | Siemens Lands Phones

1 Answer

Seimens Gigaset AL285 BSNL caller ID not working


The source of my caller ID not displaying was a faulty ADSL filter.
For some reason my ADSL filter blocked the caller id information - but worked fine otherwise.
When I changed the filter the caller ID worked fine again.

Jun 05, 2012 | Siemens Lands Phones

1 Answer

How do I read messages on a siemens gigaset AL14H


THIS IS VERY FRUSTRATING,, PHONE SCREEN SAYS NEW MESSAGE BUT WAT NUMBER U PRESS TO READ MESSAGE,, WILL NOT BUY THIS BRAND AGAIN.

Jan 23, 2012 | Siemens Gigaset A490 Twin Cordless Phone

1 Answer

Gigaset showing no base n hand set display, how do we fix it?


Off hand I would say your battery is totally dead
May come back with an overnight charge

Jan 30, 2011 | Siemens Gigaset 4010 Cordless Phone

1 Answer

I have Gigaset AL14H (base and other remote one) My problem, both sets don't show caller number when I connect them in my home. I tryed them in another zone and they are OK. Is this depend on the...


Hi,

This is because your service provider dont have this caller ID facility.
Some service provider by default have this facility activated but some service provider we need to activate this facility.

Please call your service provider to activate this facility.

Thanx

Jul 28, 2010 | Siemens Gigaset 4010 Cordless Phone

1 Answer

Siemens gigaset E365. I have just purchased this phone let it charge, registered to base. I pay my telecom provider for caller ID - my previous now tired Phillips dect showed numbers of callers even names...


Does it say any of these on the display
Extern. call -means not arranged with service provider. Contact your service provider.
Withheld- Caller is withholding caller ID information.
Unavailable -your phone is not setup to display caller is with your provider.Contact them.

In addition your phone provider must support CLIP,CLI and CNIP. Confirm with your provider.

Dec 10, 2009 | Siemens Gigaset E365 Cordless Phone

Not finding what you are looking for?
Lands Phones Logo

Related Topics:

56 people viewed this question

Ask a Question

Usually answered in minutes!

Top Lands Phones Experts

kakima

Level 3 Expert

102366 Answers

Computer Repairing
Computer Repairing

Level 3 Expert

14641 Answers

yadayada
yadayada

Level 3 Expert

74945 Answers

Are you a Lands Phone Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...